Page 1 FIAT 500 ABARTH 2 0 1 3 O W N E R ’ S M A N U A L...
Page 2 WARNING! FIAT is a registered trademark of FIAT Group Marketing & Corporate Communication SpA, used under license by Driving after drinking can lead to an accident. Your Chrysler Group LLC.
Page 3: Introduction 3
TABLE OF CONTENTS SECTION PAGE INTRODUCTION ............. 3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE .
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 VEHICLE IDENTIFICATION NUMBER ..7 HOW TO USE THIS MANUAL ....5 VEHICLE MODIFICATIONS/ALTERATIONS .
Page 6: Introduction
- all essentials that are maintaining its validity traditional to our vehicles. • the range of additional services available to FIAT This Owner’s Manual has been prepared with the assis- Group Automobiles customers tance of service and engineering specialists to acquaint NOTE: After reviewing the owner information, it you with the operation and maintenance of your vehicle.
Page 7: How To Use This Manual
INTRODUCTION 5 HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment. The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects.
Page 8 6 INTRODUCTION...
Page 9: Vehicle Identification Number
INTRODUCTION 7 WARNINGS AND CAUTIONS This Owners Manual contains WARNINGS against oper- ating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information.
Page 10: Vehicle Modifications/Alterations
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN.
Page 11: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A WORD ABOUT YOUR KEYS ....11 To Lock The Doors And Liftgate ... .16 Ignition Key Removal .
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Untwisting Procedure ..32 Air Bag Deployment Sensors And Controls ..43 Seat Belts In Passenger Seating Positions ..32 Event Data Recorder (EDR) ....52 Automatic Locking Retractor Mode (ALR) —...
Page 13: Things To Know Before Starting Your Vehicle 9
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 A WORD ABOUT YOUR KEYS The vehicle is supplied with a code card containing key code numbers to order duplicate keys, and the autho- The key fob contains the Remote Keyless Entry (RKE) rized studio that sold you your new vehicle has the key transmitter with an integrated key.
Page 14 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Before exiting a vehicle, always turn the ignition to the OFF/LOCK position, apply the parking brake, shift the transmission into REVERSE gear, and remove the key fob from the ignition. When leav- ing the vehicle, always lock your vehicle.
Page 15: Locking Doors With A Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key-In-Ignition Reminder WARNING! (Continued) Opening the driver’s door when the key is in the ignition • Do not leave children or animals inside parked and the ignition switch position is OFF/LOCK, sounds a vehicles in hot weather.
Page 16: Replacement Keys
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A key which has not been programmed is also Replacement Keys considered an invalid key, even if it is cut to fit the NOTE: Only keys that have been programmed to the ignition switch lock cylinder for that vehicle.
Page 17: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. •...
Page 18: To Lock The Doors And Liftgate
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seconds, to unlock all doors and the liftgate. The turn signal NOTE: Changes or modifications not expressly ap- lights will flash to acknowledge the unlock signal. The proved by the party responsible for compliance could illuminated entry system will also turn on.
Page 19 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 1. Press the mechanical key release button and release 2. Rotate the screw located on the side of the Key Fob the mechanical key to access the battery case screw using a small screwdriver. located on the side of the Key Fob.
Page 20: Door Locks
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS The door locks can be manually locked or unlocked from inside the vehicle by using the door handle. If the door handle is pushed a red lock indicator will show on the door handle (indicating locked) when the door is closed, the door will lock.
Page 21 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 WARNING! WARNING! (Continued) • Allowing children to be in a vehicle unattended is • Do not leave children or animals inside parked dangerous for a number of reasons. A child or vehicles in hot weather. Interior heat build-up may others could be seriously or fatally injured.
Page 22: Power Door Locks
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A power door lock switch is incorporated into the door handle. Push or pull the handle to lock or unlock the doors and liftgate. If the door handle is pushed a red lock indicator will show on the door handle (indicating locked) when the door is closed, the door will lock.
Page 23: Power Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 To change the Autoclose setting in the EVIC, proceed as POWER WINDOWS follows: Power Window Switches 1. Briefly press the MENU ESC button “On” or “Off” There are single window controls located on the shifter will flash on the display (according to the previous bezel, below the climate controls, which operate the setting).
Page 24: Liftgate
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE down automatically. To cancel the Auto-Down move- ment, operate the switch in either the up or down direction and release the switch. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.
Page 25 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 To open the liftgate, squeeze the liftgate release handle WARNING! and pull the liftgate open with one fluid motion. • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes.
Page 26: Occupant Restraints
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • All seat belt systems (except the driver’s) include OCCUPANT RESTRAINTS Automatic Locking Retractors (ALRs), which lock the Some of the most important safety features in your seat belt webbing into position by extending the belt vehicle are the restraint systems: all the way out and then adjusting the belt to the •...
Page 27 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Here are some simple steps you can take to minimize the You should read the instructions provided with your risk of harm from a deploying air bag: child restraint to make sure that you are using it properly. 1.
Page 28 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. If the air bag system in this vehicle needs to be WARNING! (Continued) modified to accommodate a disabled person, contact • Being too close to the steering wheel or instrument the Customer Center. Phone numbers are provided in panel during Advanced Front Air Bag deployment If You Need Consumer Assistance.
Page 29: Lap/Shoulder Belts
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 of the worst injuries happen when people are thrown WARNING! from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the In a collision, you and your passengers can suffer inside of the vehicle.
Page 30 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Wearing your belt in the wrong place could make • It is dangerous to ride in a cargo area, inside or your injuries in a collision much worse. You might outside of a vehicle.
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 2. The seat belt latch plate is along side the pillar near the 3. When the belt is long enough to fit, insert the latch back of your seat. Grasp the latch plate and pull out plate into the buckle until you hear a “click.”...
Page 32 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • A belt that is worn under your arm is dangerous. • A belt buckled into the wrong buckle will not Your body could strike the inside surfaces of the protect you properly.
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 4. Position the lap belt across your thighs, below your WARNING! abdomen. To remove slack in the lap belt portion, pull • A lap belt worn too high can increase the risk of up on the shoulder belt.
Page 34: Lap/Shoulder Belt Untwisting Procedure
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. Lap/Shoulder Belt Untwisting Procedure The belt will automatically retract to its stowed posi- Use the following procedure to untwist a twisted lap/ tion.
Page 35: Automatic Locking Retractor Mode (Alr) - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 For additional information, refer to “Installing Child ratcheting sound as the belt retracts. Allow the webbing Restraints Using The Vehicle Seat Belt” under the “Child to retract completely in this case and then carefully pull Restraints”...
Page 36: Energy Management Feature
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Engage The Automatic Locking Mode WARNING! 1. Buckle the combination lap and shoulder belt. • The belt and retractor assembly must be replaced if 2. Grasp the shoulder portion and pull downward until the seat belt assembly Automatic Locking Retractor the entire belt is extracted.
Page 37: Seat Belt Pretensioners
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Seat Belt Pretensioners Enhanced Seat Belt Use Reminder System (BeltAlert ) The seat belts for both front seating positions are equipped with pretensioning devices that are designed to BeltAlert is a feature intended to remind the driver and remove slack from the seat belt in the event of a collision.
Page 38: Seat Belt Extender
BeltAlert can be enabled or disabled by your authorized Using a seat belt extender when not needed can dealer. FIAT Group Automobiles S.p.A. does not recom- increase the risk of injury in a collision. Only use mend deactivating BeltAlert .
Page 39: Seat Belts And Pregnant Women
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Seat Belts And Pregnant Women Driver Side Knee Air Bag mounted in the instrument panel below the steering column. We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe.
Page 40 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The Driver and Front Passenger Advanced Front and rear passengers sitting next to a window. The SABIC Air Bags are certified to the Federal regulations for are located above the side windows. The trim covering Advanced Air Bags.
Page 41: Advanced Front Air Bag Features
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 • Steering Wheel and Column Advanced Front Air Bag Features • Instrument Panel The Advanced Front Air Bag system provides output appropriate to the severity and type of collision as • Supplemental Driver Side Knee Air Bag determined by the Occupant Restraint Controller (ORC), •...
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Seat-Mounted Side Air Bags (SAB) WARNING! (Continued) Supplemental Seat-Mounted Side Air Bags (SAB) provide • Do not put anything on or around the air bag enhanced protection to help protect an occupant during a covers or attempt to open them manually.
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only.
Page 44 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system includes side impact sensors that are cali- WARNING! (Continued) brated to deploy the Seat-Mounted Side Air Bags (SAB) • Your vehicle is equipped with SABIC air bags, do and SABIC during impacts that require air bag occupant not have any accessory items installed which will protection.
Page 45: Air Bag Deployment Sensors And Controls
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Along with seat belts and pretensioners, Advanced Front Side Air Bags (SAB), and front seat belt pretensioners, as Air Bags work with the Supplemental Driver Side Knee required, depending on several factors, including the Air Bag and the passenger side knee bolster to provide severity and type of impact.
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The side air bags will not deploy in all side collisions. The ORC contains a backup power supply system that Side air bag deployment will depend on the severity and may deploy the air bags even if the battery loses power or type of collision.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Advanced Front Air Bags. Different air bag inflation rates WARNING! are possible, based on several factors, including the collision type and severity. The steering wheel hub trim Ignoring the Air Bag Warning Light in your instru- cover and the upper right side of the instrument panel ment panel could mean you won’t have the air bags separate and fold out of the way as the air bags inflate to...
Page 48 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A large quantity of non-toxic gas is generated to inflate triggered, releasing a quantity of non-toxic gas. The the Supplemental Driver Side Knee Air Bag. The trim inflating SAB exits through the seat seam into the space cover separates and folds out of the way allowing the air between the occupant and the door.
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 A quantity of non-toxic gas is generated to inflate the side Enhanced Accident Response System curtain air bag. The inflating side curtain air bag pushes In the event of an impact causing air bag deployment, if the outside edge of the headliner out of the way and the communication network remains intact, and the covers the window.
Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Carefully check the vehicle for fuel leaks in the engine System Reset Procedure compartment and on the ground near the engine com- After an impact causing air bag deployment, the left and partment and fuel tank before resetting the system and right turn signal lights, located in the instrument panel starting the engine.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Customer Action Customer Will See 6. Turn Left Turn Signal Switch ON. Left Turn Light is ON SOLID. Right Turn Light is ON SOLID. 7. Turn Left Turn Signal Switch OFF. (Turn Signal Switch Left Turn Light is OFF.
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the air bags, any irritation, rinse the area with cool water. For nose or or all of the following may occur: throat irritation, move to fresh air. If the irritation continues, see your doctor.
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Maintaining Your Air Bag System WARNING! (Continued) • Do not attempt to modify any part of your air bag WARNING! system. The air bag may inflate accidentally or may • Modifications to any part of the air bag system not function properly if modifications are made.
Page 54: Event Data Recorder (Edr)
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Warning Light NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint You will want to have the air bags ready to Controller (ORC) may also be disabled. The air bags may inflate for your protection in a collision.
Page 55: Child Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 • How various systems in your vehicle were operating; To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. • Whether or not the driver and passenger safety belts In addition to the vehicle manufacturer, other parties, were buckled/fastened;...
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are different sizes and types of restraints for WARNING! children from newborn size to the child almost large enough for an adult safety belt. Always check the child In a collision, an unrestrained child can become a seat Owner’s Manual to make sure you have the correct projectile inside the vehicle.
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight or Age Recommended Type of Child Restraint Infants and Toddlers Children who are two years old or younger Either an Infant Carrier or a Convert- and who have not reached the height or ible Child Restraint, facing rearward weight limits of their child restraint...
