Step 8. Installing Logs - Lennox MLDVT-30NM Installation Instructions Manual

LENNOX HEARTH PRODUCTS • MERIT
Step 8. INSTALL VOLCANIC STONE,
GLOWING EMBERS, AND LOGS
NOTE: Turn off all electricity to the appliance
before you install volcanic stone, embers and
logs.
1. Remove the front glass enclosure panel
(see Removing Glass Enclosure Panels on
Page 31).
2. Locate log set, embers and volcanic stone.
Handle logs carefully to prevent breakage.
3. Install decorative volcanic stone - Sprinkle
the decorative volcanic stone in a pleasing
pattern (see Figure 45). The volcanic stone
should be placed directly on top of the firebox
bottom, along the slope and to the back at the
right and left sides of the burner. Position any
ceramic fiber liners before placing the stone.
Logs can be positioned after the volcanic stone.
Volcanic Stone
Place Volcanic
Figure 45
Stone As Shown
4. Placement of Glowing Embers -
Separate the Embers (rockwool) into pieces
about the size of a quarter (see Figure 46).
Keep the pieces fluffed up, not matted. Dis-
tribute these pieces over the surface of the
burner, as shown in Figures 47 and 48. Do
not use more than is necessary. Ensure that
the main burner slots remain uncovered by
the ember material. Position the embers on
the small holes of the ember bed area.
Note: This appliance is provided with enough
Glowing Embers for several applications, do
not use all that is in a new bag at one time.
For best glowing effect, replace the ember
material annually.
28
SERIES DIRECT-VENT GAS FIREPLACES • MODELS MLDVT-30/35/40/45 • INSTALLATION INSTRUCTIONS
®
Glowing Embers
Separate into Quarter
Size (separate) Pieces
Bag of Glowing
Embers (rockwool)
Figure 46
5. Placement of Logs -
The logs have locating notches or slots to
help ensure that they are properly positioned.
The top logs that rest on lower logs, do so
over notches, indents or nubs. Proper log
placement is critical to prevent sooting. Logs
should be placed in the gaps between the flame
peaks and should be positioned so they do not
impinge the flames. Follow the log placement
instructions, exactly.
MLDVT-30 & MLDVT-35 - Install the five logs
as Follows:
Carefully position the ceramic fiber logs over
the burner as shown in Figure 47. Logs should
be placed in the order shown and per the fol-
lowing instructions.
1. Place the rear log (1) as shown. Position
it on the left rear log bracket.
2. Place the left front log (2) as shown. Posi-
tion it against the left front of the log rack.
3. Place the right front log (3) as shown. Posi-
tion it against the right front of the log rack.
4. Place the left cross log (4) as shown. Posi-
tion it over the rear log (1), with the front of
the log resting on the log rack.
5. Place the right cross log (5) as shown.
Position it over the right log (3), and rest the
rear of the log over the right rear bracket.
MLDVT-40 & MLDVT-45 - Install the five logs
as Follows:
Carefully position the ceramic fiber logs over
the burner as shown in Figure 48. Logs should
be placed in the order shown and per the fol-
lowing instructions.
1. Place the rear log (1) as shown. Position
it on the left rear log bracket.
2. Place the left front log (2) as shown. Posi-
tion it against the left front of the log rack.
3. Place the right front log (3) as shown. Posi-
tion it against the right front of the log rack.
4. Place the left cross log (4) as shown. Posi-
tion it over the rear log (1), with the front of
the log resting over log (2).
5. Place the right cross log (5) as shown.
Position it over the right log (3), and rest the
rear of the log over the right rear bracket.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
REFERENCE
Firebox Accessories / Parts
Cat. No. Model No. Description
88L53 FGE Bag of Glowing Embers
Bag of Decorative
80L42 FDVS
Volcanic Stone
WARNING
• DO NOT attempt to install the
logs until the appliance instal-
lation has been completed, the
gas line connected and tested
for leaks and the initial burner
operation has been checked
out.
• The size and position of the log
set was engineered to give the
appliance a safe, reliable and
attractive flame pattern. Any
attempt to use a different log
set in the fireplace will void
the warranty and will result in
incomplete combustion, soot-
ing, and poor flame quality.
• Logs get very hot and will
remain hot up to one hour
after gas supply is turned off.
Handle only when logs are
cool. Turn off all electricity
to the appliance before you
install grate, volcanic stone,
vermiculite, embers and logs.
• This appliance is not designed
to burn wood. Any attempt to
do so could cause irreparable
damage to the appliance and
prove hazardous to your safety.
• If logs are not installed
according to the log instal-
lation instructions, flame
impingement and improper
combustion could occur and
result in soot and/or excessive
production of carbon monoxide
(CO), a colorless, odorless,
toxic gas.