Page 1 FIAT 500 2 0 1 3 O W N E R ’ S M A N U A L...
Page 2 WARNING! FIAT is a registered trademark of Fiat Group Marketing & Corporate Communication S.p.A., used under license by Driving after drinking can lead to an accident. Your Chrysler Group LLC.
Page 3: Introduction 3
TABLE OF CONTENTS SECTION PAGE INTRODUCTION ............. 3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE .
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 VEHICLE IDENTIFICATION NUMBER ..7 HOW TO USE THIS MANUAL ....5 VEHICLE MODIFICATIONS/ALTERATIONS .
Page 6: Introduction
- all essentials that are maintaining its validity traditional to our vehicles. • the range of additional services available to FIAT This Owner’s Manual has been prepared with the assis- Group Automobiles customers tance of service and engineering specialists to acquaint NOTE: After reviewing the owner information, it you with the operation and maintenance of your vehicle.
Page 7: How To Use This Manual
INTRODUCTION 5 HOW TO USE THIS MANUAL The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects. Consult the Table of Contents to determine which section contains the information you desire. Consult the following table for a description of the symbols that may be used on your vehicle or throughout Since the specification of your vehicle depends on the this Owner’s Manual:...
Page 8 6 INTRODUCTION...
Page 9: Vehicle Identification Number
INTRODUCTION 7 WARNINGS AND CAUTIONS This Owners Manual contains WARNINGS against op- erating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information.
Page 10: Vehicle Modifications/Alterations
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN.
Page 11: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A WORD ABOUT YOUR KEYS ....11 Remote Key Unlock, Driver Door/All Doors 1st Press .......16 Ignition Key Removal .
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS ....25 Advanced Front Air Bag Features ...41 Lap/Shoulder Belts .
Page 13: Things To Know Before Starting Your Vehicle 9
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 A WORD ABOUT YOUR KEYS The vehicle is supplied with a code card containing key code numbers to order duplicate keys, and the autho- The key fob contains the Remote Keyless Entry (RKE) rized studio that sold you your new vehicle has the key transmitter with an integrated key.
Page 14 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, and push ignition button to place ignition in OFF position. When leaving the vehicle, always lock your ve- hicle.
Page 15: Locking Doors With A Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key-In-Ignition Reminder WARNING! (Continued) Opening the driver’s door when the key is in the ignition • Do not leave children or animals inside parked and the ignition switch position is OFF/LOCK, sounds a vehicles in hot weather.
Page 16: Replacement Keys
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A key which has not been programmed is also Replacement Keys considered an invalid key, even if it is cut to fit the NOTE: Only keys that have been programmed to the ignition switch lock cylinder for that vehicle.
Page 17: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 General Information REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED The Sentry Key® system complies with FCC rules part 15 This system allows you to lock or unlock the doors and and with RSS-210 of Industry Canada. Operation is liftgate from distances up to approximately 66 ft (20 m) subject to the following conditions: using a hand-held Remote Keyless Entry (RKE) transmit-...
Page 18: To Unlock The Doors And Liftgate
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The line of transmission must not be blocked To Lock The Doors And Liftgate with metal objects. Press and release the LOCK button on the RKE transmit- ter to lock all doors and the liftgate. The turn signal lights To Unlock The Doors And Liftgate will flash and the horn will chirp to acknowledge the Press and release the UNLOCK button on the RKE...
Page 19: Transmitter Battery Replacement
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 2. This device must accept any interference that may be The recommended replacement battery is CR2032. received including interference that may cause unde- 1. Press the mechanical key release button and release sired operation.
Page 20 18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Rotate the screw located on the side of the Key Fob 3. Take out the battery case. Remove and replace the using a small screwdriver. battery observing its polarity. Key Fob Screw Location Battery Case Removed...
Page 21: Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 4. Refit the battery case inside the Key Fob and turn the screw to lock it into place. DOOR LOCKS The door locks can be manually locked or unlocked from inside the vehicle by using the door handle. If the door handle is pushed a red lock indicator will show on the door handle (indicating locked) when the door is closed, the door will lock.
Page 22 20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • For personal security and safety in the event of an • Do not leave the Key Fob in or near the vehicle, or collision, lock the vehicle doors as you drive as in a location accessible to children, and do not well as when you park and leave the vehicle.
Page 23: Power Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Power Door Locks A power door lock switch is incorporated into the door handle. Push or pull the handle to lock or unlock the doors and liftgate. If the door handle is pushed a red lock indicator will show on the door handle (indicating locked) when the door is closed, the door will lock.
Page 24: Power Windows
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Autoclose — If Equipped POWER WINDOWS When enabled, the door locks will lock automatically Power Window Switches when the vehicle’s speed exceeds 15 mph (24 km/h). There are single window controls located on the shifter To change the setting proceed as follows: bezel, below the climate controls, which operate the driver and passenger door windows.
Page 25: Liftgate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 down automatically. To cancel the Auto-Down move- ment, operate the switch in either the up or down direction and release the switch. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.
Page 26 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To open the liftgate, squeeze the liftgate release handle WARNING! and pull the liftgate open with one fluid motion. • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes.
Page 27: Occupant Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 • All seat belt systems (except the driver’s) include OCCUPANT RESTRAINTS Automatic Locking Retractors (ALRs), which lock the Some of the most important safety features in your seat belt webbing into position by extending the belt vehicle are the restraint systems: all the way out and then adjusting the belt to the •...
Page 28 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can take to minimize the children to slide the shoulder belt behind them or under risk of harm from a deploying air bag: their arm. You should read the instructions provided with your 1.
Page 29 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 5. If the air bag system in this vehicle needs to be WARNING! (Continued) modified to accommodate a disabled person, contact • Being too close to the steering wheel or instrument the Customer Center. Phone numbers are provided in panel during Advanced Front Air Bag deployment If You Need Consumer Assistance.
Page 30: Lap/Shoulder Belts
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ejection and the risk of injury caused by striking the WARNING! inside of the vehicle. Everyone in a motor vehicle should be belted at all times. In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled Lap/Shoulder Belts up.
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WARNING! WARNING! (Continued) • Wearing your belt in the wrong place could make • It is dangerous to ride in a cargo area, inside or your injuries in a collision much worse. You might outside of a vehicle.
Page 32 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is along side the pillar near the 3. When the belt is long enough to fit, insert the latch back of your seat. Grasp the latch plate and pull out plate into the buckle until you hear a “click.”...
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! WARNING! (Continued) • A belt that is worn under your arm is dangerous. • A belt buckled into the wrong buckle will not Your body could strike the inside surfaces of the protect you properly.
Page 34 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your WARNING! abdomen. To remove slack in the lap belt portion, pull • A lap belt worn too high can increase the risk of up on the shoulder belt.
Page 35: Lap/Shoulder Belt Untwisting Procedure
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 6. To release the belt, push the red button on the buckle. 1. Position the latch plate as close as possible to the The belt will automatically retract to its stowed posi- anchor point.
Page 36: Automatic Locking Retractor Mode (Alr) - If Equipped
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Restraints” section. The chart below defines the type of out only the amount of webbing necessary to comfort- feature for each seating position. ably wrap around the occupant’s mid-section. Slide the latch plate into the buckle until you hear a click. Driver Passenger Automatic Locking Retractor Mode (ALR) —...
Page 37: Energy Management Feature
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 2. Grasp the shoulder portion and pull downward until WARNING! the entire belt is extracted. • The belt and retractor assembly must be replaced if 3. Allow the belt to retract. As the belt retracts, you will the seat belt assembly Automatic Locking Retractor hear a clicking sound.
Page 38: Seat Belt Pretensioners
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners Enhanced Seat Belt Use Reminder System (BeltAlert®) The seat belts for both front seating positions are equipped with pretensioning devices that are designed to BeltAlert® is a feature intended to remind the driver and remove slack from the seat belt in the event of a collision.
