Using The Audio Settings Of Quick Setup - Integra DTR-70.4 Instruction Manual

■
Listening Mode
*7
You can select the listening modes that are grouped in
the following categories: "MOVIE/TV", "MUSIC",
"GAME", and "THX".
Use / to select the category and
listening mode. Press Enter to switch to the selected
listening mode.
Note
*1 • The video preview is not displayed when:
– HDMI IN 5/6/7/8 is the current HDMI input source, or
– No signal is present on the current input source, or
– The "Zone 2 HDMI" setting is set to "Use" (➔ page 59).
• The video of the currently-selected input is displayed on the
main screen, not on a preview thumbnail.
*2 "Dolby Volume", "Dynamic EQ" and "Dynamic Volume"
cannot be selected when any of the THX listening modes is
selected, with "Loudness Plus" set to "On" or "Preserve
THX Settings" set to "Yes" (➔ page 66).
*3
When "Dynamic EQ" is set to "On" or "Dynamic Volume"
is set to anything else than "Off", "Dolby Volume" will be
switched to "Off" (➔ page 69).
*4
• When the "Monitor Out" setting is set to "Sub", "Video"
cannot be selected (➔ page 59).
• This setting cannot be used with the NET input selector.
*5
Only when you have selected "Custom" in the "Picture
Mode" (➔ page 74), pressing Enter allows you to adjust the
following items via the Quick Setup: "Brightness",
"Contrast", "Hue" and "Saturation". Press Return to return
to the "Picture Mode" setting.
*6 Depending on the input source and listening mode, not all
channels shown here output the sound.
*7 • This setting is not available in either of the following cases:
– The "Audio TV Out" setting is set to "On" (➔ page 81).
– "HDMI Control(RIHD)" is set to "On" (➔ page 80) and
you're listening through your TV speakers.
Using the Audio Settings of Quick
Setup
You can change various audio settings from the Quick
/ to select the
Setup (➔ page 53).
Note
• These settings are not available in either of the following cases:
– The "Audio TV Out" setting is set to "On" (➔ page 81).
– "HDMI Control(RIHD)" is set to "On" (➔ page 80) and
you're listening through your TV speakers.
Sound Program
■
Sound Program
Stereo Source 1, Stereo Source 2, Stereo Source 3,
Multich Source 1, Multich Source 2, Multich
Source 3
Off
With this setting, you can select the combination of
settings that you registered in "Sound Program Edit"
➔ page 71
( ).
Note
• If the input selector is changed, the "Sound Program" setting is
switched back to "Off".
En-54
Advanced Operations
Tone Control
■
Bass
–10dB to 0dB to +10dB in 2 dB steps.
You can boost or cut low-frequency sounds output.
■
Treble
–10dB to 0dB to +10dB in 2 dB steps.
You can boost or cut high-frequency sounds output.
You can adjust the bass for the front, front wide, front high,
center, surround, surround back and subwoofer speakers
and treble for the front, front wide, front high, center,
surround and surround back speakers, except when the
Direct or THX listening mode is selected.
Operating on the AV receiver
1
Press Tone repeatedly to select either "Bass" or
"Treble" for each speaker or subwoofer.
2 Use – and + to adjust.
Note
• Speakers that are set to "No" or "None" in "Speaker
Configuration" (➔ page 64) cannot be adjusted.
• When "Sound Program" is enabled, "Subwoofer 1" and
"Subwoofer 2" cannot be used if the "Subwoofer" setting is set
to "No" in "Sound Program Edit" (➔ page 71).