Integra DTR-40.3 Instruction Manual page 80

■
Can't connect to the AV receiver from a Web
browser
If you're using DHCP, your router may not always
allocate the same IP address to the AV receiver, so if
you find that you can't connect to a server or Internet
radio station, recheck the AV receiver's IP address
on the "Network" screen.
Check the "Network" settings.
USB Device Playback
■
Can't access the music files on a USB device
Make sure the USB device is plugged in properly.
The AV receiver supports USB devices that support
the USB mass storage device class. However,
playback may not be possible with some USB
devices even if they conform to the USB mass
storage device class.
USB memory devices with security functions cannot
be played.
Others
■
Standby power consumption
In the following cases, the power consumption in
standby mode may reach up to a maximum of 60 W:
– You are using the Universal Port jack.
– "Network Control" is set to "Enable" in the
"Network" setting.
– "HDMI Control(RIHD)" setting is set to "On".
(Depending on the TV status, the AV receiver
will enter standby mode as usual.)
– The "HDMI Through" setting is set to other than
"Off".
■
The sound changes when I connect my
headphones
When a pair of headphones is connected, the
listening mode is set to Stereo, unless it's already set
to Stereo, Mono or Direct.
■
The speaker distance cannot be set as required
In some cases, corrected values suitable for home
theater use may be set automatically.
■
How do I change the language of a multiplex
source
Use the "Multiplex" setting on the "Audio Adjust"
menu to select "Main" or "Sub".
■
The functions don't work
To use , you must make an
an analog audio connection (RCA) between the
component and AV receiver, even if they are
connected digitally.
■
The functions System On/Auto Power On and
Direct Change don't work for components
connected via
These functions don't work when Zone 2 is turned
on.
En
80
60
60
—
—
—
18, 58,
59, 60
—
—
50
20
connection and
20
■
When performing "Automatic Speaker Setup",
the measurement fails showing the message
"Ambient noise is too high."
This can be caused by a malfunction in your speaker
unit. Check if the unit produces normal sounds.
■
The following settings can be made for the
S-Video and composite video inputs
You must use the buttons on the unit to make these
settings.
On the AV receiver, press the input selector for the
input source that you want to set and the
simultaneously. While holding down the input selector
button, press until "Video ATT:On" appears on
Setup
the display. Then, release both buttons. To reactivate
the setting, repeat the above process so that "Video
ATT:Off" appears on the display, and release the
buttons.
• Video Attenuation
This setting can be made for the BD/DVD, VCR/DVR,
CBL/SAT, Game or AUX input.
If you have a game console connected to the composite
video input, and the picture isn't very clear, you can
attenuate the gain.
Video ATT:Off: (default).
Video ATT:On: Gain is reduced by 2 dB.
■
If the picture on your TV/monitor connected to
the HDMI output(s) is unstable, try switching
the DeepColor function off
To turn off the DeepColor function, simultaneously
press the CBL/SAT and On/Standby buttons on the
AV receiver. While holding down CBL/SAT, press
On/Standby until "Off" appears on the display.
Then, release both buttons. To reactivate the DeepColor
function, repeat the above process until "On" appears
on the display and release the buttons.
The AV receiver contains a microcomputer for signal
processing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit's malfunction. Before you record important
data, make sure that the material will be recorded
correctly.
Before disconnecting the power cord from the wall
outlet, set the AV receiver to standby.
—
button
Setup