Page 39: Seat Belt Extender
WARNING! BeltAlert® can be enabled or disabled by your autho- Using a seat belt extender when not needed can rized studio. FIAT Group Automobiles does not recom- increase the risk of injury in a collision. Only use mend deactivating BeltAlert®.
Page 40: Seat Belts And Pregnant Women
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts And Pregnant Women Supplemental Restraint System (SRS) — Air Bags We recommend that pregnant women use the seat belts This vehicle has Advanced Front Air Bags for both the throughout their pregnancy. Keeping the mother safe is driver and front passenger as a supplement to the seat the best way to keep the baby safe.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 NOTE: The Driver and Passenger Advanced Front Air Bags are certified to new Federal regulations for Ad- vanced Air Bags. The Advanced Front Air Bags are designed to allow the air bags to have different inflation levels based on several factors, including the severity and type of collision.
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Air Bag Warning Light and rear passengers sitting next to a window. The SABIC are located above the side windows. The trim covering • Steering Wheel and Column the SABIC is labeled SRS AIRBAG. •...
Page 43: Advanced Front Air Bag Features
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Advanced Front Air Bag Features WARNING! (Continued) The Advanced Front Air Bag system provides output • Do not put anything on or around the air bag appropriate to the severity and type of collision as covers or attempt to open them manually.
Page 44 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Seat-Mounted Side Air Bags (SAB) When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag Supplemental Seat-Mounted Side Air Bags (SAB) provide deploys independently;...
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 The system includes side impact sensors that are cali- brated to deploy the Seat-Mounted Side Air Bags (SAB) and SABIC during impacts that require air bag occupant protection. SAB and SABIC air bags are a supplement to the seat belt restraint system.
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Your vehicle is equipped with SABIC air bags, do • Your vehicle is equipped with left and right not have any accessory items installed which will Supplemental Side Air Bag Inflatable Curtain alter the roof, including adding a sunroof to your (SABIC), do not stack luggage or other cargo up vehicle.
Page 47: Air Bag Deployment Sensors And Controls
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Supplemental Driver Side Knee Air Bag Air Bag Deployment Sensors And Controls The Supplemental Driver Side Knee Air Bag provides Occupant Restraint Controller (ORC) enhanced protection and works together with the Driver The ORC is part of a Federally regulated safety system Advanced Front Air Bag during a frontal impact.
Page 48 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE severity and type of collision. Advanced Front Air Bags Because air bag sensors measure vehicle deceleration are not expected to reduce the risk of injury in rear or side over time, vehicle speed and damage by themselves are collisions.
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 The ORC contains a backup power supply system that WARNING! may deploy the air bags even if the battery loses power or it becomes disconnected prior to deployment. Ignoring the Air Bag Warning Light in your instru- ment panel could mean you won’t have the air bags Also, the ORC turns on the Air Bag Warning to protect you in a collision.
Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE are possible, based on several factors, including the Supplemental Driver Side Knee Air Bag. The trim cover collision type and severity. The steering wheel hub trim separates and folds out of the way allowing the air bag to cover and the upper right side of the instrument panel inflate to the full size.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 between the occupant and the door. The SAB fully inflate covers the window. The air bag inflates in about 30 in about 10 milliseconds. The side air bag moves at a very milliseconds (about one-quarter of the time that it takes high speed and with such a high force that it could injure to blink your eyes) with enough force to injure you if you...
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Accident Response System After the event occurs, when the system is active, the message Fuel Cutoff See Handbook is displayed. In the event of an impact causing air bag deployment, if the communication network remains intact, and the Carefully check the vehicle for fuel leaks in the engine power remains intact, depending on the nature of the...
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Customer Action Customer Will See 1. Turn ignition OFF. (Turn Signal Switch Must be placed in Neutral State). 2. Turn ignition ON. Left Turn Light is OFF. Right Turn Light BLINKS. 3. Turn Right Turn Signal Switch ON. Right Turn Light is ON SOLID.
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If a reset procedure step is not completed within 45 floor. They are not caused by contact with chemicals. seconds, then the turn signal lights will turn off and the They are not permanent and normally heal quickly. reset procedure must be performed again in order to be However, if you haven’t healed significantly within a successful.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Maintaining Your Air Bag System WARNING! WARNING! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, • Modifications to any part of the air bag system seat belt pretensioners, and the front seat belt retrac- could cause it to fail when you need it.
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Warning Light WARNING! (Continued) • Do not attempt to modify any part of your air bag You will want to have the air bags ready to system. The air bag may inflate accidentally or may inflate for your protection in a collision.
Page 57: Event Data Recorder (Edr)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 • How various systems in your vehicle were operating; NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint • Whether or not the driver and passenger safety belts Controller (ORC) may also be disabled.
Page 58: Child Restraints
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To read data recorded by an EDR, special equipment is There are different sizes and types of restraints for required, and access to the vehicle or the EDR is needed. children from newborn size to the child almost large In addition to the vehicle manufacturer, other parties, enough for an adult safety belt.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 WARNING! In a collision, an unrestrained child can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommended Type of Child Size, Height, Weight or Age Child Restraint Small Children Children who are at least two Forward-Facing Child Restraint years old or who have out-grown with a five-point Harness, facing the height or weight limit of their forward in the rear seat of the rear-facing child restraint...
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Infants And Child Restraints reach the highest weight or height allowed by their convertible child seat. Safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until WARNING! they reach either the height or weight limit of their rear facing child safety seat.
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE have outgrown the rear-facing weight or height limit of WARNING! their rear-facing convertible child seat. Children should • Improper installation can lead to failure of an remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height infant or child restraint.
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Children Too Large For Booster Seats 4. Is the lap part of the belt as low as possible, touching the child’s thighs and not their stomach? Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend 5.
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints Restraint Type Combined Use any attachment method shown with an “X” Below Weight of the LATCH – LATCH – Child + Child Lower Anchors Seat Belt + Top Lower Anchors Seat Belt Only Restraint...
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Lower Anchors and Tethers for Children (LATCH) Anchors and Tethers for CHildren. The LATCH system Restraint System has three vehicle anchor points for installing LATCH- equipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH Positions For Installing Child Restraints In This Vehicle • Lower Anchorage Symbol 2 anchorages per seat- ing position • Top Tether Anchorage Symbol...
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 What is the weight limit (child’s weight + 65 lbs (29.5 kg) Use the LATCH anchorage system until weight of the child restraint) for using the the combined weight of the child and the LATCH anchorage system to attach the child child restraint is 65 lbs (29.5 kg).
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Can two child restraints be attached using Never “share” a LATCH anchorage with a common lower LATCH anchorage? two or more child restraints. If the center position does not have dedicated LATCH lower anchorages, use the seat belt to in- stall a child seat in the center position next to a child seat using the LATCH anchor-...
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint.
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH-compatible child restraint systems will be To Install A LATCH-compatible Child Restraint equipped with a rigid bar or a flexible strap on each side. 1. If the selected seating position has a Switchable Auto- Each will have a hook or connector to attach to the lower matic Locking Retractor (ALR) seat belt, stow the seat anchorage and a way to tighten the connection to the...
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 4. Attach the lower hooks or connectors of the child How To Stow An Unused ALR Seatbelt restraint to the lower anchorages in the selected seat- When using the LATCH attaching system to install a ing position.
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the seat belt tight around the child restraint so that it is WARNING! not necessary to use a locking clip. The ALR retractor can be “switched” into a locked mode by pulling all of the Improper installation of a child restraint to the webbing out of the retractor and then letting the webbing LATCH anchorages can lead to failure of the re-...
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle What is the weight limit (child’s weight + Weight limit of the Always use the tether anchor when using weight of the child restraint) for using the Child Restraint the seat belt to install a forward facing child Tether Anchor with the seat belt to attach a...