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints Children should remain rearward-facing until they reach the highest weight or height allowed by their convertible Safety experts recommend that children ride rearward- child seat. facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear WARNING! facing child safety seat.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 convertible child seats used in the forward-facing direc- WARNING! tion are for children who are over two years old or who • Improper installation can lead to failure of an have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seatback, should use the seat belt in a rear seat. Use this 4. Is the lap part of the belt as low as possible, touching simple 5-step test to decide whether the child can use the the child’s thighs and not their stomach? vehicle’s seat belt alone: 5.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Recommendations For Attaching Child Restraints Restraint Type Combined Use any attachment method shown with an “X” Below Weight of the LATCH – Seat Belt Only LATCH – Seat Belt + Top Child + Child Lower Anchors Lower Anchors Tether Anchor...
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors and Tethers for Children (LATCH) Your vehicle is equipped with the child restraint anchor- Restraint System age system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCH- equipped child seats.
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 • LATCH Positions For Installing Child Restraints In Lower Anchorage Symbol 2 anchorages per seat- This Vehicle ing position • Top Tether Anchorage Symbol...
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE What is the weight limit (child’s weight + 65 lbs (29.5 kg) Use the LATCH anchorage system until weight of the child restraint) for using the the combined weight of the child and the LATCH anchorage system to attach the child restraint is 65 lbs (29.5 kg).
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Can two child restraints be attached us- Never “share” a LATCH anchorage with ing a common lower LATCH anchorage? two or more child restraints. If the center position does not have dedicated LATCH lower anchorages, use the seat belt to install a child seat in the center position next to a child seat using the LATCH...
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint.
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 LATCH-compatible child restraint systems will be To Install A LATCH-compatible Child Restraint equipped with a rigid bar or a flexible strap on each side. 1. If the selected seating position has a Switchable Auto- Each will have a hook or connector to attach to the lower matic Locking Retractor (ALR) seat belt, stow the seat anchorage and a way to tighten the connection to the...
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Attach the lower hooks or connectors of the child How To Stow An Unused ALR Seatbelt restraint to the lower anchorages in the selected seat- When using the LATCH attaching system to install a ing position.
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 the seat belt tight around the child restraint so that it is WARNING! not necessary to use a locking clip. The ALR retractor can be “switched” into a locked mode by pulling all of the Improper installation of a child restraint to the webbing out of the retractor and then letting the webbing LATCH anchorages can lead to failure of the re-...
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle...
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 What is the weight limit (child’s weight Weight limit of the Child Always use the tether anchor when us- + weight of the child restraint) for using Restraint ing the seat belt to install a forward the Tether Anchor with the seat belt to facing child restraint, up to the recom- attach a forward facing child restraint?
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing A Child Restraint with a Switchable 5. To lock the seat belt, pull down on the shoulder part of Automatic Locking Retractor (ALR) the belt until you have pulled all the seat belt webbing out of the retractor.
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 8. If the child restraint has a top tether strap and the Installing A Child Restraint With A Cinching seating position has a top tether anchorage, connect Latch Plate (CINCH) — If Equipped the tether strap to the anchorage and tighten the tether 1.
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. If the child restraint has a top tether strap and the facing out, away from the child restraint. Repeat steps 4 seating position has a top tether anchorage, connect to 6, above, to complete the installation of the child the tether strap to the anchorage and tighten the tether restraint.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts.
Page 76: Transporting Pets
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS WARNING! A long break-in period is not required for the engine and • An incorrectly anchored tether strap could lead to drivetrain (transmission and axle) in your vehicle. increased head motion and possible injury to the Drive moderately during the first 300 miles (500 km).
Page 77: Safety Tips
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 CAUTION! WARNING! • Do not leave children or animals inside parked Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. vehicles in hot weather. Interior heat build-up may cause serious injury or death.
Page 78: Exhaust Gas
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! (Continued) • If it is necessary to sit in a parked vehicle with the WARNING! engine running, adjust your heating or cooling Exhaust gases can injure or kill. They contain carbon controls to force outside air into the vehicle.
Page 79: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Safety Checks You Should Make Inside The not lit during starting, see your authorized studio. If the Vehicle light stays on, flickers, or comes on while driving, have the system checked by an authorized studio. Seat Belts Defroster Inspect the belt system periodically, checking for cuts,...
Page 80 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Check mounting of mats on a regular basis. Always Pedals that cannot move freely can cause loss of properly reinstall and secure floor mats that have vehicle control and increase the risk of serious per- been removed for cleaning.
Page 81: Periodic Safety Checks You Should Make Outside
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Periodic Safety Checks You Should Make Outside Door Latches The Vehicle Check for positive closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
Page 83: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS POWER CONVERTIBLE TOP — IF EQUIPPED . .84 Heated Mirrors — If Equipped ... .90 Lowering The Power Top....85 Sun Visors .
Page 84 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EZ Entry Feature ..... .101 Lane Change Assist ....109 Memory Feature .
Page 85 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 To Vary The Speed Setting ....118 Wind Buffeting ..... . .126 To Accelerate For Passing .
Page 86: Power Convertible Top - If Equipped
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER CONVERTIBLE TOP — IF EQUIPPED On vehicles equipped with a power convertible top, the power convertible top switch is located on the overhead console. The switch contains two buttons. The passenger side button, which is used to open the power top, and the driver side button, which is used to close the power top.
Page 87: Lowering The Power Top
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Lowering The Power Top CAUTION! Press the top open button approximately one second for Failure to follow these cautions may cause interior the partially open position. Press the top open button for water damage, stains or mildew on the top material: approximately one second a second time to fully open the •...
Page 88: Power Convertible Top Relearn Procedure
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Hold the OPEN button to move the top to the fully WARNING! open position. The convertible top does not provide the structural 4. CONTINUE to hold the OPEN button for an addi- protection that a reinforced metal roof does and the tional three seconds.
Page 89: Wind Stop
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Auto Open/Close will now be functional. Trunk lid Headlight glare from vehicles behind you can be reduced operation will be functional. by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror NOTE: DO NOT interrupt this activity.
Page 90: Automatic Dimming Mirror - If Equipped
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated.
Page 91: Power Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Power Mirrors The power mirror controls consist of a mirror select switch and a four-way mirror control switch. To adjust a The power mirror controls are located on the driver’s mirror, press the mirror select switch to either the L (left) door trim panel.
Page 92: Folding Mirrors
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Spotter Mirror — If Equipped Folding Mirrors Some models are equipped with a driver’s side spotter The exterior mirrors are hinged to allow the mirror to mirror. The spotter mirror allows for a greater range of pivot forward or rearward to help avoid damage.
Page 93: Sun Visors
The sun visor can be Overview rotated downward or up against the door glass. Both sun Windows Mobile™-based FIAT BLUE&ME™ is a per- visors are equipped with courtesy mirrors. sonal telematic system enabling you to use communica- tion and entertainment applications expressly designed for use in the car.
Page 94: The Hands-Free Kit
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE you are not required to train the voice recognition system The Hands-Free Kit to recognize your voice. This implies that the system is The basic characteristic of this hands-free kit is voice nearly equally performing with different persons, i.e.: the recognition with Bluetooth wireless technology.
Page 95 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 your mobile phone manually and visually using the For further details on the mobile phones supported by steering wheel controls and the instrument panel multi- BLUE&ME™, refer to section BLUE&ME™ SUPPORTED function display. MOBILE PHONES.
Page 96 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE list or directly pronouncing the phone number, to (LAST CALLS and PHONEBOOK ) and the media answer a call and also to answer another incoming player. To activate settings when travelling you can only phone call.
Page 97 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • To Answer A Call — you can answer an incoming call After pairing and connecting your phone with the by pressing the MENU/Phone button on the steering BLUE&ME™ system, you can make phone calls by wheel.
Page 98 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To call the SMS text sender using the buttons on the NOTE: Not all mobile phones support the SMS text message reader function or automatic phonebook trans- steering wheel or voice commands. fer via Bluetooth .
Page 99 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 In this way, while you are driving you can play your NOTE: favorite music collections. • The media player does not support audio files com- • iPod Player — see dedicated paragraph under Media pressed with other formats and DRM (Digital Right Player Functions.
Page 100: Seats
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Keep the User’s Guide in the car: when kept in the • Operating certain parts of this system while driv- car, the User’s Guide will be a ready reference for ing can distract your attention away from the road, you and other users unfamiliar with the system.
Page 101: Front Seats Forward/Rearward Adjustment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. •...
Page 102: Recline Adjustment
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked.
Page 103: Seat Height Adjustment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Seat Height Adjustment EZ Entry Feature The driver’s seat height can be raised or lowered by The driver and front passenger seats have an EZ entry using a lever, located on the outboard side of the seat. feature for rear seat passengers.
Page 104: Memory Feature
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lift the seatback upright and push the seat rearward to fore/aft (memory) position on the tracks. This results in its locked position once the rear passengers are seated. the seat back memory being set only – The track will then be locked forward of its last set fore/aft memory posi- Memory Feature tion.
Page 105: Head Restraints
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Head Restraints WARNING! Head restraints are designed to reduce the risk of injury • Persons who are unable to feel pain to the skin by restricting head movement in the event of a rear- because of advanced age, chronic illness, diabetes, impact.
Page 106: To Open And Close The Hood
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE downward on the head restraint. Refer to “Occupant TO OPEN AND CLOSE THE HOOD Restraints” in “Things To Know Before Starting Your To open the hood, two latches must be released. Vehicle” for information on tether routing. 1.
Page 107 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Hood Safety Latch Location Hood Prop Rod Lift the hood prop rod that clips to the right side (left side In hot climates, the prop rod may be hot. Pick up the prop when standing in front of the hood) of the engine rod at the foam on the end of the prop rod.
Page 108: Lights
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS WARNING! Multifunction Lever Be sure the hood is fully latched before driving your The multifunction lever, located on the left side of the vehicle. If the hood is not fully latched, it could open steering wheel, controls the operation of the headlights, when the vehicle is in motion and block your vision.
Page 109: High Beams
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 High Beams With the low beams activated, push the multi- function lever towards the instrument panel to turn on the high beams. Pull the multifunction lever toward the steering wheel to turn off the high beams. Flash-To-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward the steer-...
Page 110: Daytime Running Lights - If Equipped
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights — If Equipped To activate the Daytime Running Lights (DRL), rotate the end of the multifunction lever to the O symbol. NOTE: The low beams and side/taillights will not be on with DRL.
Page 111: Lane Change Assist
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Lane Change Assist Deactivation Tap the lever up or down once, without moving beyond Pull the multifunction lever toward the steering wheel the detent, and the turn signal (right or left) will flash and hold it for more than two seconds.
Page 112 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When the doors are unlocked with Key Fob a 10 CAUTION! second timer is activated. Before getting out of the vehicle be sure that the • When the doors are locked with the Key Fob the lights switch is in the center position or that the lights are will turn off.
Page 113: Front Fog Lights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Front Fog Lights — If Equipped WINDSHIELD WIPERS AND WASHERS The fog light switch is located on the center stack of the The windshield wiper/washer lever is located on the instrument panel, just below the radio. right side of the steering column.
Page 114: Front Windshield Wiper Operation
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Windshield Wiper Operation Windshield Wiper Off There are five different modes of operation for the front This is the normal position of the wiper lever. windshield wipers. The windshield wiper lever can be Intermittent Wiper Operation raised or lowered to access these modes: Push the lever downward to the first detent.
Page 115 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Manual High Speed/Mist CAUTION! Push the lever upward from the off position. The wipers • Turn the windshield wipers off when driving will operate at high speed to clear off road mist or spray through an automatic car wash.
