Operating Power; Operating Modes; Static Color Mode - American DJ WIFLY BAR QA5 User Instructions

WiFLY Bar QA5
Notice:
Be sure to follow figures two and three when making your own
DMX512
cables. Do not use the ground lug on the XLR connector. Do not con-
DMX+,DMX-,COMMON
nect the cable's shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR's outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
1
DMX512 OUT
3
3-PIN XLR
2
REMOTE
INPUT OUTPUT
CONTROL
INPUT
XLR Male Socket
1 Ground
2 Cold
3 Hot
Figure 3
POWER
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
avoids signal transmission problems
1 1
DMX512 IN
and interference. It is always advisable
3
3-PIN XLR
to connect a DMX terminal, (Resistance
2 2
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
5-Pin XLR DMX Connectors.
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting stan-
dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
ADJ Products, LLC - www.adj.com - WiFLY Bar QA5 User Manual Page 9
POWER
COMMON
DMX +
1
DMX512 IN
3
3-PIN XLR
DMX -
2
Figure 2
REMOTE
INPUT OUTPUT
SOUND CONTROL
INPUT
XLR Female Socket XLR Pin Configuration
2 Cold
1 Ground
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
3 Hot
Pin 3 = Data True (positive)
When longer runs of cable are
Figure 4
Some manufactures use 5-pin DMX-
3-Pin XLR Female (Out) 5-Pin XLR Male (In)
Pin 1 Pin 1
Pin 2 Pin 2
Pin 3 Pin 3
Do Not Use
Do Not Use
Set Up POWER WiFLY Bar QA5

Operating Power:

There are two ways to supply power to this unit; battery power or AC
power.
• AC Power - To run the unit using AC power, plug the unit into a
power source, and put the Load Switch into the ON position. When
using AC power make sure the Battery Switch is in the OFF position.
Termination reduces signal errors and
• Battery Power - To run the unit using Battery power, put the Load
avoids signal transmission problems
1
and interference. It is always advisable
3
and Battery Switches in the ON position.
2 to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
LED Display On/Off:
press the MODE and UP buttons at the same time. To make the dis-
play turn OFF after 20 seconds, press the MODE and DOWN buttons
at the same time.

Operating Modes:

POWER
The WiFLY Bar QA5 has five operating modes:
• Static Color Mode - There are 15 colors to choose from.
• RGBA Mode - Choose one of the four colors to remain static or
adjust the intensity of each color to make your desired color.
• Built-In Program - There are 22 built-in programs to choose from.
• Auto Mode - A auto program will run with adjustable fade speed.
• Sound-Active mode - The unit will react to sound, chasing through
the built in programs.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller such as
as the ADJ Show Designer™.

Static Color Mode:

1. Plug the fixture in and press the MODE button until "CO.XX" is
displayed.
2. There are 15 colors to choose from. Select your desired color by
pressing the UP and DOWN buttons. After you have selected
your desired color you can activate strobing by pressing the SET
UP button to enter the Flash (strobe) mode.
3. "FS.XX" will be displayed, this is Flash mode. The Flash can be
adjusted between "FS.00" (flash off) to "FS.15" (fastest flash).
POWER
To make the display stay ON all of the time
ADJ Products, LLC - www.adj.com - WiFLY Bar QA5 User Manual Page 10
Operating Instructions