Sample System; Other Options - GE PM880 Specifications

Moisture Measurement
Compatibility
Compatible with all GE aluminum oxide moisture probes:
M Series, TF Series, and Moisture Image Series. Each
probe type requires a different type of I/O cable.
Calibration
GE moisture sensors are computer-calibrated to National
Institute of Standards and Technology (NIST) traceable
moisture concentrations.
Dew/Frost Point Temperature
Overall Calibration Range Capability
-166°F to 140°F (–110°C to 60°C)
Calibration Range Options
• Standard: 68°F to -112°F (20°C to –80°C) with data to
-166°F (–110°C)
• Ultralow: -58°F to -166°F (–50°C to –110°C)
• Extended high: 140°F to -112°F (60°C to –80°C) with
data to -166°F (–110°C)
Accuracy
• ±3.6°F (±2°C) from 140°F to -85°F (60°C to –65°C)
• ±5.4°F (±3°C) from -85°F to -166°F (–65°C to –110°C)
Repeatability
• ±0.9°F (±0.5°C) from 110°F to -85°F (60°C to –65°C)
• ±1.8°F (±1.0°C) from -86°F to -166°F (–66°C to –110°C)
Operating Pressure
5 µ of Hg to 5000 psig (345 bar) limited by pressure
sensor—see pressure measurement specifications
Temperature Measurement
Optional thermistor available for all GE moisture probes
Range
–22°F to 158°F (–30°C to 70°C)
Accuracy
±0.9°F (±0.5°C) at -22°F (–30°C)
© 2013 General Electric Company. All Rights Reserved. Specifications are subject to change without notice. GE is a registered trademark of General Electric Company. Other company or product
names mentioned in this document may be trademarks or registered trademarks of their respective companies, which are not affiliated with GE.
Pressure Measurement
Optional pressure sensor available for TF Series and
Moisture Image Series moisture probes
Ranges
• 30 to 300 psig (3 to 21 bar)
• 50 to 500 psig (4 to 35 bar)
• 100 to 1000 psig (7 to 69 bar)
• 300 to 3000 psig (21 to 207 bar)
• 500 to 5000 psig (35 to 345 bar)
Accuracy
±1% at full scale
Proof Pressure
Three times span of available range up to maximum
7500 psig (518 bar)

Sample System

The SS880A standard sample system comprises an inlet
needle valve, a built-in coalescing filter and sample cell
with a bypass needle valve and venting tube, a pressure
gauge (various ranges), and an outlet needle valve with
venting tube.
Wetted Parts
316 SS
Operating Pressure
Configurations available for 300, 500, 1000, 2000, or
3000 psig (21, 35, 69, 207, or 345 bar), dependent on
pressure gauge)
Maximum Pressure Rating
• Standard: 3000 psig (207 bar)
• Optional: 5000 psig (345 bar)

Other Options

• Inlet pressure regulator, 0 to 500 psig (1 to 345 bar)
outlet
• Armored flowmeter, 1.3 to 13 SCFH
• 10-ft (3-m), flexible, polytetrafluoroethylene-lined,
braided–stainless steel hose with 1/4-inch tube
connections. Not recommended for dew point
temperatures below –103°F (–75°C).
www.ge-mcs.com
920-007H