Page 116: Rear Windshield Wiper
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Windshield Wiper Rotate the end of the windshield wiper/washer lever upward to the first detent past the intermittent settings for intermittent wipe operation. With the front wind- shield wiper active, rotate the end of the windshield wiper/washer lever upward.
Page 117: Tilt Steering Column - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Rear Windshield Washer Operation Push the windshield wiper/washer lever toward the instrument panel to activate the rear washer. Push and hold the lever for more than a half second and the wipers will activate automatically for three cycles after the lever is released.
Page 118: Electronic Speed Control
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
Page 119: To Activate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 NOTE: In order to ensure proper operation, the Elec- WARNING! tronic Speed Control system has been designed to shut down if multiple Speed Control functions are operated at Leaving the Electronic Speed Control system on the same time.
Page 120: To Deactivate
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate Pressing the RES (+) button once will result in a 1 mph (1.6 km/h) increase in set speed. Each subsequent tap of A soft tap on the brake pedal, pushing the CANC button, the button results in an increase of 1 mph (1.6 km/h).
Page 121: Rear Park Assist - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Using Electronic Speed Control On Hills REAR PARK ASSIST — IF EQUIPPED The transmission may downshift on hills to maintain the The Rear Park Assist system provides an audible indica- vehicle set speed. tion of the distance between the rear fascia/bumper and a detected obstacle when backing up, e.g.
Page 122: Rear Park Assist Sensors
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Park Assist Sensors Rear Park Assist Alerts The four Rear Park Assist sensors, located in the rear If an obstacle is behind the vehicle when REVERSE gear fascia/bumper, monitor the area behind the vehicle that is engaged, an audible alert is activated.
Page 123 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Audible And Visual Signals Supplied By The Rear Park Assist System SIGNAL MEANING INDICATION Obstacle Distance An obstacle is present within Audible signal (dashboard loudspeaker) • Sound pulses emitted at a rate that in- the sensors’...
Page 124: Failure Indications
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Failure Indications Cleaning The Rear Park Assist System A malfunction of the Rear Park Assist sensors or system Clean the Rear Park Assist sensors with water, car wash is indicated, during REVERSE gear engagement, by the soap and a soft cloth.
Page 125 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 • Clean the Rear Park Assist sensors regularly, taking CAUTION! care not to scratch or damage them. The sensors must • Rear Park Assist is only a parking aid and it is not be covered with ice, snow, slush, mud, dirt or debris.
Page 126 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Before using the Rear Park Assist system, it is • Drivers must be careful when backing up even strongly recommended that the ball mount and when using the Rear Park Assist system. Always hitch ball assembly is disconnected from the ve- check carefully behind your vehicle, look behind hicle when the vehicle is not used for towing.
Page 127: Power Sunroof - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof roof switch is located in the overhead • Never leave children in a vehicle with the key in console. the ignition switch (or with the ignition in the Accessory or Run position, for vehicles equipped with Keyless Enter-N-Go™).
Page 128: To Open
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Open Pinch Protect Feature Press and hold the power sunroof switch rearward for This feature will detect an obstruction in the opening of approximately one second and the sunroof will stop at the sunroof during Express Close operation.
Page 129: Emergency Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Emergency Operation In case of electrical failure the sunroof can be operated with the hex wrench that is located in the glove box. There is a plug located in the rear of the sunroof opening at the center of the vehicle.
Page 130: Electrical Power Outlets
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS Power is available when the ignition switch is in the ON/RUN or START position. Insert the cigar lighter or There is a standard 12 Volt (13 Amp) power outlet, accessory plug into the outlet for use. To preserve the located in the floor console, for added convenience.
Page 131 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. •...
Page 132: Cigar Lighter - If Equipped
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER — IF EQUIPPED CAUTION! • Many accessories that can be plugged in draw WARNING! power from the vehicle’s battery, even when not in When the cigar lighter is in use it becomes very hot. To use (i.e., cellular phones, etc.).
Page 133: Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 CUPHOLDERS For rear passengers, there are cupholders located on the floor between the front driver and passenger seats. For the driver and front passenger, cupholders are lo- cated on the floor console between the front seats. Rear Cupholders Front Cupholders...
Page 134: Storage
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE CARGO AREA FEATURES The rear seatbacks have a fold down feature to allow Glove Box Compartment increased cargo capacity. The glove box is located on the right side of the instru- ment panel. Pull outward on the door latch to open the Push down the release button, located at the outboard glove box.
Page 135 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Rear Seat Release Buttons Folded Rear Seats...
Page 136: Rear Window Features
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES CAUTION! Rear Window Defroster Failure to follow these cautions can cause damage to The rear window defroster button is located in the the heating elements: center of the instrument panel, below the radio. •...
Page 137 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT PANEL FEATURES ..137 Trip Computer ..... . .155 TURBO BOOST GAUGE .
Page 138 136 UNDERSTANDING YOUR INSTRUMENT PANEL Quick Guide ......172 CD Player Operation ....196 General Information.
Page 139: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 137 INSTRUMENT PANEL FEATURES 1 — Side Vent 7 — Passenger Air Bag 13 — Storage Compartment 2 — Multifunction Lever – Light Control 8 — Glove Compartment 14 — Shift Lever 3 — Instrument Cluster And Warning Lights 9 —...
Page 140: Turbo Boost Gauge
138 UNDERSTANDING YOUR INSTRUMENT PANEL TURBO BOOST GAUGE Your vehicle is equipped with a boost gauge and inte- grated shift light indicator located to the left of the instrument cluster. The boost gauge indicates the intake manifold pressure relative to barometric pressure. The engine management system in your vehicle intelligently regulates intake manifold pressure based on environ- mental (ambient) and engine operating conditions.
Page 141: Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 139 INSTRUMENT CLUSTER...
Page 142: Instrument Cluster Descriptions
140 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 2. Rear Defrost Button 1. Glow Plug Light — If Equipped Press and release this button to turn on the rear window defroster. This indicator will illuminate The Glow Plug light will flash during engine oil when the rear window defroster is on.
Page 143 UNDERSTANDING YOUR INSTRUMENT PANEL 141 6. Park/Headlight ON Indicator / Follow Me Home CAUTION! (Continued) (Headlight Delay) Indicator — If Equipped • Do not use scrapers, sharp instruments, or abrasive This indicator will illuminate when the park window cleaners on the interior surface of the lights or headlights are turned on.
Page 144 142 UNDERSTANDING YOUR INSTRUMENT PANEL 8. Generic Warning Light 10. Cruise Indicator — If Equipped The Generic Warning Light will illuminate if This indicator shows that the Speed Control any of the following conditions occur: Oil system is on. Change Request, Engine Oil Pressure Sensor Failure, External Light Failure, Fuel Cut-Off 11.
Page 145 UNDERSTANDING YOUR INSTRUMENT PANEL 143 12. Charging System Light 14. Electronic Throttle Control (ETC) Light This light shows the status of the electrical charg- This light informs you of a problem with the ing system. The light should come on when the Electronic Throttle Control (ETC) system.
Page 146 144 UNDERSTANDING YOUR INSTRUMENT PANEL 15. Tire Pressure Monitoring Telltale Light reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Each tire, including the spare (if provided), Please note that the TPMS is not a substitute for proper should be checked monthly when cold and tire maintenance, and it is the driver’s responsibility to inflated to the inflation pressure recommended...
Page 147 UNDERSTANDING YOUR INSTRUMENT PANEL 145 alternate tires or wheels on the vehicle that prevent the 16. Automatic Gearbox Failure TPMS from functioning properly. Always check the This light will illuminate when there is an TPMS malfunction telltale after replacing one or more automatic transmission fault.
Page 148 146 UNDERSTANDING YOUR INSTRUMENT PANEL 18. Malfunction Indicator Light (MIL) CAUTION! The Malfunction Indicator Light (MIL) is part of Prolonged driving with the MIL on could cause an onboard diagnostic system, called OBDII, that damage to the engine control system. It also could monitors engine and automatic transmission con- affect fuel economy and drivability.
Page 149 UNDERSTANDING YOUR INSTRUMENT PANEL 147 19. Engine Temperature Warning Light 20. Brake Warning Light This light warns of an overheated engine condi- This light monitors various brake functions, tion. The engine coolant temperature indicator including brake fluid level and parking brake will illuminate and a single chime will sound after application.
Page 150 148 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicles equipped with the Anti-Lock Brake System 21. Electronic Stability Control OFF (ESC OFF) Indica- (ABS), are also equipped with Electronic Brake Force tor Light Distribution (EBD). In the event of an EBD failure, the This light indicates the Electronic Stability Con- Brake Warning Light will turn on along with the ABS trol system (ESC) has been turned off by the...
Page 151 UNDERSTANDING YOUR INSTRUMENT PANEL 149 NOTE: If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock The ESC Off Indicator Light and the ESC Activation/ brakes. If the ABS light does not turn on when the Malfunction Indicator Light come on momentarily each ignition switch is turned to the ON/RUN position, have time the ignition switch is turned to ON/RUN.
Page 152 150 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! WARNING! (Continued) Vehicle.” Follow the warnings under the “Cooling Driving with a hot engine cooling system could System Pressure Cap” paragraph. damage your vehicle. If the temperature gauge reads “280“, pull over and stop the vehicle. Idle the vehicle 26.
Page 153 UNDERSTANDING YOUR INSTRUMENT PANEL 151 service, so that you can be sure that it is properly reset, or NOTE: The fuel gauge and range will not immediately that the door jamb sticker is accurate if the odometer update accurately when refueling with the engine on. must be reset at zero.
Page 154: Electronic Vehicle Information Center (Evic)
152 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER The EVIC consists of the following: (EVIC) • System Status The Electronic Vehicle Information Center (EVIC) fea- • Vehicle Information Warning Message Displays tures a driver-interactive display that is located in the •...
Page 155: Electronic Vehicle Information Center (Evic) Setup Menu
UNDERSTANDING YOUR INSTRUMENT PANEL 153 Press the DOWN button to scroll downward through The setup menu can be activated by pressing the SET the displayed menu and the related options or to de- ESC button. Single presses on the UP or DOWN crease the value displayed.
Page 156 154 UNDERSTANDING YOUR INSTRUMENT PANEL • Button Volume Selecting An Option Of The Main Menu With Sub- menu • Hill Start 1. Briefly press the SET ESC button to display the first • GSI Shift Up submenu option. • Daylights (D.R.L.) 2.
Page 157: Change Engine Oil Indicator System
UNDERSTANDING YOUR INSTRUMENT PANEL 155 6. Press and hold the SET ESC button to return to the indicator system (after performing the scheduled main- main menu (short hold) or the main screen (longer tenance), refer to the following procedure. hold). 1.
Page 158: Trip Button
156 UNDERSTANDING YOUR INSTRUMENT PANEL Trip Button NOTE: If the reset operation occurs in the presence of the screens concerning Trip A or Trip B, only the infor- The TRIP button, located on the right steering column mation associated with Trip A or Trip B functions will be stalk, can be used to display and to reset the previously reset.
Page 159: Trip Functions
UNDERSTANDING YOUR INSTRUMENT PANEL 157 Trip Functions NOTE: “Trip B” functions may be excluded (see “Trip B Data”). “Range” and “Instantaneous consumption” can- Both trip functions are resettable (reset — start of new not be reset. trip). Values Displayed “Trip A” can be used to display the figures relating to: •...
Page 160: Personal Settings (Customer-Programmable Features)
158 UNDERSTANDING YOUR INSTRUMENT PANEL Distance Travelled Personal Settings (Customer-Programmable Features) This value shows the distance covered since the last reset. Dimmer Average Consumption The EVIC display is provided with a light sensor capable This value shows the approximate average consumption of detecting environmental light conditions and adjust- since the last reset.
