Table of Contents
Advertisement
Available languages
Available languages
About special features.
10
To Enter Special Features
To enter the bulk tank Special Features Mode:
1
Press the Power button.
2
Simultaneously press and hold either the
Detergent Tank On and Detergent Cup Amount buttons
for 3 seconds
or
Softener Tank On and Softener Cup Amount buttons for
3 seconds
The My Settings
and Extra Rinse lights will flash to
indicate you are in the Special Features Mode.
Option 1: Set Concentration Settings
NOTE: During initial installation, or if the household
water pressure dramatically changes, the bulk
dispenser will change to accommodate your homes'
unique water pressure. Wait a few wash cycles before
changing concentrations.
The factory default concentration settings are 1.5 oz
(44 ml) for detergent and 1.0 oz (30 ml) for softener.
To allow maximum user flexibility either of these can
be changed to between 0.5 and 10 ounces.
1
Enter Special Features mode. See To Enter Special
Features section above.
2
Press the My Settings
button.
The My Settings and the chosen (Detergent or Softener)
3 Cup Amount lights will come on and the Extra Rinse
light will go out. The display will show "10 times in ounces"
the current concentration setting (e.g. 15 represents 1.5
ounces). This amount will be dispensed when 2 (of the 3)
Cup Amount lights are lit.
The following table shows the approximate amount dispensed (oz) at each Cup Amount setting (1, 2 or 3) for each
Concentration Setting:
Concentration
5
10
15
Setting
Number of
200 100
67
Loads*
0.6
1.3
1.9 2.5 3.1 3.8 4.4 5.0 5.6 6.3 6.9 7.5 8.1 8.8 9.4 10.0 10.6 11.3 11.9
0.5
1.0
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5
0.4
0.8
1.1 1.5 1.9 2.3 2.6 3.0 3.4 3.8 4.1 4.5 4.9 5.3 5.6
* For a 100 oz (2957 ml) bottle for normal (
Option 2: SmartDispense
1
Enter Special Features mode. See To Enter Special
Features section above.
2
Remove all articles from the washer basket.
3
Press the Extra Rinse button.
The My Settings
and lights will go out. The Start
button light will blink. The corresponding Tank Levels
lights will show the current tank level.
4
Press the Start button.
The tank will dispense for the minutes shown in the
display to empty the selected tank. The Tank Levels
lights will cycle 0,1,2,3,4,5,4,3,2,1,0 until the flush is
finished.
Once finished, the Tank Level will indicate an empty tank
(a single blinking red LED light) and the Start button will
3
4
This function will then exit and the display will reflect
whatever cycle the cycle knob is on.
To exit without changing the setting, press the Power
button. This function will automatically exit (without
saving) if neither button is pressed within 1 minute.
20
25
30
35
40
45
50
50
40
33
29
25
22
20
) setting.
Tank Cleaning
TM
be lit. You can (repeatedly) refill the tank with water and
press the Start button to rinse out the tank as needed.
NOTE: If you suspect that the dispenser is plugged, add
lemon juice to make the water slightly acidic.
5
This function will automatically exit if neither button is
pressed for 2 hours.
NOTE: Bulk tank flush is recommended if you:
1) Change detergent or softener brands
2) Accidently add softener to the detergent tank or
3) Put powdered detergent in the detergent tank
4) Put non-concentrated fabric softener in the
OR
Turn the cycle knob clockwise to increase or
counter-clockwise to decrease the setting (within
preset limits). Each click increases or decreases Level
2 (standard amount) by 1/2 ounce. Levels 1 & 3
change proportionally.
Press the Cup Amount button to save the new
setting.
55
60
65
70
75
80
18
17
15
14
13
13
8.0
6.0
Press the Power button to exit (when the tank is
empty).
vice versa
softener tank
85
90
95
100
12
11
11
10
12.5
8.5
9.0
9.5
10.0
6.4
6.8
7.1
7.5
Advertisement
Table of Contents
