Seagate ST1000LM014 Product Manual
Seagate laptop sshd
Hide thumbs
Also See for ST1000LM014:
- Product manual (44 pages) ,
- Datasheet (2 pages) ,
- Product manual (34 pages)
Related Manuals for Seagate ST1000LM014
Summary of Contents for Seagate ST1000LM014
- Page 1 Product Manual Seagate Laptop SSHD ® Standard models Self-Encrypting Drive models ST1000LM014 ST1000LM015 ST750LM000 SED (FIPS 140-2) models ST1000LM028 Gen 1 100716627 Rev. C June 2013...
- Page 2 Publication number: 100716627, Rev. C June 2013 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Seagate Laptop SSHD and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries.
-
Page 3: Table Of Contents
ONTENTS ......... . . 1 EAGATE ECHNOLOGY UPPORT... - Page 4 IGURES 5V S ......8 IGURE YPICAL TARTUP AND PERATION URRENT ROFILE SATA C .
-
Page 5: Seagate Technology Support Services
Authorized Service Centers For information regarding Warranty Support, visit:http://www.seagate.com/support/warranty-and-replacements/ For information regarding data recovery services, visit http://www.seagate.com/services-software/data-recovery-services/ For Seagate OEM and Distribution partner portal, visit: http://www.seagate.com/partners/ For Seagate reseller portal, visit: http://www.seagate.com/partners/my-spp-dashboard/ Seagate Laptop SSHD SATA Product Manual, Rev. C... -
Page 6: Introduction
NTRODUCTION ® This manual describes the functional, mechanical and interface specifications for the following Seagate Seagate Laptop SSHD model drives: Standard models Standard SED models SED (FIPS 140-2) models ST1000LM014 ST1000LM015 ST1000LM028 ST750LM000 Previous generations of Seagate Self-Encrypting Drive models were called Full Disk Encryption (FDE) models before a differentiation between drive-based encryption and other forms of encryption was necessary. -
Page 7: About The Serial Ata Interface
ATA I BOUT THE ERIAL NTERFACE The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jumpers or other configuration options. -
Page 8: Drive Specifications
The specification summaries listed in the following tables are for quick reference. For details on specification measurement or definition, refer to the appropriate section of this manual. Table 1 Drive Specifications Summary ST1000LM014, ST1000LM015 ST750LM000 RIVE PECIFICATION... -
Page 9: Formatted Capacity
14 (words 60-61 and 100-103) for additional information about 48-bit addressing support of drives with capacities over 137 GB. HYSICAL ORGANIZATION Drive model Read/write heads Number of discs ST1000LM014, ST1000LM015 and ST1000LM028 ST750LM000 SSHD SATA P EAGATE APTOP RODUCT... -
Page 10: Recording And Interface Technology
RIVE PECIFICATIONS ECORDING AND NTERFACE ECHNOLOGY Interface Serial ATA (SATA) Recording method Perpendicular Recording density 1894 Kb/in Track density 375 ktracks/in avg Areal density 705 Gb/in Spindle speed 5400 RPM +/- 0.2% Sustained data transfer rate 100 MB/s max I/O data-transfer rate 600 MB/s max HYSICAL HARACTERISTICS... -
Page 11: Power Specifications
RIVE PECIFICATIONS OWER PECIFICATIONS The drive receives DC power (+5V) through a native SATA power connector (refer to Figure 2.7.1 Power consumption Power requirements for the drives are listed in the table in Table 4. Typical power measurements are based on an average of drives tested, under nominal conditions, at 25°C ambient temperature. -
Page 12: Conducted Noise
RIVE PECIFICATIONS 2.7.1.1 Typical current profiles The typical 5V startup and operation current profile is shown in Figure Figure 1 Typical 5V Startup and Operation Current Profile 2.7.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. ... -
Page 13: Power Management Modes
NVIRONMENTAL PECIFICATIONS This section provides the temperature, humidity, shock, and vibration specifications for Seagate Laptop SSHD drives. Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Above 1000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. -
Page 14: Shock
Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards. -
Page 15: Electromagnetic Immunity
To determine the warranty for a specific drive, use a web browser to access the following web page: :http://www.seagate.com/support/warranty-and-replacements/ From this page, click on the “Verify Your Warranty” link. You will be asked to pro- vide the drive serial number, model number (or part number) and country of pur- chase. -
Page 16: Agency Certification
Communications Commission verification or certification of the device is required. Seagate has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disk drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is likely to result in interference to radio and television reception. -
Page 17: Environmental Protection
Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. -
Page 18: Configuring And Mounting The Drive
