Other Settings; Troubleshooting - Casio 3258 Operation Manual

To specify standard time or daylight saving time (DST) for a city
1. In the World Time Mode, use
the available city codes.
• Keep scrolling until the city code whose Standard Time/Daylight
Saving Time setting you want to change is displayed.
2. Hold down
disappears.
• This toggles the city code you selected in step 1 between Daylight
Saving Time (DST indicator displayed) and standard time (DST
indicator not displayed).
• Using the World Time Mode to change the DST setting of the
city code that is selected as your Home City also will change the
Timekeeping Mode time DST setting.
• Note that you cannot switch between standard time/daylight
saving time (DST) while UTC is selected as the World Time City.
• Note that the standard time/daylight saving time (DST) setting
affects only the currently selected time zone. Other time zones are
not affected.
DST indicator DST indicator
E-96
3. Press to toggle the illumination duration between three seconds (LT3 displayed) and 1.5 seconds
(LT1 displayed).
4. After all of the settings are the way you want, press
• To return to the screen in step 1, press
About the Auto Light Switch
Turning on the auto light switch causes illumination to turn on,
whenever you position your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and
then tilting it towards you more than 40 degrees causes
illumination to turn on.
Warning!
• Always make sure you are in a safe place whenever you are reading the display of the watch
using the auto light switch. Be especially careful when running or engaged in any other activity
that can result in accident or injury. Also take care that sudden illumination by the auto light
switch does not startle or distract others around you.
• When you are wearing the watch, make sure that its auto light switch is turned off before riding
on a bicycle or operating a motorcycle or any other motor vehicle. Sudden and unintended
operation of the auto light switch can create a distraction, which can result in a traffi c accident
and serious personal injury.
E-98
Illumination Precautions
• The electro-luminescent panel that provides illumination loses power after very long use.
• Illumination may be hard to see when viewed under direct sunlight.
• Illumination turns off automatically whenever an alarm sounds.
• Frequent use of illumination runs down the battery.
Auto light switch precautions
• Wearing the watch on the inside of your wrist, movement of your arm, or vibration of your arm can
cause frequent activation of the auto light switch and illumination of the display. To avoid running down
the battery, turn off the auto light switch whenever engaging in activities that might cause frequent
illumination of the display.
• Note that wearing the watch under your sleeve while the auto light switch is turned on can cause
frequent illumination of the display and can run down the battery.
• Illumination may not turn on if the face of the watch is more than 15 degrees above
or below parallel. Make sure that the back of your hand is parallel to the ground.
• Illumination turns off after the preset illumination duration (page E-97), even if you
keep the watch pointed towards your face.
• Static electricity or magnetic force can interfere with proper operation of the auto
light switch. If illumination does not turn on, try moving the watch back to the
starting position (parallel with the ground) and then tilt it back towards your face
again. If this does not work, drop your arm all the way down so it hangs at your
side, and then bring it back up again.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
E-100
To turn Power Saving on and off
1. In the Timekeeping Mode, hold down
the display and then the city code starts to fl ash.
2. Use to cycle through the settings on the display until the the current
power saving setting (On or OFF) is displayed.
• See the sequence in step 2 of the procedure under "To change
the current time and date settings manually" (page E-32) for
information about how to scroll through setting screens.
3. Press to toggle Power Saving on (On) and off (OFF).
4. After all of the settings are the way you want, press
setting screen.
Power saving Power saving
• To return to the screen in step 1, press
on indicator on indicator
Note
• The Power Saving on indicator (PS) is on the display in all modes
while Power Saving is turned on.
E-102
Operation Guide 3258
(East) and (West) to scroll through
until DST Hold appears on the display and then Hold
to exit the setting screen.
again.
Wear the watch on the Wear the watch on the
outside of your wrist outside of your wrist
until SET Hold appears on
to exit the
again.
Illumination
To change the illumination duration
1. In the Timekeeping Mode, hold down
starts to fl ash.
2. Use to cycle through the settings on the display until the current illumination duration (LT1 or LT3) is
shown.
• See the sequence in step 2 of the procedure under "To change the current time and date
settings manually" (page E-32) for information about how to scroll through setting screens.
Note
• This watch features a "Full Auto EL Light", so the auto light switch operates only when available light is
below a certain level. It does not illuminate the display under bright light.
• The auto light switch is always disabled, regardless of its on/off setting, when any one of the following
conditions exists.
While an alarm is sounding
During sensor measurement
While a bearing sensor calibration operation is being performed in the Digital Compass Mode
More than More than
While a receive operation is in progress in the Receive Mode
40° 40°
While the Moon age or tide information is being calculated
To turn the auto light switch on and off
Auto light switch on Auto light switch on
indicator indicator

Other Settings

The button operation tone sounds any time you press one of the watch's buttons. You can turn the button
operation tone on or off as desired.
• Even if you turn off the button operation tone, the alarm, Hourly Time Signal, and Countdown Timer
Mode alarm all operate normally.
To turn the button operation tone on and off
Mute indicator Mute indicator

Troubleshooting

Time Setting
See "Radio Controlled Atomic Timekeeping" (page E-14) for information about adjusting the time setting
according to a time calibration signal.
■ The current time setting is off by hours.
Your Home City setting may be wrong (page E-28). Check your Home City setting and correct it, if
necessary.
■ The current time setting is off by one hour.
If you are using the watch in an area where time calibration signal reception is possible, see "To confi gure
Home City settings" (page E-28).
If you are using in the watch in an area where time calibration signal reception is not possible, you may
need to change your Home City's standard time/daylight saving time (DST) setting manually. Use the
procedure under "To change the current time and date settings manually" (page E-31) to change the
standard time/daylight saving time (DST) setting.
Sensor modes
■ I can't change the temperature, barometric pressure, and altitude units.
When TYO (Tokyo) is selected as the Home City, the altitude unit is set automatically to meters (m), the
barometric pressure unit to hectopascals (hPa), and the temperature unit to Celsius (°C). These settings
cannot be changed.
The display of the watch is illuminated for easy reading in the dark.
The watch's auto light switch turns on illumination automatically when
you angle the watch towards your face.
• The auto light switch must be turned on (page E-99) for it to operate.
To turn on illumination manually
Press in any mode to illuminate the display.
• You can use the procedure below to select either 1.5 seconds or three
seconds as the illumination duration. When you press
will remain illuminated for about 1.5 seconds or three seconds,
depending on the current illumination duration setting.
• The above operation turns on illumination regardless of the current
auto light switch setting.
• Illumination is disabled during time calibration signal reception, while
confi guring sensor measurement mode settings, and during bearing
sensor calibration.
until SET Hold appears on the display and then the city code
In the Timekeeping Mode, hold down for about three seconds to toggle
the auto light switch on ( displayed) and off (
• The auto light switch on indicator ( ) is on the display in all modes
while the auto light switch is turned on.
• The auto light switch turns off automatically whenever battery power
drops to Level 4 (page E-10).
1. In the Timekeeping Mode, hold down until SET Hold appears on
the display and then the city code starts to fl ash.
2. Use to cycle through settings on the display until the current button
operation tone (MUTE or BEEP) is displayed.
• See the sequence in step 2 of the procedure under "To change the
current time and date settings manually" (page E-32) for
information about how to scroll through setting screens.
3. Press to toggle the button operation tone on (BEEP) and off (MUTE).
4. After all of the settings are the way you want, press
setting screen.
• To return to the screen in step 1, press
Note
• The mute indicator is displayed in all modes when the button
operation tone is turned off.
, the display
E-97
not displayed).
E-99
to exit the
again.
E-101
E-103