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Can the rear-facing child restraint touch the Contact between the front passenger seat back of the front passenger seat? and the child restraint is allowed, if the child restraint manufacturer also allows contact. Can the head restraints be removed? Yes, all.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 5. To lock the seat belt, pull down on the shoulder part of 8. If the child restraint has a top tether strap and the the belt until you have pulled all the seat belt webbing seating position has a top tether anchorage, connect out of the retractor.
Page 76 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing A Child Restraint With A Cinching 5. If the child restraint has a top tether strap and the Latch Plate (CINCH) — If Equipped seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether 1.
Page 77 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 facing out, away from the child restraint. Repeat steps 4 2. Route the tether strap to provide the most direct path to 6, above, to complete the installation of the child for the strap between the anchor and the child seat. If restraint.
Page 78: Transporting Pets
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap.
Page 79: Engine Break-In Recommendations
(transmission and axle) in your vehicle. in the engine or damage may result. Drive moderately during the first 300 miles (500 km). NOTE: A new engine may consume some oil during its After the initial 60 miles (100 km), speeds up to 50 or first few thousand miles (kilometers) of operation.
Page 80: Safety Tips
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS Exhaust Gas Transporting Passengers WARNING! NEVER TRANSPORT PASSENGERS IN THE CARGO Exhaust gases can injure or kill. They contain carbon AREA. monoxide (CO), which is colorless and odorless. WARNING! Breathing it can make you unconscious and can eventually poison you.
Page 81: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Safety Checks You Should Make Inside The WARNING! (Continued) Vehicle • If it is necessary to sit in a parked vehicle with the Seat Belts engine running, adjust your heating or cooling controls to force outside air into the vehicle.
Page 82 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE studio. If the light stays on, flickers, or comes on while WARNING! driving, have the system checked by an authorized studio. Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- Defroster sonal injury.
Page 83: Periodic Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Periodic Safety Checks You Should Make Outside WARNING! (Continued) The Vehicle • Check mounting of mats on a regular basis. Always Tires properly reinstall and secure floor mats that have been removed for cleaning. Examine tires for excessive tread wear and uneven wear •...
Page 84 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately.
Page 85: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS POWER CONVERTIBLE TOP — IF EQUIPPED . .86 Heated Mirrors — If Equipped ... .92 Lowering The Power Top....87 Sun Visors .
Page 86 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EZ Entry Feature ..... .104 Lane Change Assist ....112 Memory Feature .
Page 87 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 To Vary The Speed Setting ....121 Wind Buffeting ..... . .129 To Accelerate For Passing .
Page 88: Power Convertible Top - If Equipped
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER CONVERTIBLE TOP — IF EQUIPPED On vehicles equipped with a power convertible top, the power convertible top switch is located on the overhead console. The switch contains two buttons. The passenger side button, which is used to open the power top, and the driver side button, which is used to close the power top.
Page 89: Lowering The Power Top
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Lowering The Power Top CAUTION! Press the top open button approximately one second for Failure to follow these cautions may cause interior the partially open position. Press the top open button for water damage, stains or mildew on the top material: approximately one second a second time to fully open the •...
Page 90: Power Convertible Top Relearn Procedure
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Hold the OPEN button to move the top to the fully WARNING! open position. The convertible top does not provide the structural 4. CONTINUE to hold the OPEN button for an addi- protection that a reinforced metal roof does and the tional three seconds.
Page 91: Wind Stop
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Auto Open/Close will now be functional. Trunk lid Headlight glare from vehicles behind you can be reduced operation will be functional. by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror NOTE: DO NOT interrupt this activity.
Page 92: Automatic Dimming Mirror - If Equipped
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated.
Page 93: Power Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Power Mirrors mirror, press the mirror select switch to either the L (left) or R (right) to select the mirror you need to adjust. The power mirror controls are located on the driver’s door trim panel.
Page 94: Folding Mirrors
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Spotter Mirror — If Equipped Folding Mirrors Some models are equipped with a driver’s side spotter The exterior mirrors are hinged to allow the mirror to mirror. The spotter mirror allows for a greater range of pivot forward or rearward to help avoid damage.
Page 95: Blue&Me™ Hands-Free Communication - If Equipped
BLUE&ME™ HANDS-FREE COMMUNICATION — visors are equipped with courtesy mirrors. IF EQUIPPED Overview Windows Mobile™-based FIAT BLUE&ME™ is a per- sonal telematic system enabling you to use communica- tion and entertainment applications expressly designed for use in the car. The BLUE&ME™ system installed on your car is...
Page 96: The Hands-Free Kit
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE you are not required to train the voice recognition system The Hands-Free Kit to recognize your voice. This implies that the system is The basic characteristic of this hands-free kit is voice nearly equally performing with different persons, i.e.: the recognition with Bluetooth®...
Page 97 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 your mobile phone manually and visually using the To get started with BLUE&ME™ hands-free kit with steering wheel controls and the instrument panel multi- voice recognition, you have to simply pair your function display. Bluetooth®...
Page 98 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To interact with BLUE&ME™ you can use either the The hands-free kit enables the following operations: buttons on the steering wheel or voice commands. • Contact Calling By Voice — you can call a contact in With voice recognition, you can perform system func- your mobile phone phonebook using your voice.
Page 99 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 • Conference Call — you can call another contact while wheel. When using the hands-free phone, the audio you are engaged in a phone conversation (with output of a phone conversation is heard through your car Bluetooth®...
Page 100 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To delete individual messages or the entire inbox using Message reader functions are managed by the control buttons on the steering wheel or by the BLUE&ME™ the buttons on the steering wheel or voice commands. voice commands.
Page 101 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 • To use the media player, you have to simply connect The media player enables the following operations: (directly or by an extension lead) your USB device to • Digital Audio Playback — you can play all your the car USB port.
Page 102: Seats
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Keep the User’s Guide in the car: when kept in the • Operating certain parts of this system while driv- car, the User’s Guide will be a ready reference for ing can distract your attention away from the road, you and other users unfamiliar with the system.
Page 103: Front Seats Forward/Rearward Adjustment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Front Seats Forward/Rearward Adjustment WARNING! Your vehicle may be equipped with either an adjusting • It is dangerous to ride in a cargo area, inside or handle or adjusting bar that is located at the front of the outside of a vehicle.
Page 104: Recline Adjustment
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked.
Page 105: Seat Height Adjustment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Seat Height Adjustment The driver’s seat height can be raised or lowered by using a lever, located on the outboard side of the seat. Pump the lever upward to raise the seat height, or pump the lever downward to lower the seat height.
Page 106: Understanding The Features Of Your Vehicle Ez Entry Feature
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EZ Entry Feature Lift the seatback upright and push the seat rearward to its locked position once the rear passengers are seated. The driver and front passenger seats have an EZ entry feature for rear seat passengers. Pull forward on the Memory Feature release lever, located on the outboard side of the seatback, The driver seat also has a memory feature, which can...
Page 107: Heated Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 fore/aft (memory) position on the tracks. This results in WARNING! the seat back memory being set only – The track will then • Persons who are unable to feel pain to the skin be locked forward of its last set fore/aft memory posi- tion.
Page 108: Head Restraints
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints Reactive Head Restraints — Front Seats Head restraints are designed to reduce the risk of injury The front driver and passenger seats are equipped with by restricting head movement in the event of a rear- Reactive Head Restraints.
Page 109 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 NOTE: The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized studio. WARNING! Do not place items over the top of the Reactive Head Restraint, such as coats, seat covers or portable DVD players.
Page 110: To Open And Close The Hood
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Restraints” in “Things To Know Before Starting Your TO OPEN AND CLOSE THE HOOD Vehicle” for information on tether routing. To open the hood, two latches must be released. 1. Pull the bottom of the RED hood release lever, located on the left kick panel, rearward.
Page 111 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 2. Rotate the safety catch under the front edge of the In hot climates, the prop rod may be hot. Pick up the prop hood, near the center, and raise the hood. rod at the foam on the end of the prop rod. WARNING! Be sure the hood is fully latched before driving your vehicle.
