Table of Contents
Advertisement
Controlling the rest of your system
Renaming input source names
You can customize the names that appear on the remote
LCD when you select an input source (for example, you
could change the name of DVR 1 to HDD/DVR).
1
While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP.
2
Use
to select RENAME then press ENTER .
The LCD on the remote prompts you for the button of the
input source you want to rename.
3
Press the input source button you want to rename
then press ENTER .
4
Use
to select NAME EDT then press ENTER .
To reset the button to its original (default) name, select
NAME RST above.
5
Edit the name of the input source in the remote
control LCD, pressing ENTER when you're finished.
Use
to change the character and
forward/back a position. The name can be up to eight
characters (the possible characters are listed below).
ABCDEFGHIJKLMNOPQRSTUVWXYZ
0123456789 \ / * + – [space]
Direct function
• Default setting: ON
You can use the direct function feature to control one
component using the remote control while at the same
time, using your receiver to playback a different
component. This could let you, for example, use the
remote control to set up and listen to a CD on the receiver
and then use the remote control to rewind a tape in your
VCR while you continue to listen to your CD player.
When direct function is on, any component you select
(using the input source buttons) will be selected by both
the receiver and the remote control. When you turn direct
function off, you can operate the remote control without
1
affecting the receiver.
1
While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP.
2
Use
to select DIRECT F then press ENTER .
The LCD on the remote prompts you for the button of the
input source you want to control.
3
Press the input source button for the component
you want to control then press ENTER .
4
Use
to switch direct function ON or OFF then
press ENTER .
The LCD shows OK to confirm the setting.
Note
1 You can't use direct function with the TV CONT function.
2 • Before Multi Operation and System Off will work correctly, you must setup the remote to work with your TV and other components (see Setting the
remote to control other components on page 71 for more on this).
• Some units may take some time to power up, in which case multiple operations may not be possible.
• Power on and off commands only work with components that have a standby mode.
Multi Operation and System Off
The Multi Operation feature allows you to program a
series of up to 5 commands for the components in your
system. For example, you could turn on your TV, turn on
your DVD player and start playing the loaded DVD using
only two buttons on the remote control.
Similar to multi operations, System Off allows you to use
one button to stop and switch off a series of components
in your system at the same time.
Programming a multi-operation or a
shutdown sequence
RECEIVER
to move
CD
DVD
DVR2
DVR1
1
While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP.
2
Use
menu and press ENTER .
If you selected Multi Operation ( MULTI OP ), the LCD on
the remote prompts you for an input source button.
If you selected System Off ( SYSOFF ), go to step 4.
3
Press the input source button for the component
that will start the multi-operation then press ENTER .
For example, if you want to start the sequence by
switching on your DVD player, press DVD.
4
Use
To erase any previously stored multi-operations (or
shutdown sequences) select CODE ERS above.
5
Use
press ENTER .
If this is the first command in the sequence, select 1ST
CODE. Otherwise, simply choose the next command in
the sequence. PRES KEY flashes after you press ENTER.
6
If necessary, press the input source button for the
component whose command you want to input.
This is only necessary if the command is for a new
component (input source).
2
SYSTEM OFF
INPUT
SOURCE
D.ACCESS
SELECT
+10
AV PARAMETER
TOP MENU ì
TUNE
ST
ENTER
SETUP
TUNE
PTY SEARCH
GUIDE
TV CONTROL
TV
VIDEO 2
SAT
VIDEO 1
TV CONT
INPUT
TV VOL
TV CH
SELECT
CD-R
MULTI IN
ROOM2/3
i Pod
TUNER
RECEIVER
SLEEP
VIDEO
ANALOG
to select MULTI OP or SYS OFF from the
to select CODE EDT then press ENTER .
to select a command in the sequence then
11
CLASS
DISC
ENTER
CH LEVEL
MENU
ST
T.EDIT
ì
RETURN
BAND
VOL
73
En
Hide quick links:
Advertisement
Table of Contents