Page 161 UNDERSTANDING YOUR INSTRUMENT PANEL 159 2. Briefly press the SET ESC button to go back to the 3. When the function is activated (On), briefly press the menu screen or press and hold the SET ESC (approxi- SET ESC button to display the presently set activation mately one second) to go back to the main screen speed.
Page 162 160 UNDERSTANDING YOUR INSTRUMENT PANEL To cancel the setting, proceed as follows: For activation / deactivation, proceed as follows: 1. Briefly press the SET ESC button. “On” will flash on 1. Briefly press the SET ESC button. “On” or “Off” will the display.
Page 163 UNDERSTANDING YOUR INSTRUMENT PANEL 161 Proceed as follows: NOTE: • The setting will increase or decrease by one unit each 1. Briefly press the SET ESC button. The display will show the two sub-menu items “Time” and “Mode.” time the UP or DOWN button is pressed.
Page 164 162 UNDERSTANDING YOUR INSTRUMENT PANEL sub-menu screen, or press and hold the SET ESC button 6. Press the UP or DOWN button for setting. (approximately one second) to go back to the main screen NOTE: The setting will increase or decrease by one unit without storing the settings.
Page 165 UNDERSTANDING YOUR INSTRUMENT PANEL 163 To activate (On) or to deactivate (Off) the sound system To activate (On) or to deactivate (Off) the speed display info displaying proceed as follows: feature, proceed as follows: 1. Briefly press the SET ESC button “On” or “Off” will 1.
Page 166 164 UNDERSTANDING YOUR INSTRUMENT PANEL To change the setting proceed as follows: 2. Press the UP or DOWN button to navigate the three sub-menus. 1. Briefly press the SET ESC button “On” or “Off” will flash on the display (according to the previous set- 3.
Page 167 UNDERSTANDING YOUR INSTRUMENT PANEL 165 If the distance unit set is “km,” the fuel economy unit will or press and hold the SET ESC button (approximately be displayed in either km/l or l/100km. one second) to go back to the main screen without storing the settings.
Page 168 (approximately one second) to go back to the main screen without storing the settings. screen without storing the settings. Belt Buzzer (Buzzer Activation For S.B.R. Indication) This function will only be displayed after a FIAT Group Automobiles dealer has deactivated the S.B.R. system.
Page 169 UNDERSTANDING YOUR INSTRUMENT PANEL 167 Hill Start Assist GSI Shift Up This function is used when starting a vehicle from a stop With this function active, the boost gauge will display a on a hill. Hill Start Assist maintains the same level of shift up message and up arrow at the appropriate time of brake pressure the driver applied for a short period of shift.
Page 170 168 UNDERSTANDING YOUR INSTRUMENT PANEL Proceed as follows to switch this function on or off: Exit Menu This function closes the initial menu screen. 1. Briefly press the SET ESC button to display the three sub-menus. Briefly press the SET ESC button to go back to the main screen.
Page 171: Sales Code (Rab) Radio
UNDERSTANDING YOUR INSTRUMENT PANEL 169 SALES CODE (RAB) RADIO If the radio has BLUE&ME™, refer to the appropriate “BLUE&ME™ User’s Manual” for further information. The instructions for use are given below and we recom- mend you to read them carefully. Suggestions Road Safety Please, learn how to use all different radio functions (e.g.
Page 172 170 UNDERSTANDING YOUR INSTRUMENT PANEL • Clean every CD thoroughly removing any finger WARNING! marks or dust using a soft cloth. Hold CDs by the outside and clean them from the middle outwards. Having the volume turned up high can cause the driver to not be able to hear important traffic sounds, •...
Page 173: Technical Specifications
UNDERSTANDING YOUR INSTRUMENT PANEL 171 • The use of original CD media is required for the best • The CD player is capable of reading most compression quality audio production. Correct operation is not systems currently in use, following the development of guaranteed when CD-R/RW media are used that were these systems, the reading of all compression formats not correctly burned and/or with a maximum capacity...
Page 174: Understanding Your Instrument Panel
172 UNDERSTANDING YOUR INSTRUMENT PANEL • A subwoofer under the right front seat. With Bose Premium Audio system (if equipped): • Two 165 mm diameter midwoofer speakers. • An amplifier in the trunk on the right-hand side panel. • Two 11 mm tweeter speakers in the front pillars. •...
Page 175 UNDERSTANDING YOUR INSTRUMENT PANEL 173 BUTTON GENERAL FUNCTIONS MODE (Mute/Pause Button) Volume activation/deactivation Short button press (Mute/Pause) AUDIO Audio adjustments: low tones (BASS), high Menu activation: short button press tones (TREBLE), left/right balance Adjustment type selection: press (BALANCE), front/rear balance (FADER) Adjustment of values: press (Information Button) Song, Artist, Album, Genre, Playlist, Folder...
Page 176 174 UNDERSTANDING YOUR INSTRUMENT PANEL BUTTON RADIO FUNCTIONS MODE Radio Station Search: Automatic search: press buttons • Automatic Search (long press for fast forward) • Manual Search Manual search: press buttons (long press for fast forward) 1 2 3 4 5 Current radio station storing Long button press for memory preset 1 to 5 respectively...
Page 177: General Information
UNDERSTANDING YOUR INSTRUMENT PANEL 175 General Information CD Section • Track selection (forward/backward) The radio offers the following functions: • Fast forward/rewind through tracks Radio Section • PLL tuning with FM/AM/MW frequency bands • CD Display function: display of track number and on mp3 discs (song title, artist) and time elapsed since •...
Page 178: Functions And Adjustments
176 UNDERSTANDING YOUR INSTRUMENT PANEL • Separate bass/treble tone adjustment CD/MP3 Section • MP3-Info function (ID3-TAG) • Right/left channel balancing • Folder selection (previous/next) • Front/rear fader • Track selection (forward/backward) Functions And Adjustments • Fast forward/rewind through tracks Turning The Car Radio On •...
Page 179 UNDERSTANDING YOUR INSTRUMENT PANEL 177 Selecting The Radio Functions Press the button again to deactivate the MUTE func- tion. The volume will gradually increase until it reaches By pressing the TUNER button briefly and repeatedly, the previously set level. the following audio sources can be selected cyclically: When the volume level is changed using the dedicated •...
Page 180 178 UNDERSTANDING YOUR INSTRUMENT PANEL Use the buttons to scroll through the Menu Tone Adjustment functions. To change the setting of the selected function, Proceed as follows: use the buttons. 1. Press AUDIO button. The current status of the selected function appears on the 2.
Page 181 UNDERSTANDING YOUR INSTRUMENT PANEL 179 3. Press the button to increase the sound from the left By pressing the buttons briefly, the levels will speakers or the button to increase the sound from change progressively. By pressing them down longer, the the right speakers.
Page 182 180 UNDERSTANDING YOUR INSTRUMENT PANEL Preset/User*/Classic/Rock/Jazz Functions — If When one of the equalizer adjustments is activated the Equipped wording “EQ” lights up. The built-in equalizer can be activated/deactivated. *User EQ Settings Function — If Equipped When the equalizer function is off, the audio settings can To set a personalized equalizer adjustment: only be changed by adjusting the “Bass”...
Page 183 UNDERSTANDING YOUR INSTRUMENT PANEL 181 • SiriusXM™ Telephone Number Menu • System Reset MENU Button Functions • Speed Volume Press the MENU button briefly to activate the Menu function. • On Volume Limit Use the buttons to scroll through the menu Press the MENU button again to exit the Menu function.
Page 184 182 UNDERSTANDING YOUR INSTRUMENT PANEL • “On volume limit: off” – The radio will come on at the On Volume Limit same volume as before it was switched off. The This function makes it possible to activate/deactivate the volume level can be between 0 and 40. maximum volume limit when turning the radio on.
Page 185: Radio
UNDERSTANDING YOUR INSTRUMENT PANEL 183 • YES — The default parameters will be restored. Dur- Radio Off Function ing such operation, the wording “Resetting” appears This function makes it possible to set the radio switching on the display. At the end of the operation, the source off mode by choosing between two methods.
Page 186 184 UNDERSTANDING YOUR INSTRUMENT PANEL Frequency Band Selection To listen to a preset station, select the desired frequency band and then briefly press the corresponding preset With the Radio mode active, press the FM or AM tuner button (from 1 to 5). button briefly and repeatedly to select the desired recep- tion band.
Page 187: Siriusxm™ Satellite Radio - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 185 Manual Tuning of sight of the antenna will cause decreased performance. Larger luggage items should be placed as far from the This is used to manually search for stations in the antenna as possible. Do not place items directly on or preselected band.
Page 188 186 UNDERSTANDING YOUR INSTRUMENT PANEL logos are trademarks of SiriusXM™ Radio Inc. and its The Program Types available are: All, Pop, Rock, subsidiaries. SiriusXM™ Radio requires a subscription, Electronic/Dance, Hip-Hop/R&B, Country, Christian, sold separately after trial subscription included with Jazz/Standards, Classical, Latin/World, Sports, Enter- vehicle purchase.
Page 189 Sirius Subscription Issues When Replacing A CAUTION! Sirius Radio Neither SIRIUS nor FIAT is responsible for any When a radio needs to be replaced, the studio will need errors in accuracies in the SIRIUS data services or its the SIRIUS information to order a new radio (even if the use in vehicles.
Page 190: Cd Player
188 UNDERSTANDING YOUR INSTRUMENT PANEL The following are instructions for retrieving the Elec- CD Player Selection tronic Serial Number (ESN) from FIAT 500 NAFTA model To activate the CD player built into the equipment, radios: proceed as follows: To retrieve the ESN of SIRIUS Satellite Receiver Module •...
Page 191 UNDERSTANDING YOUR INSTRUMENT PANEL 189 CD Loading/Ejecting If the CD is not removed from the radio, it will automati- cally be reloaded about 20 seconds later but will not To load the CD, insert it gently into the slot to activate the resume playing until the MEDIA button is pressed to motorized loading system, which will position it cor- select the CD mode.
Page 192: Cd Mp3 Player
190 UNDERSTANDING YOUR INSTRUMENT PANEL Display Information Track Fast Forward/Rewind When the CD player is operating, information will ap- Keep the button pressed down to fast forward the pear on the display with the following meaning: selected track and keep the button pressed down to fast rewind the track.
Page 193 UNDERSTANDING YOUR INSTRUMENT PANEL 191 • The sampling frequencies that can be reproduced are: MP3 Mode 44.1 kHz, stereo (from 96 to 320 kbit/s) – 22.05 kHz, In addition to playing regular audio CDs, the radio is also mono or stereo (from 32 to 80 kbit/s). enabled to play CDROMs on which compressed audio •...
Page 194 192 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: When the function is activated the radio may Selection Of Next/Previous Folder take a few seconds to start playing. While checking the Press the button to select a next folder or the but- disc the display will show “CD Reading.” If no MP3 files ton to select the previous folder.
Page 195: Troubleshooting
UNDERSTANDING YOUR INSTRUMENT PANEL 193 • If the MP3 files on a CD-ROM are structured in CD Player sub-folders their structure is compressed to a single The CD Does Not Play level structure, where the sub-folders are taken to the The CD is dirty.
Page 196: Ipod /Usb/Media Player Control - If
194 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Hands-Free Phone (If Equipped) Refer to the appropriate “BLUE&ME™ User’s Manual” for further information. Personal/Portable Navigation Device (PND) — If Equipped A Personal/Portable Navigation Device (PND) is avail- able as optional equipment for this vehicle, refer to the Navigation User Guide for further information.