Page 112: Lights
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Multifunction Lever The multifunction lever, located on the left side of the steering wheel, controls the operation of the headlights, headlight beam selection, passing light and turn signals. NOTE: The external lights can only be turned on with the ignition in the ON/RUN position.
Page 113: High Beams
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 High Beams Daytime Running Lights — If Equipped To activate the Daytime Running Lights (DRL), rotate the With the low beams activated, push the multi- end of the multifunction lever to the O symbol. function lever towards the instrument panel to NOTE: The low beams and side/taillights will not be on turn on the high beams.
Page 114: Turn Signals
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals NOTE: The indicators will automatically turn off when the turn has been completed and the steering wheel is Push the multifunction lever upward to signal a right returned to a straight position. turn or downward to signal a left turn.
Page 115: Interior Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Deactivation CAUTION! Pull the multifunction lever toward the steering wheel Before getting out of the vehicle be sure that the and hold it for more than two seconds. switch is in the center position or that the lights are Interior Lights off to avoid draining the battery.
Page 116: Front Fog Lights - If Equipped
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Light Timing (On/Right Position) • When all doors are closed a 15 minute timer is activated. NOTE: The timer is deactivated when the key is moved into the ON/RUN position. Front Fog Lights — If Equipped The fog light switch is located on the center stack of the instrument panel, just below the radio.
Page 117: Windshield Wipers And Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer lever is located on the right side of the steering column. NOTE: The windshield wipers/washers will only oper- ate with the ignition in the ON/RUN position. Front Windshield Wiper Operation There are five different modes of operation for the front windshield wipers.
Page 118 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Intermittent function only has one detent Front Windshield Washer Operation but wiper delay will vary with changes in vehicle speed. Pull the windshield wiper/washer lever toward the As vehicle speed increases the delay time will decrease. steering wheel to activate the washers.
Page 119: Rear Windshield Wiper
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 CAUTION! (Continued) • Always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper control is turned off and the blades cannot return to the off position, damage to the wiper motor may occur.
Page 120: Tilt Steering Column - If Equipped
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Windshield Washer Operation Push the windshield wiper/washer lever toward the instrument panel to activate the rear washer. Push and hold the lever for more than a half second and the wipers will activate automatically for three cycles after the lever is released.
Page 121: Electronic Speed Control
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
Page 122: To Activate
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Elec- WARNING! tronic Speed Control system has been designed to shut down if multiple Speed Control functions are operated at Leaving the Electronic Speed Control system on the same time.
Page 123: To Deactivate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 To Deactivate Pressing the RES (+) button once will result in a 1 mph (1.6 km/h) increase in set speed. Each subsequent tap of A soft tap on the brake pedal, pushing the CANC button, the button results in an increase of 1 mph (1.6 km/h).
Page 124: Rear Park Assist - If Equipped
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using Electronic Speed Control On Hills REAR PARK ASSIST — IF EQUIPPED The transmission may downshift on hills to maintain the The Rear Park Assist system provides an audible indica- vehicle set speed. tion of the distance between the rear fascia/bumper and a detected obstacle when backing up, e.g.
Page 125: Rear Park Assist Alerts
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 corners of the rear fascia/bumper, depending on the Rear Park Assist Alerts location, type and orientation of the obstacle. If an obstacle is behind the vehicle when REVERSE gear If several obstacles are detected, the Rear Park Assist is engaged, an audible alert is activated.
Page 126 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Audible And Visual Signals Supplied By The Rear Park Assist System SIGNAL MEANING INDICATION Obstacle Distance An obstacle is present within Audible signal (dashboard loudspeaker) • Sound pulses emitted at a rate that increases the sensors’...
Page 127: Failure Indications
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Failure Indications Cleaning The Rear Park Assist System A malfunction of the Rear Park Assist sensors or system Clean the Rear Park Assist sensors with water, car wash is indicated, during REVERSE gear engagement, by the soap and a soft cloth.
Page 128 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Clean the Rear Park Assist sensors regularly, taking CAUTION! care not to scratch or damage them. The sensors must • Rear Park Assist is only a parking aid and it is not be covered with ice, snow, slush, mud, dirt or debris.
Page 129 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 WARNING! WARNING! (Continued) • Before using ParkSense®, it is strongly recom- • Drivers must be careful when backing up even mended that the ball mount and hitch ball assem- when using ParkSense®. Always check carefully bly is disconnected from the vehicle when the behind your vehicle, look behind you, and be sure vehicle is not used for towing.
Page 130: Power Sunroof - If Equipped
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof roof switch is located in the overhead • Never leave children in a vehicle with the key in console. the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch.
Page 131: To Open
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 To Open Pinch Protect Feature Press and hold the power sunroof switch rearward for This feature will detect an obstruction in the opening of approximately one second and the sunroof will stop at the sunroof during Express Close operation.
Page 132: Emergency Operation
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Emergency Operation In case of electrical failure the sunroof can be operated with the hex wrench that is located in the glove box. There is a plug located in the rear of the sunroof opening at the center of the vehicle.
Page 133: Electrical Power Outlets
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 ELECTRICAL POWER OUTLETS Power is available when the ignition switch is in the ON/RUN or START position. Insert the cigar lighter or There is a standard 12 Volt (13 Amp) power outlet, accessory plug into the outlet for use. To preserve the located in the floor console, for added convenience.
Page 134 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. •...
Page 135: Cigar Lighter - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 CIGAR LIGHTER — IF EQUIPPED CAUTION! • Many accessories that can be plugged in draw WARNING! power from the vehicle’s battery, even when not in When the cigar lighter is in use it becomes very hot. use (i.e., cellular phones, etc.).
Page 136: Cupholders
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS For rear passengers, there are cupholders located on the floor between the front driver and passenger seats. For the driver and front passenger, cupholders are lo- cated on the floor console between the front seats. Rear Cupholders Front Cupholders...
Page 137: Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 STORAGE Passenger Seat Storage — If Equipped Some models may be equipped with storage under the Glove Box Compartment front passenger seat. Pull outward on the latch to open The glove box is located on the right side of the instru- the storage compartment.
Page 138: Cargo Area Features
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES The rear seatbacks have a fold down feature to allow increased cargo capacity. Push down the release button, located at the outboard top of the seatback and move the seatback to its folded- down position to provide a flat load floor cargo area.
Page 139: Rear Window Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 20 minutes. To manually shut the defroster off, push the button a second time.
Page 140 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window.
Page 141: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT PANEL FEATURES ..141 Change Engine Oil Indicator System ..160 INSTRUMENT CLUSTER — POP, LOUNGE, Trip Computer ..... . .161 500C .
Page 142 140 UNDERSTANDING YOUR INSTRUMENT PANEL Technical Specifications ....177 Radio Operation ..... .202 Quick Guide .
Page 143: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 141 INSTRUMENT PANEL FEATURES 1 — Side Vent 7 — Passenger Air Bag 13 — Storage Compartment 2 — Multifunction Lever – Light Control 8 — Glove Compartment 14 — Shift Lever 3 — Instrument Cluster And Warning Lights 9 —...
Page 144: Instrument Cluster - Pop, Lounge, 500C
142 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — POP, LOUNGE, 500C...
Page 145: Instrument Cluster - Sport
UNDERSTANDING YOUR INSTRUMENT PANEL 143 INSTRUMENT CLUSTER — SPORT...
Page 146: Instrument Cluster Descriptions
144 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 2. Rear Defrost Button 1. Glow Plug Light — If Equipped Press and release this button to turn on the rear window defroster. This indicator will illuminate This vehicle will inhibit engine cranking when the when the rear window defroster is on.
Page 147 UNDERSTANDING YOUR INSTRUMENT PANEL 145 5. High Beam Indicator CAUTION! (Continued) This light indicates that the headlights are on high • Do not use scrapers, sharp instruments, or abrasive beam. Pull the turn signal lever toward the steer- window cleaners on the interior surface of the ing wheel to switch the headlights to low beam.
