Miller Electric Millermatic 250 Owner's Manual page 28

Note
Base selection of drive rolls upon the following recommended usages:
1
2
3
4
5
Wire Diameter
Fraction
.023/.025 in.
.030 in.
.035 in.
.045 in.
Item Dia. Part
No. Mkgs. No.
. . . 1 . . . . . . . . . . . 134 834
. . . 2 . . . . . . . . . . . 149 332
. . . 3 . . . GS1 . . . 125 785
. . . 4 . . . . . . . . . . . 143 810
. . . 5 . . . . . . . . . . . 169 654
. . . 6 . . . . . . . . . . . 602 387
. . . 7 . . . . . . . . . . . 605 227
. . . 8 . . . . . . . . . . . 044 426
. . . 9 . . . . . . . . . . . 010 493
. . . 10 . . . . . . . . . . . 148 242
. . . 11 . . . FM1 . . . 148 808
. . . 12 . . . . . . . . . . . 148 809
. . . 13 . . . . . . . . . . . 049 399
.
Hardware is common and
not available unless listed.
13
To maintain the factory original performance of your equipment, use only Manufacturer's Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM–1308 Page 24
Table 6-1. Drive Roll And Wire Guide Kits
V-Grooved rolls for hard wire.
U-Grooved rolls for soft and soft shelled cored wires.
U-Cogged rolls for extremely soft shelled wires (usually hard surfacing types).
V-Knurled rolls for hard shelled cored wires.
Drive roll types may be mixed to suit particular requirements (example: V-Knurled roll in combination
with U-Grooved).
Decimal Metric
.023/.025 in. 0.6 mm
.030 in. 0.8 mm
.035 in. 0.9 mm
.045 in. 1.2 mm
Description
Figure 6-5. Panel, Rear w/Components (Fig 6-1 Item 10)
. . . HOSE, SAE .187 ID x .410 OD (order by ft)
. . . CLAMP, hose .405-.485clp dia slfttng
. . . VALVE, 24VAC 2 way custom port 1/8 orf
. . . PANEL, rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . BRACKET, support tank
. . . CHAIN, weldless 2/0 x 27.000 lg
. . . NUT, nyl hex jam .750NPST
. . . CONNECTOR, clamp cable .690/1.070
. . . BUSHING, snap-in nyl .625 ID x .875mtg hole
. . . WINDTUNNEL, 9 in
. . . MOTOR, fan 230V 1550RPM .312dia shaft
. . . BLADE, fan 9 in 5wg 34deg .309 bore CCW
. . . NUT, speed push-on-type .312 stud .625 OD x .456 ID
2
1
11
12
Figure 6-5. Panel, Rear w/Components
Drive Roll
Kit No.
Part No.
087 131 087 130
079 594 053 695
079 595 053 700
079 596 053 697
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
4
3
9
10
Inlet
Wire Guide
Type
V-Grooved 056 192
V-Grooved 056 192
V-Grooved 056 192
V-Grooved 056 193
Ref. S-0026-B/7-91
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . .
6
7
8
Quantity
3ft
2
1
1
1
1
1
1
1
1
1
1
1
ST-148 327-C