Table of Contents
Advertisement
4. Wire zone device to the keypad Blue and Gray wires.
EZM Zone 50ms Response (Default = 0)
The default loop response of each keypad expansion zone is 750mS,
however the response time of any zone can be reduced to 50mS as
follows:
To reduce zone 1 to 50mS, enter 1 on the display and press
To reduce zone 2 to 50mS, enter 2 on the display and press
To reduce both zone 1 and 2 to 50mS, enter 3 and press
Access Control Message (Default = 0)
The default Access-Control message is "**ENTER NOW**".
display may be changed to any of the following messages:
ENTRY
MESSAGE
0
"** ENTER NOW **" (Default)
1
"Door Control"
2
"Gate Control"
3
"Light Control"
Enter the number of the message you wish displayed and press
Exit Delay Time Display (Default = 045)
The delay time which permits exit through an Exit/Entry Zone after the
system is armed, allows a user to leave the premises without setting
off an immediate alarm. Exit Delay may be programmed for up to 255
seconds (4¼ minutes). Enter the number of seconds and press
Note: Changing this configuration updates the keypad only, not the
panel. The panel delay time is updated via Dealer Mode only; to keep
the panel and keypad delay times synchronized, be certain to program
the keypad for the same time as programmed for the panel.
Entry Delay Time Display (Default = 030)
Entry delay time permits entry through Exit/Entry Zone(s) after the
system is armed without setting off an immediate alarm. Entry Delay
allows the user time to enter and disarm the system. Upon entering,
the keypad sounder will sound an entry sound to remind the user to
disarm the system. Entry Delay Time may be programmed for up to
255 seconds (4¼ minutes). Enter the number of seconds and press
U
. Note: Changing this configuration updates the keypad only, not
the panel. The panel delay time is updated via Dealer Mode only; be
certain to program the keypad for the same time as programmed for
the panel.
Exiting Keypad Configuration Mode
Press
to loop back through selections or press
R
the Zone Descriptions Mode, in which you can change the zone de-
scriptions that appear on the keypad display. If you wish to exit the
Keypad Configuration Mode, press
SYSTEM"). Replace the green wire to the Remote Bus Panel Terminal.
Display will display panel status.
ZONE DESCRIPTIONS MODE
Zones are independent circuits that protect specific areas of the
premises. The displayed zone descriptions may be changed to suit the
particular design of the premises. To change Zone Descriptions:
1.
Disconnect green wire from Remote Bus panel terminal.
2.
Press
and the display reads "OUT OF SYSTEM".
C
3.
Enter factory code: 11123
The software version number appears briefly, then "RP CONFIGURA-
TION MODE" appears. After a few seconds, the words "Feedback
Beep Presently ON" appear.
4.
Press
C
and "ZN DESCRIPTIONS MODE" displays.
Scroll descriptions forward or backward using
To return to normal keypad operation, press
wire to the Remote Bus panel terminal.
After entering Zone Descriptions Mode, the keypad will automatically return
to "OUT OF SYSTEM" if no activity is detected for longer than 4 minutes.
C
(display will read "OUT OF
C
.
R
R
and
B
, respectively.
and reconnect the green
C
01=ACCOUNTING
02=ALARM
03=APARTMENT
04=AREA
05=ATTIC
06=BABYS
U
07=BACK
.
08=BASEMENT
09=BATH
10=BEDROOM
U
.
11=BOYS
12=CEILING
13=CLOSET
U
.
14=COMPUTER
15=CONTROL
16=DEN
17=DEPARTMENT
This
18=DETECTOR
19=DINING
20=DOOR
21=DOWN
Entering a new zone description
Use
R
U
Use
1
.
Use
3
Use
4
wards and forwards.
With the cursor located under a word, use button
U
entire word to the left, and use
.
U
Press
Quick Word List
The keypad contains pre-programmed zone descriptions, avoiding the
need to scroll through individual numbers, letters, and symbols. Press
followed by the two-digit number of the entry listed in the Quick
G
Word List table (above). For example, to enter the description "DINING
ROOM", press
after Quick Words are entered, and entering
existing word.
LCD TO LCD TRANSFER OPTION
Zone descriptions can be transferred from the programmed keypad
(master) to the unprogrammed others (slaves) in the system.
1.
Program the primary keypad (master) with the appropriate zone
descriptions, etc, as described in Zone Descriptions Mode above.
2.
As a safety precaution, remove AC and DC power to the panel.
to enter
3.
Wire all keypads to the panel and reapply power.
The LCD TO LCD TRANSFER OPTION is accessed through Keypad
Configuration Mode, as follows:
4.
Disconnect green wire from Remote Bus panel terminal.
5.
Press
C
6.
Enter the factory code of 11123
The software version number appears briefly, then the words "RP
CONFIGURATION MODE" appear.
"Feedback Beep Presently ON" appear.
7.
Press
C
display. The keypad is now ready to replicate keypad data to the
other keypads in the system.
8.
In order for the transfer to take place, all keypads must be physically
linked to each other and isolated from the panel. Therefore, connect all
green wires from all keypads. Do not connect green wires to panel.
9.
To initiate the transfer, press
transmitting data to all slaves. The words SENDING are displayed
as the keypad cycles through the database (which is displayed on
the LCD during this process).
"SENDING STOPPED...PLEASE WAIT" will display. Similarly, the slave
keypads receiving data will display" RECEIVING".
10. When complete, the words "OUT OF SYSTEM" will display.
connect all wires as described previously for normal operation.
Quick Word List
22=DOWNSTAIRS
43=INTERIOR
23=EAST
44=KITCHEN
24=ENTRY
45=LAUNDRY
25=EXERCISE
46=LEFT
26=EXIT
47=LIVING
27=FAMILY ROOM
48=LOBBY
28=FIRE
49=LOW
29=FIRST
50=MAIDS
30=FLOOD
51=MASTER
31=FLOOR
52=MOTION
32=FOIL
53=NORTH
33=FOYER
54=OFFICE
34=FRENCH
55=PHONE
35=FRONT
56=PLAY
36=GARAGE
57=PORCH
37=GATE
58=PROTECTION
38=GIRLS
59=REAR
39=GLASS
60=RIGHT
40=GREAT
61=ROOM
41=GUEST
62=SAFE
42=HALL
63=SALES
and
to scroll to the desired zone.
B
and
to position the cursor within the display.
2
and
to scroll through numbers, letters, etc.
6
and
to erase text while moving the cursor back-
5
to move the word to the right.
8
to save when the zone description is complete.
1 9
6 1. Note: A space is automatically set
G
G
and the display will read "OUT OF SYSTEM".
R
After a few seconds, the words
and
and "LCD TO LCD TRANSFER OPTION" will
P
U
. The master keypad will start
At short intervals, the words
64=SHED
65=SHIPPING
66=SIDE
67=SKYLIGHT
68=SLIDING
69=SMOKE
70=SOUTH
71=SPACE
72=STAIRS
73=STUDY
74=TAMPER
75=TEMPERATURE
76=UPSTAIRS
77=UTILITY
78=WAREHOUSE
79=WEST
80=WINDOW
81=WORKSHOP
82=UP
to move the
7
splits an
G 0 0
.
Re-
Page 3
- Quick Links:
- Keypad Configuration Mode
Hide quick links:
Advertisement
Table of Contents