Page 197: Steering Wheel Audio Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 195 STEERING WHEEL AUDIO CONTROLS The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and The remote sound system controls are located on the rear mode of the sound system. Pressing the top of the rocker surface of the steering wheel.
Page 198: Radio Operation
196 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation Operating Instructions — Hands-Free Phone (If Equipped) Pressing the top of the switch will “Seek” up for the next listenable station and pressing the bottom of the switch Refer to the appropriate Blue&Me™ User’s Manual for will “Seek”...
Page 199: Radio Operation And Mobile Phones
UNDERSTANDING YOUR INSTRUMENT PANEL 197 5. Store the disc in its case after playing. RADIO OPERATION AND MOBILE PHONES Under certain conditions, the mobile phone being on in 6. Do not expose the disc to direct sunlight. your vehicle can cause erratic or noisy performance from 7.
Page 200: Manual Heating And Air Conditioning
198 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Heating And Air Conditioning 1. Temperature Control Rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial to the left into the blue area of the scale indicates cooler temperatures, while rotating to the right into the red area indicates warmer temperatures.
Page 201 UNDERSTANDING YOUR INSTRUMENT PANEL 199 • Panel NOTE: Air is directed through the outlets in the instru- Continuous use of the Recirculation mode may make the ment panel. These outlets can be adjusted to direct inside air stuffy and window fogging may occur. Ex- airflow.
Page 202 200 UNDERSTANDING YOUR INSTRUMENT PANEL to the windshield. This setting is good for maintaining 5. A/C Button comfort while reducing moisture on the windshield. Press this button to engage the Air Conditioning. A light • Defrost will illuminate when the Air Conditioning system is Air is directed through the windshield and side engaged.
Page 203: Operating Tips Chart
UNDERSTANDING YOUR INSTRUMENT PANEL 201 Operating Tips Chart...
Page 204: Automatic Temperature Control (Atc) - If Equipped
202 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Temperature Control (ATC) — If Equipped • The Automatic Temperature Control (ATC) allows the driver to select individual comfort settings. • The system provides set-and-forget operation for op- timum comfort and convenience. • The system can be controlled manually, if desired. The ATC system automatically maintains the interior comfort level desired by the driver and passenger.
Page 205 UNDERSTANDING YOUR INSTRUMENT PANEL 203 1. AUTO Temperature Control (ATC) Button 4. Blower Control Up Button There are 12 blower speeds. The blower speed increases Controls airflow, temperature, distribution, and air recir- as you press this button. Performing this function will culation automatically.
Page 206 204 UNDERSTANDING YOUR INSTRUMENT PANEL 7. Floor Mode 10. Temperature Control Down Button Air is directed through the floor outlets with a small Provides temperature down control. Push the button for amount flowing through the defrost and side window cooler temperature settings. demister outlets.
Page 207 UNDERSTANDING YOUR INSTRUMENT PANEL 205 Automatic Operation NOTE: • It is not necessary to move the temperature settings for 1. Press the AUTO button on the Automatic Temperature Control (ATC) Panel, the indicator will illuminate cold or hot vehicles. The system automatically adjusts when on.
Page 208 206 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Operation The blower fan speed can be set to any fixed speed by pressing the blower control up or down buttons. The fan This system offers a full complement of manual override will now operate at a fixed speed until additional speeds features.
Page 209 UNDERSTANDING YOUR INSTRUMENT PANEL 207 Floor Mode Defrost Mode Air comes from the floor outlets. A slight amount Air comes from the windshield and side window of air is directed through the defrost and side demister outlets. Use Defrost mode with maxi- window demister outlets.
Page 210 208 UNDERSTANDING YOUR INSTRUMENT PANEL outlets. If Economy mode is desired, press the A/C Recirculation Control button to turn off the A/C mode in the ATC display and When outside air contains smoke, odors, or deactivate the A/C system. high humidity, or if rapid cooling is desired, you may wish to recirculate interior air by NOTE: pressing the RECIRCULATION control button.
Page 211: Operating Tips Chart
UNDERSTANDING YOUR INSTRUMENT PANEL 209 Operating Tips Chart...
Page 212 210 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Summer Operation Windows will fog on the inside when the humidity inside NOTE: In some cases during high temperature opera- the vehicle is high. This often occurs in mild or cool tion, the air conditioning system performance may be temperatures when it’s rainy or humid.
Page 213 UNDERSTANDING YOUR INSTRUMENT PANEL 211 Vacation Storage Anytime you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air using the high blower setting. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the air conditioning system is started again.
Page 215: Starting And Operating
STARTING AND OPERATING CONTENTS STARTING PROCEDURES ....216 Recommended Shift Speeds ....220 Manual Transmission ....216 Downshifting .
Page 216 214 STARTING AND OPERATING SPORT MODE ......227 Tire Identification Number (TIN)...240 BRAKE SYSTEM .
Page 217 STARTING AND OPERATING 215 Tire Spinning ......251 E-85 Usage In Non-Flex Fuel Vehicles ..263 Tread Wear Indicators .
Page 218: Starting Procedures
216 STARTING AND OPERATING STARTING PROCEDURES Manual Transmission Before starting your vehicle, adjust your seat, adjust both Apply the parking brake, place the shift lever in NEU- inside and outside mirrors, and fasten your seat belts. TRAL, and press the clutch pedal before starting the vehicle.
Page 219: Cold Weather Operation
STARTING AND OPERATING 217 Cold Weather Operation Extended Park Starting To prevent possible engine damage while starting at low NOTE: Extended Park condition occurs when the vehicle temperatures, this vehicle will inhibit engine cranking has not been started or driven for at least 35 days. when the ambient temperature is less than –22°...
Page 220: If Engine Fails To Start
218 STARTING AND OPERATING If Engine Fails To Start After Starting The idle speed will automatically decrease as the engine WARNING! warms up. Never pour fuel or other flammable liquid into the Turbocharger “Cool Down” throttle body air inlet opening in an attempt to start This vehicle is equipped with an after-run pump to cool the vehicle.
Page 221: Manual Transmission
STARTING AND OPERATING 219 MANUAL TRANSMISSION Five-Speed Manual Transmission WARNING! You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should al- ways be applied when the driver is not in the vehicle, especially on an incline.
Page 222: Recommended Shift Speeds
220 STARTING AND OPERATING Use each gear in numerical order; do not skip a gear. Be Recommended Shift Speeds sure the transmission is in first gear, not third, when To use your manual transmission for optimal fuel starting from a standing position. Damage to the clutch economy, it should be upshifted as listed in the following can result from starting in third gear.
Page 223: Downshifting
STARTING AND OPERATING 221 Downshifting DRIVING ON SLIPPERY SURFACES Proper downshifting will improve fuel economy and Acceleration prolong engine life. Rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the driving wheels to pull CAUTION! erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under If you skip more than one gear while downshifting the front (driving) wheels.
Page 224: Traction
222 STARTING AND OPERATING Traction DRIVING THROUGH WATER When driving on wet or slushy roads, it is possible for a Driving through water more than a few inches/ wedge of water to build up between the tire and road centimeters deep will require extra caution to ensure surface.
Page 225: Shallow Standing Water
STARTING AND OPERATING 223 Shallow Standing Water CAUTION! (Continued) Although your vehicle is capable of driving through • Driving through standing water may cause damage shallow standing water, consider the following Caution to your vehicle’s drivetrain components. Always and Warning before doing so. inspect your vehicle’s fluids (i.e., engine oil, trans- mission, axle, etc.) for signs of contamination (i.e., CAUTION!
Page 226: Power Steering
224 STARTING AND OPERATING POWER STEERING WARNING! The electric power steering system will give you good • Driving through standing water limits your vehi- vehicle response and increased ease of maneuverability cle’s traction capabilities. Do not exceed 5 mph in tight spaces. The system will vary its assist to provide (8 km/h) when driving through standing water.
Page 227: Parking Brake
STARTING AND OPERATING 225 If the Steering icon is displayed and the “POWER STEER- NOTE: ING SYSTEM OVER TEMP” message is displayed on the • Even if the power steering assistance is no longer EVIC screen, they indicate that extreme steering maneu- operational, it is still possible to steer the vehicle.
Page 228 226 STARTING AND OPERATING The parking brake lever is located in the center console. When the parking brake is applied with the ignition To apply the parking brake, pull the lever up as firmly as switch in the MAR (ACC/ON/RUN) position, the Brake possible.
Page 229: Sport Mode
STARTING AND OPERATING 227 WARNING! (Continued) CAUTION! • Do not leave the key fob in or near the vehicle (or If the Brake Warning Light remains on with the in a location accessible to children), and do not parking brake released, a brake system malfunction leave the ignition in the MAR (ACC/ON/RUN) is indicated.
Page 230: Brake System
228 STARTING AND OPERATING 1. To activate the Sport mode, press the SPORT button. BRAKE SYSTEM In the event power assist is lost for any reason (for example; repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be significantly more than that required with the power system operating.
Page 231 STARTING AND OPERATING 229 The system’s pump motor runs during an ABS stop to WARNING! (Continued) provide regulated hydraulic pressure. The pump motor • The Anti-Lock Brake System (ABS) cannot prevent makes a low humming noise during operation, which is the natural laws of physics from acting on the normal.
Page 232: Electronic Brake Control System
230 STARTING AND OPERATING When you are in a severe braking condition involving the Anti-Lock Brake System (ABS) use of the ABS, you will experience some pedal drop as This system aids the driver in maintaining vehicle control the vehicle comes to a stop. This is the result of the under adverse braking conditions.
Page 233: Traction Control System (Tcs)
STARTING AND OPERATING 231 benefit of the system, you must apply continuous brak- Traction Control System (TCS) ing pressure during the stopping sequence (do not This system monitors the amount of wheel spin of each of “pump” the brakes). Do not reduce brake pedal pressure the driven wheels.
Page 234 232 STARTING AND OPERATING period of time after the driver takes his foot off the brake WARNING! pedal. If the driver does not apply the throttle during this short period of time, the system will release brake There may be situations on minor hills (i.e., less than pressure and the vehicle will roll down the hill.
Page 235: Electronic Stability Control (Esc)
STARTING AND OPERATING 233 Electronic Stability Control (ESC) This system enhances directional control and stability of the vehicle under various driving conditions. ESC cor- rects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the oversteering or understeering condi- tion.
Page 236 234 STARTING AND OPERATING Full On WARNING! This is the normal operating mode for ESC. Whenever The Electronic Stability Control (ESC) cannot prevent the vehicle is started, the ESC system will be in On mode. the natural laws of physics from acting on the vehicle, This mode should be used for most driving situations.
Page 237: Esc Activation/Malfunction Indicator Light And Esc Off Indicator Light
STARTING AND OPERATING 235 WARNING! WARNING! When in “Partial Off” mode, the TCS functionality of In the ESC “Full Off” mode, the engine torque ESC (except for the limited slip feature described in reduction and stability features are cancelled. There- the TCS section) has been disabled and the “ESC Off fore, the enhanced vehicle stability offered by ESC is Indicator Light”...
Page 238 236 STARTING AND OPERATING driven several miles (kilometers) at speeds greater than NOTE: 30 mph (48 km/h), see your authorized studio as soon as • The ESC Activation/Malfunction Indicator Light and possible to have the problem diagnosed and corrected. the ESC OFF Indicator Light come on momentarily The ESC Activation/Malfunction Indicator Light (located each time the ignition switch is turned ON.
Page 239: Tire Safety Information
STARTING AND OPERATING 237 TIRE SAFETY INFORMATION NOTE: Tire Markings • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
Page 240 238 STARTING AND OPERATING • High flotation tire sizing is based on U.S. design Tires designed to this standard have the letter “T” or “S”molded into the sidewall preceding the size desig- standards and it begins with the tire diameter molded nation.