Figure Figure 2 Attaching SATA Cabling Signal connector Power connector Signal cable Power cable Each cable is keyed to ensure correct orientation. Seagate Laptop SSHD SATA drives support latching SATA connectors. SSHD SATA P EAGATE APTOP RODUCT ANUAL... -
Page 19: Drive Mounting
RIVE OUNTING You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. Refer for drive mounting dimensions. Follow these important mounting precautions when mounting the drive: Figure 3 ... -
Page 20: About Fips
'Security Rules' section in the 'Security Policy' document uploaded on the NIST website. To reference the product certification visit: http://csrc.nist.gov/groups/STM/cmvp/documents/140-1/1401vend.htm, and search for “Seagate”. Security Level 2. Security Level 2 enhances the physical security mechanisms of a Security Level 1 cryptographic module by adding the requirement for tamper-evidence, which includes the use of tamper-evident coatings or seals on removable covers of the module. -
Page 21: (Sata) ((Sata)) Interface
For detailed information about the Serial ATA interface, refer to the Serial ATA: High Speed Serialized AT Attachment specification. OMPATIBILITY Seagate Laptop SSHD SATA drives incorporate connectors which enable you to hot plug these drives in accordance with the Serial ATA: High Speed Serialized AT Attachment specification revision 2.0. This specification can be downloaded from www.serialata.org. This device requires a COMRESET from the host after a hotplug event. -
Page 22: Sata C
ATA (SATA) I ERIAL NTERFACE • the signal pins and the rest of the power pins. There are three power pins for each voltage. One pin from each voltage is used for pre-charge when installed in a blind-mate backplane configuration. All used voltage pins (V ) must be terminated. - Page 23 ATA (SATA) I ERIAL NTERFACE Table 9 Supported ATA commands ATA-standard commands names Command code (in hex) Set Multiple Mode S.M.A.R.T. Disable Operations B0h/D9h S.M.A.R.T. Enable/Disable Autosave B0h/D2h S.M.A.R.T. Enable Operations B0h/D8h S.M.A.R.T. Enable/Disable Auto Offline B0h/DBh S.M.A.R.T. Enable One Attribute Modification B0h/E0h S.M.A.R.T.
-
Page 24: Identify Device Command
0004 23–26 Firmware revision: x.xx (8 ASCII character string, padded with blanks to end of string) 27–46 Drive model number: ST1000LM014 (40 ASCII characters, padded with blanks to end of string) ST1000LM015 ST1000LM028 ST750LM000 (Bits 7–0) 8010 Maximum sectors per interrupt on Read multiple and Write multiple... - Page 25 Word Description Value 60–61 Total number of user-addressable sectors ST1000LM014 = 0FFFFFFFh This field contains a value that is one greater than the total number ST1000LM015 = 0FFFFFFFh ST1000LM028 = 0FFFFFFFh user-addressable sectors. The maximum value that shall be placed ST750LM000 = 0FFFFFFFh in this field is 0FFFFFFFh.
- Page 26 98-99 Streaming Performance Granularity 0000 100– Total number of user-addressable LBA sectors available ST1000LM014 = 1,953,525,168 (see Section 3.2 for related information) ST1000LM015 = 1,953,525,168 These words are required for drives that support the 48-bit address- ST1000LM028 = 1,953,525,168 ST750LM000 = 1,465,149,168 feature.
- Page 27 ATA (SATA) I ERIAL NTERFACE Table 11 Bit Descriptions (continued) Ultra DMA mode 0 is supported. Ultra DMA mode 1 is supported. Ultra DMA mode 2 is supported. Ultra DMA mode 3 is supported. Ultra DMA mode 4 is supported. Ultra DMA mode 5 is supported.
-
Page 28: Set Features Command
ATA (SATA) I ERIAL NTERFACE 5.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. -
Page 29: Commands
) that eliminates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at: http://www.seagate.com/support/downloads/seatools/. This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that supports S.M.A.R.T. to enable this feature. - Page 30 NDEX errors 11 ESD 14 acoustics 10 EU 12 active mode 9 EU RoHS directive 13 Address 18 European Union (EU) requirements 12 agency certification 12 evice Configuration Identify 18 ambient temperature 6 Execute Device Diagnostics 18 areal density 6 ATA commands 18 Australia/New Zealand Standard AS/NZS3548 1995 12 FCC verification 12...
- Page 31 S.M.A.R.T. implementation 18 safety certification 12 operating shock 10 SATA ports 3 operating vibration 10 screws 15 Seagate Technology Support Services 1 sectors 5 physical characteristics 6 Security Disable Password 19 Physical organization 5 Security Erase Prepare 19 point-to-point 3...
- Page 32 Transport major version number 22 UL60950-1 12 vibration 10 voltage dips, interrupts 11 voltage tolerance 8 warranty 11 weight 6 width 6 Write Buffer 19 Write DMA 19 Write DMA Extended 19 Write Long with Retries 19 Write Long without Retries 19 Write Multiple 19 Write Sectors 19 SSHD SATA P...
- Page 33 Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00 Publication Number: 100716627, Rev.