GE JN327 Owner's Manual And Installation Instructions page 12

11 MARK HOLES
Select the vent option that your installation will
require and proceed to that section:
A. Outside top exhaust
(Vertical duct–3 1
• Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
Hood mounting screws (4)
" (30" hood)
13 3 ⁄
4
" (36" hood)
16 3 ⁄
4
Cabinet front
Cabinet Bottom
"
5 1 ⁄
4
Vertical duct
"
3 3 ⁄ access hole
4
"
1 ⁄
2
Wood shims
(recessed-bottom cabinets
only–shims must be a
"
minimum of 3/8 thick
and cut to fit the width
of the inner recessed
cabinet bottom)
B.Outside top exhaust (Vertical duct–7
• Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
Hood mounting screws (4)
" (30" hood)
13 3 ⁄
4
" (36" hood)
16 ⁄
3
4
Cabinet front
Cabinet
bottom
Access
"
hole for 7
round duct
Wood shims
Center
(recessed-bottom cabinets
only–shims must be a minimum
"
of 3/8 thick and cut to fit the
width of the inner recessed
cabinet bottom)
Installation Instructions
" "
⁄ x 10 Rectangular)
4
" (30" hood)
13 ⁄
3
4
" (36" hood)
16 3 ⁄
4
"
7 3 ⁄
4
"
5 1 ⁄
4
"
1 1 ⁄
4
1
Electrical access hole
(in cabinet bottom)
Center
line
"
Round)
" (30" hood)
13 3 ⁄
4
" (36" hood)
16 3 ⁄
4
"
7 ⁄
3
4
"
8 DIA.
"
1 1 ⁄
HOLE 4
"
5 ⁄
3
4
1
Electrical access
hole
(in cabinet bottom)
line
C. Outside rear exhaust
(Horizontal duct–3
• Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
Wood shims
(recessed-bottom cabinets only–shims must be a
minimum of 3/8
of the inner recessed cabinet bottom)
"
9 5 ⁄
8
"
3 ⁄
8
Hood mounting screws (4)
D. Recirculating (non-vented ductless–
JN327 and RN328, and optional on
JV347, JV348 and JV367 models only)
• Use the hood as a template and mark the locations
on the cabinet for the electrical wiring and keyhole
screw slots.
• Since the hood is to be recirculated (not to be vented
outside), do not cut out any vent openings in the wall
or cabinet bottom.
12
CUT HOLES
Cut holes at marked locations for duct and electrical
wiring. For the vertical duct, cut out 3/4" extra
toward the front of the cabinet so you can move the
duct freely when installing the hood. It may also ease
installation by cutting the hole 10
"
9 5 ⁄
8
"
3 ⁄
8
13 RUN WIRES
Run the electrical wires through the wall or
cabinet according to National Electrical Code
and applicable local codes.
NOTE: DO NOT turn the power on until
installation is complete.
12
"
⁄ x 10
1
4
"
thick and cut to fit the width
Cabinet front
" Horizontal duct
3 3 ⁄
4
access hole
Cabinet
"
5 1 ⁄
5 1 ⁄
bottom
4
" (30" hood)
13 ⁄ 13
3
4
" (36" hood)
16 3 ⁄ 16
4
Center line
"
Rectangular)
"
"
1 ⁄ 1 1 ⁄
2
4
"
4
"
7 3 ⁄
4
" (30" hood)
3 ⁄
4
" (36" hood)
3 ⁄
4
Electrical access hole
(in wall)
" instead of 10".
1 ⁄
2