Table of Contents
Advertisement
Quick Links
GEAppliances.ca
. . . . . . . . . . . 2
Operating/Care and
Cleaning Instructions
Charcoal Filter . . . . . . . . . . . . . . .4
Grease Filter . . . . . . . . . . . . . . . . .3
Hood Light . . . . . . . . . . . . . . . . . .4
Hood Surfaces . . . . . . . . . . . . . . . .4
Controls . . . . . . . . . . . . . . . . . . . . .3
Consumer Support
Consumer Support . . .Back Cover
Warranty . . . . . . . . . . . . . . . . . . . 14
*
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
You can find them on a label on the
back wall of the hood.
. . .5-13
350A4502P522 49-80424 06-06 JR
Owner's Manual and
Installation Instructions
JN327-Recirculation only
JV338*-Vent options only
JV347*-Vent & Recirculation
options
JV348*-Vent & Recirculation
options
JV367*-Vent & Recirculation
options
RN328-Recirculation only
Advertisement
Table of Contents
Related Manuals for GE JN327 Series
Summary of Contents for GE JN327 Series
-
Page 1: Table Of Contents
GEAppliances.ca Safety Information ... 2 Owner’s Manual and Installation Instructions Operating/Care and Cleaning Instructions JN327–Recirculation only Charcoal Filter ....4 JV338*–Vent options only Grease Filter . -
Page 2: Safety Information
IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING. SAFETY PRECAUTIONS WARNING – WARNING – TO REDUCE THE RISK OF FIRE, TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE A RANGE TOP GREASE FIRE: THE FOLLOWING: A. Never leave surface units unattended at high A. -
Page 3: Grease Filter
To replace: your dealer. Order genuine GE Slip the back edge of the filter part number WB02X8391 . into the retaining tabs and push the front edge up until it snaps... -
Page 4: Charcoal Filter
Pull down on the center of the front WB02X10700. Replacement filters edge of the filter. The filter will then can be ordered from your GE supplier. slip out of the retaining tabs on the back. If the hood is not vented to the... -
Page 5: Installation Instructions
An optional Power Cord Connection Kit, model total equivalent ductwork length using the approximate JXHC1, is available at extra cost from your GE feet of equivalent length of some typical ducts. supplier for installation using a standard 3-prong, grounded wall outlet. - Page 6 Installation Instructions WORKSHEET—CALCULATE TOTAL EQUIVALENT DUCTWORK LENGTH* DUCT EQUIVALENT NUMBER DUCT EQUIVALENT NUMBER PIECES LENGTH x USED = TOTAL PIECES LENGTH x USED = TOTAL 3¼” x 10” 1 Ft. 6” Round 24 Ft. Rect., wall cap (18 ft. w/o straight with damper)
- Page 7 Installation Instructions DAMAGE – SHIPMENT/INSTALLATION TOOLS YOU WILL NEED • If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. • If the unit is damaged by the customer, repair or Flat blade and Phillips Pencil replacement is the responsibility of the customer.
- Page 8 Installation Instructions CHOOSE VENT OPTION Determine the vent option that your installation will IMPORTANT: If the hood is to be installed in a require and that is available for your model from the recirculating, non-vented ductless manner, do not below choices. knock out any vent openings in the hood.
- Page 9 Installation Instructions REMOVE WIRING COVER REMOVE EXHAUST ADAPTOR* If exhausting/venting using the 3¼” x 10” rectangular Remove the wiring cover from inside the hood. Set the cover and its mounting screw aside. duct—optional for JV338, JV347, JV348 and JV367 models only: Wiring Remove the exhaust adaptor from the inside of the cover...
- Page 10 Installation Instructions FOR RECESSED-BOTTOM FOR 3¼” X 10” RECTANGULAR DUCTED DISCHARGE CABINETS ONLY* INSTALLATIONS ONLY:* Attach exhaust adaptor/damper over the appropriate knockout opening (for vertical or horizontal, depending on installation) with two exhaust adaptor screws. Make sure damper pivot is nearest to top/back edge of hood.
- Page 11 Installation Instructions MARK HOLES* C.Outside rear exhaust (Horizontal duct–3¼ x 10 Rectangular) Select the vent option that your installation will ” ” require and proceed to that section: • Use the diagram or the hood as a template and mark the locations on the cabinet for ductwork, A.Outside top exhaust electrical wiring and keyhole screw slots.
- Page 12 KIT JXHC1* Mounting An optional Power Cord Connection Kit, model screw (4) JXHC1, is available at extra cost from your GE supplier for installation using a standard 3-prong, Keyhole (4) grounded wall outlet. Follow the Installation Instructions packed with the kit to connect the power cord to the range hood.
- Page 13 Installation Instructions INSTALL LIGHT BULB REPLACE FILTER NOTE: A light bulb is not shipped with the hood. Make sure fan blade turns freely and replace the Obtain one locally. Purchase and install an ordinary filter. NOTE: On models JV347 and JV348, install screw-base light bulb, not more than 60 watts.
- Page 14 GE Range Hood Warranty. All warranty service provided by our Factory Service Centers, or Staple your receipt here. an authorized Customer Care technician. To schedule service, ® Proof of the original purchase on-line, 24 hours a day, visit us at GEAppliances.ca, or call date is needed to obtain service 1-800-361-3400.
-
Page 15: Consumer Support
GE Appliances Website GEAppliances.ca Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals, order parts or even schedule service on-line.