Page 241 STARTING AND OPERATING 239 EXAMPLE: 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 242: Tire Identification Number (Tin)
240 STARTING AND OPERATING Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on The TIN may be found on one or both sides of the tire, the outboard side, then you will find it on the inboard however, the date code may only be on one side.
Page 243: Tire Terminology And Definitions
STARTING AND OPERATING 241 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after Cold Tire Inflation Pressure the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
Page 244: Tire Loading And Tire Pressure
242 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry Tire Placard Location...
Page 245 STARTING AND OPERATING 243 To determine the maximum loading conditions of your 3) tire size designed for your vehicle vehicle, locate the statement “The combined weight of 4) cold tire inflation pressures for the front, rear, and occupants and cargo should never exceed XXX lbs or spare tires.
Page 246 244 STARTING AND OPERATING 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • The following table shows examples on how to calcu- “XXX” amount equals 1,400 lbs (635 kg) and there will late total load, cargo/luggage, and towing capacities be five 150 lb (68 kg) passengers in your vehicle, the of your vehicle with varying seating configurations...
Page 247 STARTING AND OPERATING 245...
Page 248: Tires - General Information
246 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
Page 249: Tire Inflation Pressures
STARTING AND OPERATING 247 Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the • Unequal tire pressures from one side of the vehicle driver’s side B-Pillar. to the other can cause the vehicle to drift to the right or left.
Page 250: Tire Pressures For High Speed Operation
248 STARTING AND OPERATING Inflation pressures specified on the placard are always inflation pressure should be increased by 3 psi (21 kPa), cold tire inflation pressure. Cold tire inflation pressure is which equals 1 psi (7 kPa) for every 12° F (7° C) for this defined as the tire pressure after the vehicle has not been outside temperature condition.
Page 251: Radial Ply Tires
STARTING AND OPERATING 249 Cuts and punctures in radial tires are repairable only in WARNING! the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs. High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your All Season Tires –...
Page 252: Summer Or Three Season Tires - If Equipped
250 STARTING AND OPERATING If you need snow tires, select tires equivalent in size and Summer Or Three Season Tires – If Equipped type to the original equipment tires. Use snow tires only Summer tires provide traction in both wet and dry in sets of four;...
Page 253: Tire Spinning
STARTING AND OPERATING 251 If your vehicle is not equipped with an original equip- Tire Spinning ment tire and wheel as a spare, a non-matching tempo- When stuck in mud, sand, snow, or ice conditions, do not rary emergency use spare may be equipped with your spin your vehicle’s wheels above 30 mph (48 km/h) or vehicle.
Page 254: Tread Wear Indicators
252 STARTING AND OPERATING Tread Wear Indicators These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth Tread wear indicators are in the original equipment tires becomes 1/16 in (2 mm). When the tread is worn to the to help you in determining when your tires should be tread wear indicators, the tire should be replaced.
Page 255: Replacement Tires
STARTING AND OPERATING 253 “Tread Wear Indicators”). Refer to the “Tire and Loading WARNING! Information” placard for the size designation of your tire. The Load Index and Speed Symbol for your tire will be Tires and the spare tire should be replaced after found on the original equipment tire sidewall.
Page 256 254 STARTING AND OPERATING WARNING! WARNING! (Continued) • Never use a tire with a smaller load index or • Do not use a tire, wheel size or rating other than capacity, other than what was originally equipped that specified for your vehicle. Some combinations on your vehicle.
Page 257: Tire Chains (Traction Devices)
STARTING AND OPERATING 255 TIRE CHAINS (TRACTION DEVICES) These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with Due to limited clearance, tire chains or traction devices aggressive tread designs such as those on all season type are not recommended.
Page 258: Tire Pressure Monitoring System (Tpms)
256 STARTING AND OPERATING The suggested rotation method is the “rearward cross” TIRE PRESSURE MONITORING SYSTEM (TPMS) shown in the following diagram. This rotation pattern The Tire Pressure Monitor System (TPMS) will warn the does not apply to some directional tires that must not be driver of a low tire pressure based on the vehicle recom- reversed.
Page 259 STARTING AND OPERATING 257 The TPMS will warn the driver of a low tire pressure if For example, your vehicle may have a recommended the tire pressure falls below the low pressure warning cold (parked for more than three hours) tire pressure of limit for any reason, including low temperature effects, or 30 psi (207 kPa).
Page 260 258 STARTING AND OPERATING NOTE: CAUTION! • The TPMS is not intended to replace normal tire care • The TPMS has been optimized for the original and maintenance, or to provide warning of a tire equipment tires and wheels. TPMS pressures and failure or condition.
Page 261: Base System
STARTING AND OPERATING 259 • Seasonal temperature changes will affect tire pressure, The TPMS consists of the following components: and the TPMS will monitor the actual tire pressure in • Receiver Module the tire. • Four Tire Pressure Monitoring Sensors Base System •...
Page 262 260 STARTING AND OPERATING Check TPMS Warnings 3. Snow or ice around the wheels or wheel housings. The Tire Pressure Monitoring Telltale Light will flash on 4. Using tire chains on the vehicle. and off for 75 seconds and remain on solid when a system 5.
Page 263 STARTING AND OPERATING 261 3. However, after driving the vehicle for up to 20 min- 5. Once you repair or replace the original road tire and utes above 15 mph (24 km/h), the Tire Pressure reinstall it on the vehicle in place of the compact spare Monitoring Telltale Light will flash on and off for tire, the TPMS will update automatically and the Tire 75 seconds and then remain on solid and the Tire...
Page 264: General Information
262 STARTING AND OPERATING General Information FUEL REQUIREMENTS This device complies with Part 15 of the FCC rules and This engine is designed to meet all emis- RSS 210 of Industry Canada. Operation is subject to the sion regulations and provide satisfactory following conditions: fuel economy and performance when us- ing high-quality unleaded “regular”...
Page 265: Reformulated Gasoline
STARTING AND OPERATING 263 Reformulated Gasoline CAUTION! Many areas of the country require the use of cleaner Do not use gasoline containing Methanol or E-85 burning gasoline referred to as “Reformulated Gasoline.” Ethanol. Use of these blends may result in starting Reformulated gasolines contain oxygenates and are spe- and driveability problems and may damage critical cifically blended to reduce vehicle emissions and im-...
Page 266: Mmt In Gasoline
264 STARTING AND OPERATING If a Non-FFV vehicle is inadvertently fueled with E-85 MMT In Gasoline fuel, the engine will have some or all of these symptoms: MMT is a manganese-containing metallic additive that is • operate in a lean mode blended into some gasoline to increase octane.
Page 267: Materials Added To Fuel
STARTING AND OPERATING 265 Materials Added To Fuel CAUTION! (Continued) All gasoline sold in the United States is required to contain • An out-of-tune engine or certain fuel or ignition effective detergent additives. Use of additional detergents malfunctions can cause the catalytic converter to or other additives is not needed under normal conditions overheat.
Page 268: Carbon Monoxide Warnings
266 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper main- WARNING! tenance. Have the exhaust system inspected every Carbon monoxide (CO) in exhaust gases is deadly. time the vehicle is raised. Have any abnormal Follow the precautions below to prevent carbon conditions repaired promptly.
Page 269 STARTING AND OPERATING 267 CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impu- rities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “Malfunction Indi- cator Light (MIL)”...
Page 270: Loose Fuel Filler Cap Message
268 STARTING AND OPERATING Loose Fuel Filler Cap Message WARNING! (Continued) After fuel has been added, the vehicle diagnostic system • Never add fuel when the engine is running. It may can determine if the fuel filler cap is possibly loose, cause the MIL to turn on and could cause a fire.
Page 271: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 269 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF the Ground Manual Transmission Flat Tow NONE Transmission in NEUTRAL Dolly Tow Front Rear NOT ALLOWED On Trailer NOTE: Vehicles equipped with manual transmissions CAUTION! may be recreationally towed (flat towed) at any legal highway speed, for any distance, if the manual transmis-...
Page 273: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS HAZARD WARNING FLASHERS ...272 Preparations For Jacking ....284 IF YOUR ENGINE OVERHEATS ... .272 Jacking Instructions .
Page 274: Hazard Warning Flashers
272 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel below the radio. potential for overheating by taking the appropriate action. •...
Page 275: Tirefit Kit - If Equipped
WHAT TO DO IN EMERGENCIES 273 CAUTION! WARNING! Driving with a hot cooling system could damage your You or others can be badly burned by hot engine vehicle. If the pointer rises to the H (red) mark, the coolant (antifreeze) or steam from your radiator. If instrument cluster will sound a chime.
Page 276: Tirefit Storage
274 WHAT TO DO IN EMERGENCIES TIREFIT Storage TIREFIT Kit Components And Operation The TIREFIT kit is located under the front driver’s seat. TIREFIT Components TIREFIT Kit Location 1. Sealant Bottle 2. Deflation Button 3. Pressure Gauge...
Page 277: Tirefit Usage Precautions
WHAT TO DO IN EMERGENCIES 275 • When the TIREFIT sealant is in a liquid form, clean water, 4. Power Button and a damp cloth will remove the material from the 5. Mode Select Knob vehicle or tire and wheel components. Once the sealant 6.
Page 278 276 WHAT TO DO IN EMERGENCIES WARNING! WARNING! (Continued) • Keep TIREFIT away from open flames or heat • Do not attempt to seal a tire on the side of the source. vehicle closest to traffic. Pull far enough off the •...
Page 279: Sealing A Tire With Tirefit
WHAT TO DO IN EMERGENCIES 277 2. Verify that the valve stem (on the wheel with the WARNING! (Continued) deflated tire) is in a position that is near to the ground. • TIREFIT Sealant solution contains latex. In case of This will allow the TIREFIT Hoses (6) and (7) to reach an allergic reaction or rash, consult a physician the valve stem and keep the TIREFIT kit flat on the...
Page 280 278 WHAT TO DO IN EMERGENCIES (B) Setting Up To Use TIREFIT: (C) Injecting TIREFIT Sealant Into The Deflated Tire: 1. Turn the Mode Select Knob (5) to the Sealant Mode • Always start the engine before turning ON the TIRE- position.
Page 281 WHAT TO DO IN EMERGENCIES 279 If the sealant (white fluid) does not flow within 0 – If the sealant (white fluid) does flow through the 10 seconds through the Sealant Hose (6): Sealant Hose (6): 1. Press the Power Button (4) to turn Off the TIREFIT kit. 1.
Page 282 280 WHAT TO DO IN EMERGENCIES If the tire does not inflate to at least 26 psi (1.8 Bar) 3. Immediately disconnect the Sealant Hose (6) from the pressure within 15 minutes: valve stem, reinstall the cap on the fitting at the end of the hose, and place the TIREFIT kit in the vehicle •...
Page 283 WHAT TO DO IN EMERGENCIES 281 (D) Drive Vehicle: (E) After Driving: Immediately after injecting sealant and inflating the tire, Pull over to a safe location. Refer to “Whenever You Stop drive the vehicle 5 miles (8 km) or 10 minutes to ensure to Use TIREFIT”...
Page 284 282 WHAT TO DO IN EMERGENCIES If the tire pressure is 19 psi (1.3 bar) or higher: 5. Replace the Sealant Bottle (1) and Sealant Hose (6) assembly at your authorized studio as soon as possible. 1. Press the Power Button (4) to turn on TIREFIT and Refer to “(F) Sealant Bottle and Hose Replacement.”...