Page 148 146 UNDERSTANDING YOUR INSTRUMENT PANEL 8. Generic Warning Light 10. Cruise On Indicator — If Equipped The Generic Warning Light will illuminate if This light will turn on when the electronic any of the following conditions occur: Oil speed control is ON. For further information, Change Request, Engine Oil Pressure Sensor refer to “Electronic Speed Control”...
Page 149 UNDERSTANDING YOUR INSTRUMENT PANEL 147 12. Charging System Light 14. Electronic Throttle Control (ETC) Light This light shows the status of the electrical charg- This light informs you of a problem with the ing system. The light should come on when the Electronic Throttle Control (ETC) system.
Page 150 148 UNDERSTANDING YOUR INSTRUMENT PANEL 15. Tire Pressure Monitoring Telltale Light reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Each tire, including the spare (if provided), Please note that the TPMS is not a substitute for proper should be checked monthly when cold and tire maintenance, and it is the driver’s responsibility to inflated to the inflation pressure recommended...
Page 151 UNDERSTANDING YOUR INSTRUMENT PANEL 149 alternate tires or wheels on the vehicle that prevent the 16. Automatic Gearbox Failure TPMS from functioning properly. Always check the This light will illuminate when there is an TPMS malfunction telltale after replacing one or more automatic transmission fault.
Page 152 150 UNDERSTANDING YOUR INSTRUMENT PANEL 18. Malfunction Indicator Light (MIL) CAUTION! The Malfunction Indicator Light (MIL) is part of Prolonged driving with the Malfunction Indicator an onboard diagnostic system, called OBDII, that Light (MIL) on could cause damage to the engine monitors engine and automatic transmission con- control system.
Page 153 UNDERSTANDING YOUR INSTRUMENT PANEL 151 19. Engine Temperature Warning Light 20. Brake Warning Light This light warns of an overheated engine condi- This light monitors various brake functions, tion. The engine coolant temperature indicator including brake fluid level and parking brake will illuminate and a single chime will sound after application.
Page 154 152 UNDERSTANDING YOUR INSTRUMENT PANEL Distribution (EBD). In the event of an EBD failure, the 21. Electronic Stability Control OFF (ESC OFF) Indica- Brake Warning Light will turn on along with the ABS tor Light Light. Immediate repair to the ABS system is required. This light indicates the Electronic Stability Con- Operation of the Brake Warning Light can be checked by trol system (ESC) has been turned off by the...
Page 155 Contact a Fiat studio if you still cannot start normally if the BRAKE warning light is not on. the engine.
Page 156 CAUTION! (Continued) means that the car is not protected by the engine inhibitor temperature gauge are lit, pull over and stop the device. Contact Fiat studio to have all the keys vehicle. Idle the vehicle with the air conditioner programmed.
Page 157 UNDERSTANDING YOUR INSTRUMENT PANEL 155 27. Odometer / Trip Odometer / Electronic Vehicle Infor- NOTE: If the vehicle is equipped with the Electronic mation Center (EVIC) Display Area Vehicle Information Center (EVIC) in the instrument cluster, all warnings including “door” and “gate” and This display indicates the total distance the vehicle has “Change Engine Oil”...
Page 158: Electronic Vehicle Information Center (Evic)
156 UNDERSTANDING YOUR INSTRUMENT PANEL 29. Tachometer The white area of the scale shows the permissible engine revolutions-per-minute (RPM x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 30. Speedometer The Speedometer shows the vehicle speed in miles per hour (mph) and/or kilometers per hour (km/h).
Page 159: Evic Displays
UNDERSTANDING YOUR INSTRUMENT PANEL 157 EVIC Displays 1 — Ice Warning Indicator 6 — Message Display 2 — Temperature Indicator 7 — Coolant Temperature Gauge 1 — Temperature Indicator 6 — Message Display 3 — Fuel Level Gauge 8 — Digital Speedometer 2 —...
Page 160: Evic Control Buttons
158 UNDERSTANDING YOUR INSTRUMENT PANEL EVIC Control Buttons NOTE: When opening one of the front doors, the EVIC display will turn on the clock and the miles or kilometers Press the SET ESC button briefly to access the menu covered (for versions/markets, where provided) for a and/or go to next screen or to confirm the required menu few seconds.
Page 161 UNDERSTANDING YOUR INSTRUMENT PANEL 159 • See Radio Selecting An Option Of The Main Menu Without Submenu • Speed Display 1. Briefly press the SET ESC button to select the main • Autoclose menu option to set. • Units 2. Press the UP or DOWN button (by single •...
Page 162: Change Engine Oil Indicator System
160 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Briefly press the SET ESC button to select the dis- flash in the EVIC display for approximately 10 seconds played submenu option and to open the relevant setup after a single chime has sounded to indicate the next menu.
Page 163: Trip Computer
UNDERSTANDING YOUR INSTRUMENT PANEL 161 NOTE: If the indicator message illuminates when you New Trip start the vehicle, the oil change indicator system did not To reset: reset. If necessary, repeat this procedure. • Press and hold the TRIP button to reset the system Trip Computer manually.
Page 164: Trip Functions
162 UNDERSTANDING YOUR INSTRUMENT PANEL • Average consumption Start Of Trip Procedure • Instant consumption A With the ignition on, press and hold the TRIP button for over one second to reset. • Average speed A Exit Trip • Travel time A (driving time). To exit the Trip function, wait until all the values have “Trip B”...
Page 165: Values Displayed
UNDERSTANDING YOUR INSTRUMENT PANEL 163 Values Displayed Average Consumption This value shows the approximate average consumption Range since the last reset. This indicates the distance which may be travelled with the fuel remaining in the tank, assuming that driving Instant Consumption conditions will not change.
Page 166: Personal Settings (Customer-Programmable Features)
164 UNDERSTANDING YOUR INSTRUMENT PANEL Personal Settings (Customer-Programmable 2. Briefly press the SET ESC button to go back to the Features) menu screen or press and hold the SET ESC (approxi- mately one second) to go back to the main screen Dimmer without storing settings.
Page 167 UNDERSTANDING YOUR INSTRUMENT PANEL 165 3. When the function is activated (On), briefly press the To cancel the setting, proceed as follows: SET ESC button to display the presently set activation 1. Briefly press the SET ESC button. “On” will flash on speed.
Page 168 166 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Press the UP or DOWN button to select the 4. When accessing the “Time” sub-menu item, briefly setting. press the SET ESC button and “hours” will flash on the display. 3. Briefly press the SET ESC button to go back to the menu screen, or press and hold the SET ESC button 5.
Page 169 UNDERSTANDING YOUR INSTRUMENT PANEL 167 • When accessing the “Mode” submenu, briefly press 2. Press the UP or DOWN button for setting. the SET ESC button. The previously set display format 3. Briefly press the SET ESC button and “month” will will flash on the display.
Page 170 168 UNDERSTANDING YOUR INSTRUMENT PANEL See Radio (Repeat Audio Information) If the radio has BLUE&ME™, refer to the appropriate “BLUE&ME™ User’s Manual” for further information. With this function active, the EVIC display shows infor- mation relevant to the sound system. Speed Display •...
Page 171 UNDERSTANDING YOUR INSTRUMENT PANEL 169 Autoclose Units (Set Units) With this function active, the doors will automatically This function may be used to set the measurement unit in lock at when the vehicle’s speed exceeds 15 mph three submenus: “Distance,” “Temperature” and “Fuel (24 km/h).
Page 172 170 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Briefly press the SET ESC button to return to the 3. When accessing the “Temperature” submenu: briefly sub-menu. press the SET ESC button. Either “°F” or “°C” will appear on the display (according to the previous 7.
Page 173 UNDERSTANDING YOUR INSTRUMENT PANEL 171 To set the required language, proceed as follows: 2. Press the UP or DOWN button for setting. 1. Briefly press the SET ESC button. The previously set 3. Briefly press the SET ESC button to go back to the “language”...
