Integra DTR-40.4 Instruction Manual page 55

Speaker Configuration
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup (➔ page 34).
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify "Full Band" for speakers that can output low
frequency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover
frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker's manuals to determine the
optimum crossover frequencies. If you set up your
speakers using Audyssey 2EQ Room Correction and
Speaker Setup, please make sure manually that any THX
speakers are set to "80Hz(THX)" crossover.
■
Subwoofer
Yes
No
■
Front
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
Note
• If the "Subwoofer" setting is set to "No", the "Front" setting is
fixed at "Full Band".
■
Center , Surround
*1 *1*2
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
None
■
Front Wide , Front High
*1*3*4 *1*3*5*6
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
None
■
Surround Back
*1*2*3*5
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
®
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
None
Note
*1 "Full Band" can be selected only when "Full Band" is
selected in the "Front" setting.
*2 When the "Powered Zone 3" setting is set to "Yes"
(➔ page 54) and Zone 3 is turned on (➔ page 71), this
setting cannot be selected.
*3 If the "Surround" setting is set to "None", this setting cannot
be selected.
*4
If the "Speakers Type(Front)" setting is set to "Bi-Amp"
(➔ page 54), or the "Powered Zone 2" setting is set to "Yes"
(➔ page 54), this setting cannot be selected.
*5 If the "Speakers Type(Front)" setting is set to "Bi-Amp"
(➔ page 54), or the "Powered Zone 2" setting is set to "Yes"
(➔ page 54) together with Zone 2 turned on (➔ page 71),
this setting cannot be selected.
*6 When the "Powered Zone 3" setting is set to "Yes"
(➔ page 54), this setting cannot be selected.
■
Surround Back Ch
1ch:
Select if only one surround back speaker L is
connected.
2ch:
Select if two (left and right) surround back speakers
are connected.
Note
• If the "Surround Back" setting is set to "None", this setting
cannot be selected.
■
LPF of LFE
(Low-Pass Filter for the LFE Channel)
80Hz, 90Hz, 100Hz, 110Hz, 120Hz
Off:
Low-Pass Filter is not applied.
With this setting, you can specify the cutoff frequency of
the LFE channel's low-pass filter (LPF), which can be
En-55
Advanced Operations
used to filter out unwanted hum. The LPF only applies to
sources that use the LFE channel.
Note
• If you're using THX-certified speakers, select "80Hz".
■
Subwoofer Phase
0º
180º:
Moves the subwoofer phase.
Note
• If the "Subwoofer" setting is set to "No", this setting cannot be
selected.
■
Double Bass
This setting is NOT set automatically by Audyssey 2EQ
Room Correction and Speaker Setup (➔ page 34).
On
Off(THX)
Turn this setting on to boost bass output by feeding bass
sounds from the front left, right, and center channels to
the subwoofer.
Note
• When the "Subwoofer" setting is set to "No" or the "Front"
setting to anything other than "Full Band", this setting is fixed to
"- - - - -".
• This setting is set to "On" automatically when the "Subwoofer"
and "Front" settings are set for the first time to "Yes" and "Full
Band" respectively.
• If you're using THX-certified speakers, select "Off(THX)".