Page 285: Jacking And Tire Changing - If Equipped
WHAT TO DO IN EMERGENCIES 283 5. Position the new Sealant Bottle (1) in the housing so JACKING AND TIRE CHANGING — IF EQUIPPED that the Sealant Hose (6) aligns with the hose slot in the front of the housing. Press the bottle into the WARNING! housing.
Page 286: Jack Location
284 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas.
Page 287 WHAT TO DO IN EMERGENCIES 285 Block both the front and rear of the WARNING! wheel diagonally opposite the jacking position. For example, if changing the Do not attempt to change a tire on the side of the right front tire, block the left rear vehicle close to moving traffic, pull far enough off wheel.
Page 288: Jacking Instructions
286 WHAT TO DO IN EMERGENCIES Jacking Instructions WARNING! (Continued) • Do not get under the vehicle when it is on a jack. If WARNING! you need to get under a raised vehicle, take it to a Carefully follow these tire changing warnings to help service center where it can be raised on a lift.
Page 289 WHAT TO DO IN EMERGENCIES 287 CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1. Remove the scissors jack and tool bag from under the driver’s seat.
Page 290 288 WHAT TO DO IN EMERGENCIES 3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed.
Page 291 WHAT TO DO IN EMERGENCIES 289 WARNING! WARNING! Raising the vehicle higher than necessary can make To avoid the risk of forcing the vehicle off the jack, the vehicle less stable. It could slip off the jack and do not fully tighten the wheel bolts until the vehicle hurt someone near it.
Page 292: Jump-Starting Procedure
290 WHAT TO DO IN EMERGENCIES 7. Lower the vehicle by turning the jack screw to the left. JUMP-STARTING PROCEDURE If your vehicle has a discharged battery, it can be jump- 8. Finish tightening the bolts. Push down on the wrench started using a set of jumper cables and a battery in while tightening the wheel bolts.
Page 293: Preparations For Jump-Start
WHAT TO DO IN EMERGENCIES 291 CAUTION! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur. Preparations For Jump-Start The battery in your vehicle is located on the left side of the engine compartment.
Page 294 292 WHAT TO DO IN EMERGENCIES 3. Remove the protective cover over the remote posi- WARNING! tive (+) battery post. To remove the cover, press the • Take care to avoid the radiator cooling fan when- locking tab and pull upward on the cover. ever the hood is raised.
Page 295: Jump-Starting Procedure
WHAT TO DO IN EMERGENCIES 293 Jump-Starting Procedure 3. Connect the negative end (-) of the jumper cable to the negative (-) post of the booster battery. WARNING! 4. Connect the opposite end of the negative (-) jumper cable to a good engine ground (exposed metal part of Failure to follow this procedure could result in per- the discharged vehicle’s engine) away from the battery sonal injury or property damage due to battery ex-...
Page 296: Freeing A Stuck Vehicle
294 WHAT TO DO IN EMERGENCIES 5. Start the engine in the vehicle that has the booster CAUTION! battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged Accessories that can be plugged into the vehicle battery.
Page 297 WHAT TO DO IN EMERGENCIES 295 CAUTION! CAUTION! • When “rocking” a stuck vehicle by shifting be- Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the en- tween 2nd gear and REVERSE, do not spin the gine to idle with the shift lever in NEUTRAL for at wheels faster than 15 mph (24 km/h), or drivetrain least one minute after every five rocking-motion...
Page 298: Towing A Disabled Vehicle
296 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE WARNING! This section describes procedures for towing a disabled Fast spinning tires can be dangerous. Forces gener- vehicle using a commercial wrecker service. ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires.
Page 299: Manual Transmission
WHAT TO DO IN EMERGENCIES 297 Proper towing or lifting equipment is required to prevent Manual Transmission damage to your vehicle. Use only tow bars and other • Vehicle can be flat towed (all four wheels on the equipment designed for this purpose, following equip- ground) with the transmission in NEUTRAL.
Page 301 MAINTAINING YOUR VEHICLE CONTENTS ENGINE COMPARTMENT — 1.4L TURBO ..301 Maintenance-Free Battery ....309 ONBOARD DIAGNOSTIC SYSTEM — OBD II . .302 Air Conditioner Maintenance ... . .310 EMISSIONS INSPECTION AND MAINTENANCE Body Lubrication .
Page 302 300 MAINTAINING YOUR VEHICLE Appearance Care And Protection From Front Fog Lamps ..... .341 Corrosion ......327 Front/Rear Side Marker Lamps.
Page 303: Engine Compartment - 1.4L Turbo
MAINTAINING YOUR VEHICLE 301 ENGINE COMPARTMENT — 1.4L TURBO 1 — Engine Coolant Reservoir 5 — Battery 2 — Engine Oil Dipstick 6 — Engine Oil Fill 3 — Brake Fluid Reservoir 7 — Washer Fluid Reservoir 4 — Front Distribution Unit (Fuses)
Page 304: Onboard Diagnostic System - Obd Ii
302 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors further damage to the emission control system. It the performance of the emissions, engine, and automatic could also affect fuel economy and drivability.
Page 305 MAINTAINING YOUR VEHICLE 303 Indicator Light (MIL)” is functioning and is not on when 3. As soon as you turn the ignition switch to the ON the engine is running, and that the OBD II system is position, you will see the MIL symbol come on as part ready for testing.
Page 306: Replacement Parts
304 MAINTAINING YOUR VEHICLE you may need to do nothing more than drive your DEALER SERVICE vehicle as you normally would in order for your OBD II Your authorized dealer has the qualified service person- system to update. A recheck with the above test routine nel, special tools, and equipment to perform all service may then indicate that the system is now ready.
Page 307: Maintenance Procedures
MAINTAINING YOUR VEHICLE 305 WARNING! CAUTION! • Failure to properly maintain your vehicle or per- You can be badly injured working on or around a motor vehicle. Only do service work for which you form repairs and service when necessary could have the knowledge and the proper equipment.
Page 308: Engine Oil
306 MAINTAINING YOUR VEHICLE Engine Oil CAUTION! Checking Oil Level Do not overfill the engine with oil. Overfilling the To assure proper engine lubrication, the engine oil must engine with oil will cause oil aeration, which can be maintained at the correct level. Check the oil level at lead to loss of oil pressure and an increase in oil regular intervals, such as every fuel stop.
Page 309 MAINTAINING YOUR VEHICLE 307 Engine Oil Selection CAUTION! For best performance and maximum protection for tur- Do not use chemical flushes in your engine oil as the bocharged engines under all types of operating condi- chemicals can damage your engine. Such damage is tions, the manufacturer recommends synthetic engine not covered by the New Vehicle Limited Warranty.
Page 310: Engine Oil Filter
308 MAINTAINING YOUR VEHICLE Materials Added To Engine Oil Engine Oil Filter Selection Do not add any supplemental materials, other than leak This manufacturer’s engines have a full-flow type dispos- detection dyes, to the engine oil. Engine oil is an engi- able oil filter.
Page 311: Maintenance-Free Battery
MAINTAINING YOUR VEHICLE 309 WARNING! (Continued) WARNING! for repair or maintenance. Make sure that no one is • Battery fluid is a corrosive acid solution and can near the engine compartment before starting the burn or even blind you. Do not allow battery fluid vehicle with the air induction system (air cleaner, to contact your eyes, skin, or clothing.
Page 312: Air Conditioner Maintenance
310 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance WARNING! (Continued) For best possible performance, your air conditioner should • The battery in this vehicle has a vent hose that be checked and serviced by an authorized studio at the should not be disconnected and should only be start of each warm season.
Page 313 MAINTAINING YOUR VEHICLE 311 Refrigerant Recovery And Recycling WARNING! R-134a Air Conditioning Refrigerant is a hydrofluoro- • Use only refrigerants and compressor lubricants carbon (HFC) that is endorsed by the Environmental approved by the manufacturer for your air condi- Protection Agency and is an ozone-saving product. How- tioning system.
Page 314 312 MAINTAINING YOUR VEHICLE The A/C air filter is located in the fresh air inlet on the 2. Pull the console closeout cover rearward to disengage lower right of center console. Perform the following the front retaining tab and remove the cover. procedure to replace the filter: 1.
Page 315 MAINTAINING YOUR VEHICLE 313 3. Remove the two 5.5mm screws (1 and 2) that secure the particulate air filter cover to the HVAC housing. A/C Air Filter 5. Install the A/C air filter with the air filter position indicators pointing in the same direction as removal. 4.
Page 316: Body Lubrication
314 MAINTAINING YOUR VEHICLE application of any lubricant, the parts concerned should CAUTION! be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular The A/C air filter is identified with an arrow to attention should also be given to hood latching compo- indicate airflow direction through the filter.
Page 317 MAINTAINING YOUR VEHICLE 315 Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield.
Page 318: Adding Washer Fluid
316 MAINTAINING YOUR VEHICLE 3. Grab the bottom of the wiper blade and rotate it 4. Install the wiper blade pivot pin into the wiper blade forward to unsnap the blade pivot pin from the wiper holder at the end of the wiper arm, and firmly press blade holder.
Page 319: Exhaust System
MAINTAINING YOUR VEHICLE 317 into the passenger compartment. In addition, have the WARNING! exhaust system inspected each time the vehicle is raised for lubrication or oil change. Replace as required. Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care WARNING! must be exercised when filling or working around the washer solution.
Page 320 318 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- CAUTION! verter will not require maintenance. However, it is im- • The catalytic converter requires the use of un- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst leaded fuel only.
Page 321: Cooling System
MAINTAINING YOUR VEHICLE 319 To minimize the possibility of catalytic converter damage: WARNING! (Continued) • Do not shut off the engine or interrupt the ignition, controlled and can start at any time the ignition when the transmission is in gear and the vehicle is in switch is in the ON position.
Page 322 320 MAINTAINING YOUR VEHICLE accumulation of bugs, leaves, etc. If dirty, clean by gently CAUTION! spraying water from a garden hose vertically down the • Mixing of engine coolant (antifreeze) other than face of the condenser. specified Organic Additive Technology (OAT) en- Cooling System –...
Page 323 MAINTAINING YOUR VEHICLE 321 Please review these recommendations for using Organic CAUTION! (Continued) Additive Technology (OAT) engine coolant (antifreeze). • Do not use water alone or alcohol-based engine When adding engine coolant (antifreeze): coolant (antifreeze) products. Do not use additional •...
Page 324 322 MAINTAINING YOUR VEHICLE Please note that it is the owner’s responsibility to main- WARNING! tain the proper level of protection against freezing ac- • The warning words “DO NOT OPEN HOT” on the cording to the temperatures occurring in the area where the vehicle is operated.
Page 325 MAINTAINING YOUR VEHICLE 323 Disposal Of Used Engine Coolant As long as the engine operating temperature is satisfac- tory, the coolant bottle need only be checked once a Used ethylene glycol-based engine coolant (antifreeze) is month. a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal When additional engine coolant (antifreeze) is needed to rules for your community.
Page 326: Brake System
324 MAINTAINING YOUR VEHICLE • Make sure that the coolant expansion bottle overflow If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be hoses are not kinked or obstructed. safely driven. The vapor will soon dissipate. •...
Page 327 MAINTAINING YOUR VEHICLE 325 brake pads wear. The brake fluid level should be checked WARNING! when the pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Riding the brakes can lead to brake failure and possibly a collision.
Page 328 326 MAINTAINING YOUR VEHICLE WARNING! WARNING! (Continued) fluid in a open container absorbs moisture from the • Use only manufacturer’s recommended brake air resulting in a lower boiling point. This may fluid. Refer to “Fluids, Lubricants, and Genuine cause it to boil unexpectedly during hard or pro- Parts”...
