Troy-Bilt CSV 206 Operation Manual
  1. Manuals
  2. Brands
  3. Troy-Bilt Manuals
  4. Lawn and Garden Equipment
  5. CSV 206
  6. Operation manual

Troy-Bilt CSV 206 Operation Manual

Chipper/shredder vacuum
Hide thumbs Also See for CSV 206:

Advertisement

Table of Contents

See also: Operator's Manual
Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
O
'
M
peratOr
s
anual
Chipper Shredder Vacuum
Model CSV 206
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA
Form No. 769-06181
(June 9, 2010)

Advertisement

Table of Contents
loading

Related Manuals for Troy-Bilt CSV 206

Summary of Contents for Troy-Bilt CSV 206

  • Page 1 READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Printed In USA Form No. 769-06181...

  • Page 2: Table Of Contents

    Choose from the options below: ◊ Visit us on the web at www.troybilt.com ◊ Call a Customer Support Representative at (800) 828-5500 or (330) 558-7220 ◊ Write us at Troy-Bilt LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019...

  • Page 3: Safe Operation Practices

    Important Safe Operation Practices WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury.
  • Page 4 Safe Handling of Gasoline: If the impeller strikes a foreign object or if your machine should start making an unusual noise or vibration, To avoid personal injury or property damage use extreme care immediately shut the engine off. Allow the impeller to in handling gasoline.
  • Page 5 Maintenance & Storage Do not modify engine Never tamper with safety devices. Check their proper To avoid serious injury or death, do not modify engine in any operation regularly. way. Tampering with the governor setting can lead to a runaway engine and cause it to operate at unsafe speeds.
  • Page 6 Safety Symbols This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR’S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate WARNING—...

  • Page 7: Assembly & Set-Up

    Assembly & Set-Up Contents of Carton • One Chipper Shredder Vacuum • One Operator’s Manual • One Engine Operator’s Manual • One Chipper Chute • One Nozzle • One Safety Glasses • One Bag • One Tamper (If Equipped) • One Bottle of Oil Assembly NOTE: This unit is shipped without gasoline or oil in the engine.
  • Page 8 Remove the three hex nuts and bell washers from the weld studs beside the opening on the right side of the chipper- Place bag under the upper handle assembly and slip the shredder vacuum. See Fig. 3-3B. front opening on the bag over the discharge chute, making Place the chipper chute over the weld studs keeping the certain it is over the rim on the discharge chute.
  • Page 9 Adjustments Front Caster Wheels This chipper shredder vacuum is equipped with front caster Nozzle Height wheels. The casters can be locked in a straight ahead position or to swivel freely. The nozzle adjustment levers are located on each side of the nozzle door.

  • Page 10: Controls & Features

    Controls and Features Chipper Chute Drive Control Vacuum/ Chipper Caster Lock Nozzle Door Adjustment Lever Figure 4-1 Vacuum/Chipper Bag WARNING: Be familiar with all controls and their proper operation. Know how to stop the machine Collects shredded or chipped material fed through the chipper and disengage them quickly.

  • Page 11: Operation

    Operation Starting Engine Repeat the previous steps until engine fires. When engine starts, move choke control (if equipped) gradually to RUN WARNING: Keep bystanders, helpers, pets, and position. children at least 75 feet from the machine before NOTE: See your engine manual packed with your unit for starting and while operating.

  • Page 12: Maintenance & Adjustment

    Maintenance & Adjustments Maintenance Engine Care • Refer to the separate engine manual for all engine General Recommendations maintenance instructions. • Always observe safety rules when performing any • Check engine oil level before each use as instructed in the maintenance.
  • Page 13 Adjustments Remove the two hex bolts and hex nuts which extend through the impeller housing. See Fig. 6-2A. Drive Control Cable Periodic adjustment of the drive control cable may be required if: • The chipper shredder vacuum moves forward with the drive control disengaged.

  • Page 14: Service

    Service Blade Care Remove other blade in the same manner to replace or sharpen. WARNING: Before performing any type of WARNING: Use caution when replacing the blades. maintenance on the machine, wait for all parts to Wear heavy gloves to avoid injury while handling stop moving and disconnect the spark plug wire.

  • Page 15: Troubleshooting

    Troubleshooting Problem Cause Remedy Engine Fails to start Throttle lever not in correct starting position. Move throttle lever to FAST or START position. Spark plug wire disconnected. Connect wire to spark plug. Choke not in CHOKE position (if equipped). Move choke lever to CHOKE position. Fuel tank empty or stale fuel.

  • Page 16: Replacement Parts

    Replacement Parts Component Part Number and Description 759-3336 Spark Plug BS-491588S Air Filter Cartridge BS-493537S Pre-Cleaner BS-792647 Fuel Cap BS-694485 Fuel Filter 964-04001 (800) 828-5500 or (330) 558-7220 Phone to order replacement parts or a complete Parts Manual (have your full model number and serial number ready).
  • Page 17 Component Part Number and Description 942-0544B Chipper Blade (2 total) 719-04308 Flail Blade (3 total) 634-0244 Wheel (Rear) 734-1804A Wheel (Front) 954-0457 Belt (800) 828-5500 or (330) 558-7220 Phone to order replacement parts or a complete Parts Manual (have your full model number and serial number ready).

  • Page 20: Warranty

    MANUFACTURER’S LIMITED WARRANTY FOR The limited warranty set forth below is given by Troy-Bilt LLC with c. Routine maintenance items such as lubricants, filters, blade respect to new merchandise purchased and used in the United States sharpening, tune-ups, brake adjustments, clutch adjustments,...

Table of Contents