Burner Adjustments - Lennox Crestline LSBV-3628MN Care And Operation Instructions Manual

LENNOX HEARTH PRODUCTS • CRESTLINE™ SERIES B-VENT GAS FIREPLACES • 36"/42" LSBV MODELS • CARE AND OPERATION INSTRUCTIONS

BURNER ADJUSTMENTS

(QUALIFIED TECHNICIANS ONLY)
Flame Appearance and Sooting
Proper flame appearance is a flame which is
blue at the base and becomes yellowish-orange
in the body of the flame.
When the appliance is first lit, the entire flame
may be blue and will gradually turn yellowish-
orange during the first 15 minutes of operation.
After 15 minutes of operation, if the flame is
blue, or if the flame is orange with evidence of
sooting (black tip), the air shutter opening may
need to be adjusted.
If the air shutter opening is closed too far,
sooting may develop. Sooting is indicated by
black puffs developing at the tips of very long
orange flames. Sooting results in black deposits
forming on the logs, appliance inside surfaces
and on exterior surfaces adjacent to the vent
termination.
Sooting is caused by incomplete combustion
in the flames and lack of combustion air enter-
ing the air shutter opening. To achieve a warm
yellowish-orange flame with an orange body
that does not soot, the shutter opening must be
adjusted between these two extremes.
Air Shutter Adjustment guidelines
• If there is smoke or soot present, first check
the log set positioning to ensure that the
flames are not impinging on any of the logs.
If the log set is properly positioned and a
sooting condition still exists, then the air
shutter opening should be increased.
• The more offsets in the vent system, the larger
the air shutter opening will need to be.
• An appliance operated with the air shutter
opened too far, may have flames that appear
blue and transparent. These weak, blue and
transparent flames are termed anemic.
• Propane models may exhibit flames which
candle or appear stringy. If this is present
and persists, adjust the air shutter to a more
closed position, then operate the appliance
for a few more minutes to ensure that the
flame normalizes and the flames do not
appear sooty.
The following chart is provided to aid you in
achieving the correct air shutter adjustment
for your installation.
Air Shutter Adjustment guidelines
Amount of Flame
Primary Air Color
If air shutter is Flame will
closed too far be orange
If air shutter is Flame will
open too far be blue
12
Burner Flame Adjustments
To adjust the flame, position the air shutter
to the nominal setting (see Figure 14). Allow
the burner to operate for at least 30 minutes.
Observe the flame continuously.
If it appears weak or sooty as previously
described, adjust the air shutter open or closed
until desired effect is achieved.
NOTE: If the flame still appears anemic with the
air shutter closed all the way (usually a result of
lengthy vertical venting runs), turn off the appli-
ance, turn off the gas supply, wait for the parts
to cool and access the air shutter. The shutter is
prevented from actually closing by a tab that is
bent over into the opening. Remove this obstruc-
tion by bending back. Reassemble and restart the
appliance and after 24 minutes observe the flame.
Adjust the air shutter as described.
• Soot will be produced if the
air shutter is closed too much.
Any damage due to sooting,
resulting from improperly
setting the air shutter, is not
covered under the warranty.
• The air shutter door and
nearby appliance surfaces
are hot. Exercise caution to
avoid injury while adjusting
flame appearance.
:
Air Shutter
Adjustment
Air shutter
gap should be
increased
Air shutter
Figure 13
gap should be
decreased
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
CAUTION
- Burner Flame Appearance
WARNINg
• Air shutter adjustment should
only be performed by a quali-
fied professional service tech-
nician.
Factory Air
gas
Models Shutter Setting
Type
Inches (mm)
Natural 1/8" (3.175 mm)
LSBV-3628
Propane 1/2" (12.7 mm)
Natural 1/8" (3.175 mm)
LSBV-4228
Propane 1/2" (12.7 mm)
Figure 14