Page 174 Indication) GSI (Gear Shift Indicator) This function will only be displayed after a FIAT Group This function may be used to set the Gear Shift Indicator Automobiles studio has deactivated the S.B.R. system. in two submenus: “Fuel Econ On” and “Fuel Econ Off.”...
Page 175 UNDERSTANDING YOUR INSTRUMENT PANEL 173 2. Press the UP or DOWN button to navigate the brake pressure the driver applied for a short period of two sub-menus. time after the foot has been removed from the brake pedal. 3. Select the required sub-menu and then briefly press the SET ESC button.
Page 176: Sales Code (Rab) Radio
174 UNDERSTANDING YOUR INSTRUMENT PANEL Drivers Door is selected, you must press the RKE trans- SALES CODE (RAB) RADIO mitter UNLOCK button twice to unlock the passenger door. When All Doors is selected, both of the doors will unlock on the first press of the RKE transmitter UNLOCK button.
Page 177: Suggestions
UNDERSTANDING YOUR INSTRUMENT PANEL 175 If the radio has BLUE&ME™, refer to the appropriate WARNING! “BLUE&ME™ User’s Manual” for further information. Having the volume turned up high can cause the The instructions for use are given below and we recom- driver to not be able to hear important traffic sounds, mend you to read them carefully.
Page 178 176 UNDERSTANDING YOUR INSTRUMENT PANEL • Clean every CD thoroughly removing any finger • The use of original CD media is required for the best marks or dust using a soft cloth. Hold CDs by the quality audio production. Correct operation is not outside and clean them from the middle outwards.
Page 179: Technical Specifications
UNDERSTANDING YOUR INSTRUMENT PANEL 177 • The CD player is capable of reading most compression With Alpine Premium Audio system (if equipped): systems currently in use, following the development of • Two 165 mm diameter midwoofer speakers. these systems, the reading of all compression formats •...
Page 180: Quick Guide
178 UNDERSTANDING YOUR INSTRUMENT PANEL Quick Guide Radio Controls BUTTON GENERAL FUNCTIONS MODE Short button press Short button press TUNER AM, FM, SAT (if equipped) source selection Short repeated button press A-B-C Cycles A, B, C presets for AM, FM, SAT (if Short repeated button press equipped) MEDIA...
Page 181 UNDERSTANDING YOUR INSTRUMENT PANEL 179 BUTTON GENERAL FUNCTIONS MODE (Mute/Pause Volume activation/deactivation (Mute/ Short button press Pause) Button) AUDIO Audio adjustments: low tones (BASS), Menu activation: short button press high tones (TREBLE), left/right balance Adjustment type selection: press (BALANCE), front/rear balance (FADER) Adjustment of values: press (Information Song, Artist, Album, Genre, Playlist,...
Page 182 180 UNDERSTANDING YOUR INSTRUMENT PANEL BUTTON RADIO FUNCTIONS MODE Radio Station Search: Automatic search: press buttons (long press for • Automatic Search fast forward) • Manual Search Manual search: press buttons (long press for fast forward) 1 2 3 4 5 Current radio station storing Long button press for memory preset 1 to 5 respectively Stored station recall...
Page 183: General Information
UNDERSTANDING YOUR INSTRUMENT PANEL 181 General Information CD Section • Track selection (forward/backward) The radio offers the following functions: • Fast forward/rewind through tracks Radio Section • PLL tuning with FM/AM bands • CD Display function: display of track number and on mp3 discs (song title, artist) and time elapsed since •...
Page 184: Functions And Adjustments
182 UNDERSTANDING YOUR INSTRUMENT PANEL • Separate bass/treble tone adjustment CD/MP3 Section • MP3-Info function (ID3-TAG) • Right/left channel balancing • Folder selection (previous/next) • Front/rear fader • Track selection (forward/backward) Functions And Adjustments • Fast forward/rewind through tracks Turning The Car Radio On •...
Page 185 UNDERSTANDING YOUR INSTRUMENT PANEL 183 Selecting The Radio Functions Press the button again to deactivate the MUTE func- tion. The volume will gradually increase until it reaches By pressing the TUNER button briefly and repeatedly, the previously set level. the following audio sources can be selected cyclically: When the volume level is changed using the dedicated •...
Page 186 184 UNDERSTANDING YOUR INSTRUMENT PANEL • USER EQUALIZER — if equipped (customized equal- Use the buttons to scroll through the Menu functions. To change the setting of the selected function, ization adjustment) use the buttons. Tone Adjustment The current status of the selected function appears on the Proceed as follows: display.
Page 187 UNDERSTANDING YOUR INSTRUMENT PANEL 185 2. Press the button to set “Balance” in the 3. Press the button to increase the sound coming from AUDIO menu. the rear speakers or the button to increase the sound coming from the front speakers. 3.
Page 188 186 UNDERSTANDING YOUR INSTRUMENT PANEL • “Jazz” (equalizer preset for optimal jazz music sound) Preset/User/Classic/Rock/Jazz Functions — If Equipped When one of the equalizer adjustments is activated the The built-in equalizer can be activated/deactivated. wording “EQ” lights up. When the equalizer function is off, the audio settings can User EQ Settings Function —...
Page 189 UNDERSTANDING YOUR INSTRUMENT PANEL 187 • Sat ID 6. To store the setting, press the MENU or AUDIO buttons. • SiriusXM Telephone Number Menu • System Reset MENU Button Functions • Speed Volume Press the MENU button briefly to activate the Menu •...
Page 190 188 UNDERSTANDING YOUR INSTRUMENT PANEL • Low: function activated (low sensitivity) – If the volume level is equal to or lower than the minimum value, the radio will come on at the • High: function activated (high sensitivity) minimum volume. On Volume Limit •...
Page 191: Radio
UNDERSTANDING YOUR INSTRUMENT PANEL 189 • YES — The default parameters will be restored. Dur- Radio Off Function ing such operation, the wording “Resetting” appears This function makes it possible to set the radio switching on the display. At the end of the operation, the source off mode by choosing between two methods.
Page 192 190 UNDERSTANDING YOUR INSTRUMENT PANEL • 15 in SAT (if so equipped) (5 SATA, 5 SATB, 5 SATC) Frequency Band Selection With the Radio mode active, press the FM or AM tuner To listen to a preset station, select the desired frequency button briefly and repeatedly to select the desired recep- band and then briefly press the corresponding preset tion band.
Page 193: Siriusxm Satellite Radio - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 191 Manual Tuning of sight of the antenna will cause decreased performance. Larger luggage items should be placed as far from the This is used to manually search for stations in the antenna as possible. Do not place items directly on or preselected band.
Page 194 192 UNDERSTANDING YOUR INSTRUMENT PANEL trademarks of SiriusXM Radio Inc. and its subsidiaries. The Program Types available are: All, Pop, Rock, SiriusXM Radio requires a subscription, sold separately Electronic/Dance, Hip-Hop/R&B, Country, Christian, after trial subscription included with vehicle purchase. Jazz/Standards, Classical, Latin/World, Sports, Enter- Prices and programming are provided by SiriusXM and tainment, Talk, News, NPR, Comedy, Family &...
Page 195 Sirius Subscription Issues When Replacing A CAUTION! Sirius Radio Neither SIRIUS nor FIAT is responsible for any When a radio needs to be replaced, the studio will need errors in accuracies in the SIRIUS data services or its the SIRIUS information to order a new radio (even if the use in vehicles.
Page 196: Cd Player
194 UNDERSTANDING YOUR INSTRUMENT PANEL The following are instructions for retrieving the Elec- CD Player Selection tronic Serial Number (ESN) from FIAT 500 NAFTA model To activate the CD player built into the equipment, radios: proceed as follows: To retrieve the ESN of SIRIUS Satellite Receiver Module •...
