Specifications - Panasonic AK-HC3800G Operating Instructions Manual

Specifications

„ General
Power supply input
Power supply : 12 V DC (during external power supply operation)
190 V DC (when CCU is connected)
Power consumption
: 25 W (during external power supply operation, camera
only)
53 W (maximum power during external power supply
operation when maximum power supplied for
each output connector while all accessories are
connected)
60 W (maximum power when CCU is connected and
maximum power supplied for each output connector
while all accessories are connected)
indicates safety information.
: –10 °C to 45 °C (14 °F to 113 °F)
Operating temperature
[Preheating required at temperatures
below 0 °C (32 °F)]
: –20 °C to 60 °C (–4 °F to 140 °F)
Storage temperature
: 85 % or less
Operating humidity
Weight : Approx. 3.7 kg (8.16 lb)
Dimensions : 135 mm x 260 mm x 367.5 mm
(W x H x D) (5-5/16 inches x 10-1/4
inches x 14-7/16 inches)
[excluding protrusions]
Basic items
1) Pickup device : 2/3˝ 2.2 million pixel IT, CCD x 3
2) System : GBR pickup system
3) Color separation optical system
: f/1.4 prism
4) Optical filter : ND: Clear, 1/4, 1/16, 1/64
5) Lens mount : Bayonet type
6) Output standard : SMPTE 292M
7) Sensitivity : F11 (When vertical frequency is 59.94 Hz)
F12 (When vertical frequency is 50 Hz)
8) Horizontal resolution : 1100 TV lines
9) S/N : 60 dB or higher
10) Horizontal frequency : 33.716 kHz, 1125-line frame
(Vertical frequency: 59.94 Hz)
28.125 kHz, 1125-line frame
(Vertical frequency: 50 Hz)
11) Vertical frequency : 59.94 Hz or 50 Hz, interlace
Input/output signals
1) MIC input : –60 dBu to 4 dBu
(XLR 3-pin female x 2)
Gain selected by camera menu
2) Intercom : Input: -60 dBu to -20 dBu
Output: 100 mW max.
(XLR 5-pin female x 1)
3) HD-SDI1/HD-SDI2 output : HD signal = 0.8 V [p-p], 75 ohms (BNC)
The HD-SDI2 signal output can be added
to the regular images using the camera
menu item setting and switched to the VF
or RET image output.
4) Prompt output : VBS signal = 1 V [p-p], 75 ohms (BNC)
5) DC OUT : 12 V, MAX. 1A
Control
1) Power switching : CCU, OFF, EXT
2) USER 1, 2, 3 : Functions specified by menu items can
be assigned to the switch.
3) RET A/B selection : For selecting the return signal
4) RET/PTT switching : RET, PPT
5) Gain selection : LOW, MID, HIGH
*
1
6) Output selection : CAM, BAR, TEST
* 1
7) White balance mode : A, B, preset
*
1
8) Shutter speed selection : 1/100, 1/120, 1/125, 1/250, 1/500,
* 1
1/1000, 1/1500, 1/2000
9) AWB, ABB SW
* 1
10) Menu selection
11) CALL SW
12) Intercom : MIC ON/OFF, receiving level, or PGM
level
13) MIC setting : MIC power, MIC gain, MIC1 selection
*
1
When the CCU is connected, the selection functions cannot be used.
Control is performed from the ROP.
33