Page 329: Manual Transmission
MAINTAINING YOUR VEHICLE 327 Frequency Of Fluid Change CAUTION! Under normal operating conditions, the fluid installed at Use of improper brake fluids will affect overall clutch the factory will give satisfactory lubrication for the life of system performance. Improper brake fluids may dam- the vehicle.
Page 330 328 MAINTAINING YOUR VEHICLE hot or cold weather and other extreme conditions will Washing have an adverse effect on paint, metal trim, and under- • Wash your vehicle regularly. Always wash your ve- body protection. hicle in the shade using MOPAR Car Wash, or a mild car wash soap, and rinse the panels completely with The following maintenance recommendations will enable clear water.
Page 331 MAINTAINING YOUR VEHICLE 329 • If you detect any stone chips or scratches in the paint, CAUTION! touch them up immediately. The cost of such repairs is • Do not use abrasive or strong cleaning materials considered the responsibility of the owner. such as steel wool or scouring powder that will •...
Page 332: Maintaining Your Vehicle
330 MAINTAINING YOUR VEHICLE Wheel And Wheel Trim Care Stain Repel Fabric Cleaning Procedure – If Equipped • All wheels and wheel trim, especially aluminum and Stain Repel seats may be cleaned in the following manner: chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion.
Page 333 MAINTAINING YOUR VEHICLE 331 Interior Care WARNING! Use MOPAR Total Clean to clean fabric upholstery and Do not use volatile solvents for cleaning purposes. carpeting. Many are potentially flammable, and if used in Use MOPAR Total Clean to clean vinyl upholstery. closed areas they may cause respiratory harm.
Page 334 332 MAINTAINING YOUR VEHICLE Glass Surfaces Instrument Panel Bezels All glass surfaces should be cleaned on a regular basis CAUTION! with MOPAR Glass Cleaner, or any commercial household-type glass cleaner. Never use an abrasive type When installing hanging air fresheners in your ve- cleaner.
Page 335: Fuses
MAINTAINING YOUR VEHICLE 333 Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water.
Page 336 334 MAINTAINING YOUR VEHICLE Vehicle Vehicle Mini Mini Cavity Fuse Description Cavity Fuse Description Fuse Fuse Number Number Right Low Beam 20 Amp Bi-Directional Yellow Washer Brown 20 Amp Passenger Power 5 Amp Front and Rear Yellow Window Ceiling Lights Left Low Beam, Trunk and Door Headlamp Leveling...
Page 337: Underhood Fuses
MAINTAINING YOUR VEHICLE 335 Underhood Fuses Vehicle Mini Cavity Fuse Description The Front Distribution Unit is located on the right side of Fuse Number the engine compartment, next to the battery. To access the fuses, press the release tabs and remove the cover. 5 Amp Stop Light Switch, Instrument Panel...
Page 338 336 MAINTAINING YOUR VEHICLE The ID number of the electrical component correspond- Maxi Cavity Mini Fuse Description ing to each fuse can be found on the back of the cover. Fuse 30 Amp Radiator Fan - Maxi Cavity Mini Fuse Description Green Low Speed...
Page 339 MAINTAINING YOUR VEHICLE 337 Maxi Maxi Cavity Mini Fuse Description Cavity Mini Fuse Description Fuse Fuse 5 Amp High beam 7.5 Amp Air Conditioning (Shutter) Brown 15 Amp Cigar Lighter 15 Amp Heated Seats – If Blue Blue Equipped 7.5 Amp Transmission 15 Amp Fuel Pump...
Page 340: Vehicle Storage
338 MAINTAINING YOUR VEHICLE VEHICLE STORAGE Maxi Cavity Mini Fuse Description Fuse If you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your 10 Amp Transmission battery. • Disconnect the negative cable from the battery. 15 Amp Rear Defroster, Blue...
Page 341: Replacement Bulbs
MAINTAINING YOUR VEHICLE 339 REPLACEMENT BULBS Bulb Number Side Direction Lamps Interior Bulbs Rear Turn Signal Lamps PY21W Bulb Number Rear Side Marker Lamps Overhead Lamp Rear Tail and Stop PY21W/5W Courtesy Lamp Lamps Rear Backup Lamps W16W Exterior Bulbs Center High Mounted Bulb Number Stop Lamp...
Page 342: Bulb Replacement
340 MAINTAINING YOUR VEHICLE BULB REPLACEMENT Headlamps 1. Remove the plastic cap from the back of the headlamp housing. 2. Rotate the bulb counter-clockwise. 3. Remove the bulb and replace as needed. 4. Install the bulb and rotate clockwise to lock in place. 5.
Page 343: Front Fog Lamps
MAINTAINING YOUR VEHICLE 341 6. Install the bulb into socket, and rotate bulb/socket Rear Tail, Stop, Backup And Turn Signal Lamps clockwise into lamp locking it in place. 1. Open the liftgate. 7. Reinstall the plastic cap. 2. Remove the two screws and remove the tail lamp Front Fog Lamps assembly.
Page 344: Center High Mounted Stop Lamp (Chmsl)
342 MAINTAINING YOUR VEHICLE 4. Remove the tail, stop, or turn signal bulbs by pushing 3. Disconnect the electric connector. them slightly and turning counter-clockwise. 4. Press the retaining device and open the bulb holder. 5. Remove the backup lamp bulb by pulling straight out. 5.
Page 345: Fluid Capacities
MAINTAINING YOUR VEHICLE 343 FLUID CAPACITIES U.S. Metric Fuel (Approximate) 10.5 Gallons 40 Liters Engine Oil with Filter 1.4 Liter Turbo Engine 4 Quarts 3.8 Liters Cooling System 1.4 Liter Turbo Engine (MOPAR Antifreeze/Engine Coolant 4.6 Quarts 4.4 Liters 10 Year/150,000 Mile Formula or equivalent)
Page 346: Fluids, Lubricants And Genuine Parts
344 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of Chrysler Material Standard MS-12106. Engine Oil Use API Certified SAE 5W-40 Full Synthetic Engine Oil, meeting the requirements of Chrysler Material Standard MS-10896.
Page 347: Chassis
MAINTAINING YOUR VEHICLE 345 Chassis Component Fluid, Lubricant, or Genuine Part Manual Transmission MOPAR C635 DDCT/MTX Transmission Fluid Brake Master Cylinder MOPAR DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids or equivalent.
Page 349: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS MAINTENANCE SCHEDULE ... . .348 Maintenance Chart.....350...
Page 350 348 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE Once A Month Or Before A Long Trip: • Check engine oil level Your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will • Check windshield washer fluid level remind you that it is time to take your vehicle in for •...
Page 351 MAINTENANCE SCHEDULES 349 Required Maintenance Intervals. At Every Oil Change Interval As Indicated By Oil Change Indicator System: Refer to the Maintenance Schedules on the following • Inspect brake pads, shoes, rotors, drums, hoses pages for required maintenance. and park brake. At Every Oil Change Interval As Indicated By Oil •...
Page 352 350 MAINTENANCE SCHEDULES Maintenance Chart Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, boot seals, and replace if necessary. Inspect the brake linings, parking brake function. Additional Maintenance Replace cabin/air conditioning filter.
Page 353 MAINTENANCE SCHEDULES 351 Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Clean and lube sun roof tracks. Replace engine air filter. Replace the spark plugs. ** Flush and replace the engine cool- ant at 10 years or 150,000 miles (240,000 km) whichever comes first.
Page 354 352 MAINTENANCE SCHEDULES WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 355: If You Need Consumer Assistance
DEPARTMENT OF TRANSPORTATION UNIFORM FIAT Customer Center ....355 TIRE QUALITY GRADES ....359 Customer Assistance For The Hearing Or Speech Treadwear.
Page 356: Suggestions For Obtaining Service For Your Vehicle
354 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 357: Fiat Customer Center
• Vehicle delivery date and mileage This is why you should always talk to an authorized FIAT Customer Center studio service manager first. Most matters can be re- solved with this process. P.O. Box 21–8004 •...
Page 358: Service Contract
356 IF YOU NEED CONSUMER ASSISTANCE Canadian residents with hearing difficulties that require The manufacturer will not stand behind any service assistance can use the special needs relay service offered contract that is not the manufacturer’s service contract. It by Bell Canada. For TTY teletypewriter users, dial 711 is not responsible for any service contract other than the and for Voice callers, dial 1 800 855-0511 to connect with manufacturer’s service contract.
Page 359: Warranty Information
See the Warranty Information Booklet, located on the To contact NHTSA, you may either call the Auto Safety DVD, for the terms and provisions of FIAT Group Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), Automobiles warranties applicable to this vehicle and or go to http://www.safercar.gov;...
Page 360: In Canada
Canadian customers who wish to report a safety diagnosing/troubleshooting, problem solving, maintain- defect to the Canadian government should contact Trans- ing, servicing, and repairing FIAT Group Automobiles port Canada, Motor Vehicle Defect Investigations and vehicles. A complete working knowledge of the vehicle, Recalls at 1-800-333-0510 or go to http://www.tc.gc.ca/...
Page 361: Department Of Transportation Uniform
The following tire grading categories were established by assistance of service and engineering specialists to ac- the National Highway Traffic Safety Administration. The quaint you with specific FIAT Group Automobiles ve- specific grade rating assigned by the tire’s manufacturer hicles. Included are starting, operating, emergency and...
Page 362: Traction Grades
360 IF YOU NEED CONSUMER ASSISTANCE significantly from the norm due to variations in driving Temperature Grades habits, service practices, and differences in road charac- The temperature grades are A (the highest), B, and C, teristics and climate. representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under Traction Grades controlled conditions on a specified indoor laboratory...
Page 363 IF YOU NEED CONSUMER ASSISTANCE 361 WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive load- ing, either separately or in combination, can cause heat buildup and possible tire failure.
Page 365 INDEX...
Page 366 364 INDEX Adding Engine Coolant (Antifreeze) ... .321 Antifreeze (Engine Coolant) ....320 Adding Fuel ......266 Capacities .
Page 367 INDEX 365 Brake, Parking ......225 Cellular Phone ......197 Brakes .
Page 368 366 INDEX Coolant (Antifreeze) ..... . .343 Diagnostic System, Onboard ....302 Cooling System.
Page 369 INDEX 367 Jacking ......283 Temperature Gauge .....149 Jump Starting .
Page 370 368 INDEX Fluid Leaks ......79 Fueling ....... .266 Fluids, Lubricants and Genuine Parts .
Page 371 INDEX 369 Headlights ......106 Instrument Panel Cover .....332 Cleaning .
Page 372 370 INDEX Latches ....... . .79 Malfunction Indicator (Check Engine) ..146 Hood .
Page 373 INDEX 371 Lubrication, Body ......314 Multi-Function Control Lever ....106 Maintenance Free Battery.
Page 374 372 INDEX Recommendation ..... . .307 Windows ......21 Viscosity .
Page 375 INDEX 373 Remote Sound System (Radio) Controls ..195 And Pregnant Women ....37 Replacement Bulbs ......339 Child Restraint .
Page 376 374 INDEX Shoulder Belts ......27 Storage ....... .338 Side Airbag .
Page 377 INDEX 375 General Information .....246 Towing ....... .268 High Speed .
Page 378 376 INDEX Unleaded Gasoline ......262 Washing Vehicle ......328 Untwisting Procedure, Seat Belt .
Page 379 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Page 380 Chrysler Group LLC Printed in U.S.A. 3rd Edition 13FX24-126-AC...

This manual is also suitable for:

2013 500 abarth

Fiat 500 Abarth Owner's Manual

Introduction

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

If You Need Consumer Assistance

Quick Links

Chapters

Related Manuals for Fiat 500 Abarth

Summary of Contents for Fiat 500 Abarth