Page 197 UNDERSTANDING YOUR INSTRUMENT PANEL 195 CD Loading/Ejecting If the CD is not removed from the radio, it will automati- cally be reloaded about 20 seconds later but will not To load the CD, insert it gently into the slot to activate the resume playing until the MEDIA button is pressed to motorized loading system, which will position it cor- select the CD mode.
Page 198: Cd Mp3 Player
196 UNDERSTANDING YOUR INSTRUMENT PANEL Display Information Track Fast Forward/Rewind When the CD player is operating, information will ap- Keep the button pressed down to fast forward the pear on the display with the following meaning: selected track and keep the button pressed down to fast rewind the track.
Page 199 UNDERSTANDING YOUR INSTRUMENT PANEL 197 • The music files should have the extension “.mp3” or MP3 Mode “.wma” files with a different extension will not be In addition to playing regular audio CDs, the radio is also reproduced. enabled to play CDROMs on which compressed audio •...
Page 200 198 UNDERSTANDING YOUR INSTRUMENT PANEL move to the MP3 session while playing by keeping the Selection Of Next/Previous Folder CD button pressed for more than two seconds. Press the button to select a next folder or the but- ton to select the previous folder. The display will show NOTE: When the function is activated the radio may take the number of the folder.
Page 201: Troubleshooting
UNDERSTANDING YOUR INSTRUMENT PANEL 199 • If the MP3 files on a CD-ROM are structured in CD Player sub-folders their structure is compressed to a single The CD Does Not Play level structure, where the sub-folders are taken to the The CD is dirty.
Page 202: Ipod®/Usb/Media Player Control - If
200 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Hands-Free Phone (If Equipped) Refer to the appropriate “BLUE&ME™ User’s Manual” for further information. Personal/Portable Navigation Device (PND) — If Equipped A Personal/Portable Navigation Device (PND) is avail- able as optional equipment for this vehicle, refer to the Navigation User Guide for further information.
Page 203: Steering Wheel Audio Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 201 STEERING WHEEL AUDIO CONTROLS The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and The remote sound system controls are located on the rear mode of the sound system. Pressing the top of the rocker surface of the steering wheel.
Page 204: Radio Operation
202 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation Operating Instructions — Hands-Free Phone (If Equipped) Pressing the top of the switch will “Seek” up for the next listenable station and pressing the bottom of the switch Refer to the appropriate Blue&Me™ User’s Manual for will “Seek”...
Page 205: Radio Operation And Mobile Phones
UNDERSTANDING YOUR INSTRUMENT PANEL 203 5. Store the disc in its case after playing. RADIO OPERATION AND MOBILE PHONES Under certain conditions, the mobile phone being on in 6. Do not expose the disc to direct sunlight. your vehicle can cause erratic or noisy performance from 7.
Page 206: Manual Heating And Air Conditioning
204 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Heating And Air Conditioning 1. Temperature Control Rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial to the left into the blue area of the scale indicates cooler temperatures, while rotating to the right into the red area indicates warmer temperatures.
Page 207 UNDERSTANDING YOUR INSTRUMENT PANEL 205 • Panel NOTE: Air is directed through the outlets in the instru- • Continuous use of the Recirculation mode may make ment panel. These outlets can be adjusted to direct the inside air stuffy and window fogging may occur. airflow.
Page 208: Automatic Temperature Control (Atc) - If Equipped
206 UNDERSTANDING YOUR INSTRUMENT PANEL to the windshield. This setting is good for maintaining MAX A/C comfort while reducing moisture on the windshield. For maximum cooling, use the A/C and recirculation • Defrost modes at the same time. Air is directed through the windshield and side ECONOMY MODE window demister outlets.
Page 209 UNDERSTANDING YOUR INSTRUMENT PANEL 207 2. A/C Button Press and release to change the current Air Conditioning (A/C) setting. Performing this function will cause the ATC to switch into manual mode. 3. Temperature Control Up Button Provides temperature up control. Push the button for warmer temperature settings.
Page 210 208 UNDERSTANDING YOUR INSTRUMENT PANEL reducing moisture on the windshield. Performing this NOTE: The center instrument panel outlets can be aimed function will cause the ATC to switch into manual mode. so that they are directed toward the rear seat passengers for maximum airflow to the rear.
Page 211 UNDERSTANDING YOUR INSTRUMENT PANEL 209 NOTE: 3. When the system is set up for your comfort level, it is not necessary to change the settings. You will experi- When in Defrost mode, the Recirculation button will ence the greatest efficiency by simply allowing the flash if pressed.
Page 212 210 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Operation The blower fan speed can be set to any fixed speed by pressing the blower control up or down buttons. The fan This system offers a full complement of manual override will now operate at a fixed speed until additional speeds features.
Page 213 UNDERSTANDING YOUR INSTRUMENT PANEL 211 Floor Mode Defrost Mode Air comes from the floor outlets. A slight amount Air comes from the windshield and side window of air is directed through the defrost and side demister outlets. Use Defrost mode with maxi- window demister outlets.
Page 214: Operating Tips
212 UNDERSTANDING YOUR INSTRUMENT PANEL outlets. If Economy mode is desired, press the A/C selected. Push the button a second time to turn off the button to turn off the A/C mode in the ATC display and Recirculation mode LED and allow outside air into the deactivate the A/C system.
Page 215 UNDERSTANDING YOUR INSTRUMENT PANEL 213 control and blower speed to maintain comfort. Higher a heavy load or high heat conditions, it may use Recir- blower speeds will reduce fogging. Interior fogging on culation A/C mode to provide additional comfort while the windshield can be quickly removed by selecting the in automatic mode.
Page 217: Starting And Operating
STARTING AND OPERATING CONTENTS STARTING PROCEDURES ....219 Downshifting ......223 Manual Transmission –...
Page 218 216 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES ..234 ELECTRONIC BRAKE CONTROL SYSTEM ..244 Acceleration ......234 Anti-Lock Brake System (ABS) .
Page 219 STARTING AND OPERATING 217 TIRES — GENERAL INFORMATION..263 Life Of Tire ......270 Tire Pressure .
Page 220 218 STARTING AND OPERATING E-85 Usage In Non-Flex Fuel Vehicles ..282 ADDING FUEL ......285 MMT In Gasoline .
Page 221: Starting Procedures
STARTING AND OPERATING 219 STARTING PROCEDURES Manual Transmission – If Equipped Before starting your vehicle, adjust your seat, adjust both Apply the parking brake, place the shift lever in NEU- inside and outside mirrors, and fasten your seat belts. TRAL, and press the clutch pedal before starting the vehicle.
Page 222: Cold Weather Operation
220 STARTING AND OPERATING Turn the ignition switch to the AVV (START) position and reminder to avoid possible crank delays at the next cold release it when the engine starts. If the engine fails to start start. within 10 seconds, turn the ignition switch to the STOP (OFF/LOCK) position, wait 10 to 15 seconds, then repeat CAUTION! the “Normal Starting”...
Page 223: After Starting
STARTING AND OPERATING 221 MANUAL TRANSMISSION — IF EQUIPPED CAUTION! Five-Speed Manual Transmission • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic trans- WARNING! mission cannot be started this way. Unburned fuel could enter the catalytic converter and once the You or others could be injured if you leave the engine has started, ignite and damage the converter...
Page 224 222 STARTING AND OPERATING Use each gear in numerical order; do not skip a gear. Be sure the transmission is in first gear, not third, when starting from a standing position. Damage to the clutch can result from starting in third gear. For most city driving, you will find it easier to use only the lower gears.
Page 225: Recommended Shift Speeds
STARTING AND OPERATING 223 NOTE: Manual Transmission Recommended Shift Speeds • Clashing REVERSE gear, especially if vehicle is mov- Units In mph (km/h) ing, can result in transmission damage. Engine Accel- 1 to 2 2 to 3 3 to 4 4 to 5 Size era-...
Page 226: Automatic Transmission - If
224 STARTING AND OPERATING AUTOMATIC TRANSMISSION — IF EQUIPPED CAUTION! CAUTION! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may Damage to the transmission may occur if the follow- cause the engine to overspeed if too low of a gear is ing precautions are not observed: selected and the clutch pedal is released.
Page 227 STARTING AND OPERATING 225 WARNING! WARNING! (Continued) • Unintended movement of a vehicle could injure • It is dangerous to shift out of PARK or NEUTRAL those in or near the vehicle. As with all vehicles, if the engine speed is higher than idle speed. If you should never exit a vehicle while the engine is your foot is not firmly pressing the brake pedal, the running.
Page 228: Key Ignition Park Interlock
226 STARTING AND OPERATING when the ignition is in the OFF position, and once WARNING! (Continued) removed, the shift lever is locked in PARK. • Never leave children alone in a vehicle, or with Brake/Transmission Shift Interlock System access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a This vehicle is equipped with a Brake Transmission Shift number of reasons.
Page 229: Gear Ranges
STARTING AND OPERATING 227 The electronically-controlled transmission provides a Only shift from DRIVE to PARK or REVERSE when the precise shift schedule. The transmission electronics are accelerator pedal is released and the vehicle is stopped. self-calibrating; therefore, the first few shifts on a new Be sure to keep your foot on the brake pedal when vehicle may be somewhat abrupt.
Page 230 228 STARTING AND OPERATING NOTE: After selecting any gear range, wait a moment to WARNING! allow the selected gear to engage before accelerating. • Never use the PARK position as a substitute for the This is especially important when the engine is cold. parking brake.
Page 231 STARTING AND OPERATING 229 WARNING! (Continued) WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL • When leaving the vehicle, always remove the igni- if the engine speed is higher than idle speed. If tion key and lock your vehicle. •...
Page 232 230 STARTING AND OPERATING • With brake pedal released, verify that the shift lever CAUTION! will not move out of PARK. • Before moving the shift lever out of PARK, you REVERSE must turn the ignition switch from the OFF posi- This range is for moving the vehicle backward.
Page 233 STARTING AND OPERATING 231 automatically upshifts through all forward gears. The WARNING! (Continued) DRIVE position provides optimum driving characteris- practices that limit your response to changing traffic tics under all normal operating conditions. or road conditions. You might lose control of the When frequent transmission shifting occurs (such as vehicle and have a collision.
Page 234 232 STARTING AND OPERATING During cold temperatures, transmission operation may 1. Stop the vehicle. be modified depending on engine coolant temperature. 2. Shift the transmission into PARK. Normal operation will resume once the engine tempera- ture has risen to a suitable level. 3.
Page 235: Autostick® - If Equipped
STARTING AND OPERATING 233 AUTOSTICK® — IF EQUIPPED NOTE: In AutoStick® mode, the transmission will only shift up or down when the driver moves the shift lever AutoStick® is a driver-interactive transmission feature rearward (+) or forward (-), except as described below. providing manual shift control, giving you more control •...
Page 236: Driving On Slippery Surfaces
234 STARTING AND OPERATING • The system will ignore shift commands that would AutoStick® position at any time without taking your cause engine lugging or overspeed. An audible beep foot off the accelerator pedal. will sound if an inappropriate gear is requested. WARNING! •...
Page 237: Traction
STARTING AND OPERATING 235 2. Slow down if the road has standing water or puddles. WARNING! 3. Replace the tires when tread wear indicators first Rapid acceleration on slippery surfaces is dangerous. become visible. Unequal traction can cause sudden pulling of the 4.
Page 238: Flowing/Rising Water
236 STARTING AND OPERATING Flowing/Rising Water CAUTION! • Always check the depth of the standing water WARNING! before driving through it. Never drive through Do not drive on or across a road or path where water standing water that is deeper than the bottom of is flowing and/or rising (as in storm run-off).
Page 239 STARTING AND OPERATING 237 CAUTION! (Continued) WARNING! • Driving through standing water may cause damage • Driving through standing water limits your vehi- to your vehicle’s drivetrain components. Always cle’s traction capabilities. Do not exceed 5 mph inspect your vehicle’s fluids (i.e., engine oil, trans- (8 km/h) when driving through standing water.
Page 240: Power Steering
238 STARTING AND OPERATING POWER STEERING If the Steering icon is displayed and the “POWER STEER- ING SYSTEM OVER TEMP” message is displayed on the The electric power steering system will give you good EVIC screen, they indicate that extreme steering maneu- vehicle response and increased ease of maneuverability vers may have occurred which caused an over tempera- in tight spaces.
Page 241: Parking Brake
STARTING AND OPERATING 239 NOTE: • Even if the power steering assistance is no longer operational, it is still possible to steer the vehicle. Under these conditions there will be a substantial increase in steering effort, especially at low speeds and during parking maneuvers.
Page 242 240 STARTING AND OPERATING should always be applied whenever the driver is not in WARNING! (Continued) the vehicle. • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake WARNING! failure and a collision. •...
Page 243: Sport Mode
STARTING AND OPERATING 241 SPORT MODE Manual Transmission – If Equipped The Sport mode increases steering feedback to the driver with slight increases in effort and throttle pedal-to-engine response. This driving mode is useful while driving on twisty roads where more steering precision is desired in spirited cornering.
Page 244: Automatic Transmission - If Equipped
242 STARTING AND OPERATING Automatic Transmission – If Equipped The Sport mode increases steering feedback to the driver with slight increase in effort and changes the transmis- sion shift schedules for more aggressive shifting. This driving mode is useful while driving on twisty roads where more steering precision is desired in spirited cornering.
Page 245: Brake System
STARTING AND OPERATING 243 BRAKE SYSTEM Four-Wheel Anti-Lock Brake System (ABS) In the event power assist is lost for any reason (for The Four-Wheel ABS is designed to aid the driver in example; repeated brake applications with the engine maintaining vehicle control under adverse braking con- off), the brakes will still function.
Page 246: Electronic Brake Control System
244 STARTING AND OPERATING When you are in a severe braking condition involving the WARNING! use of the ABS, you will experience some pedal drop as • Pumping the Anti-Lock Brakes will diminish their the vehicle comes to a stop. This is the result of the system reverting to the base brake system.
Page 247: Anti-Lock Brake System (Abs)
STARTING AND OPERATING 245 Anti-Lock Brake System (ABS) “pump” the brakes). Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal This system aids the driver in maintaining vehicle control is released, the BAS is deactivated. under adverse braking conditions.
Page 248: Traction Control System (Tcs)
246 STARTING AND OPERATING Traction Control System (TCS) period of time after the driver takes his foot off the brake pedal. If the driver does not apply the throttle during this This system monitors the amount of wheel spin of each of short period of time, the system will release brake the driven wheels.
Page 249: Electronic Stability Control (Esc)
STARTING AND OPERATING 247 Electronic Stability Control (ESC) WARNING! This system enhances directional control and stability of There may be situations on minor hills (i.e., less than the vehicle under various driving conditions. ESC cor- 8%), with a loaded vehicle, or while pulling a trailer, rects for oversteering or understeering of the vehicle by when the system will not activate and slight rolling applying the brake of the appropriate wheel to assist in...
Page 250 248 STARTING AND OPERATING ESC Off Switch (Automatic Transmission) ESC Off Switch (Manual Transmission) NOTE: The ESC Off switch is located left of the steering column (Manual Transmission Only).
Page 251 STARTING AND OPERATING 249 ESC Operating Modes WARNING! The ESC system has two available operating modes. The Electronic Stability Control (ESC) cannot pre- Full On vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by This is the normal operating mode for ESC.
Page 252: Esc Activation/Malfunction Indicator Light And Esc Off Indicator Light
250 STARTING AND OPERATING To turn ESC on again, momentarily press the switch WARNING! again. This will restore the normal ESC On mode of • When in “Partial Off” mode, the TCS functionality operation. of ESC, (except for the limited slip feature de- NOTE: To improve the vehicle’s traction when driving scribed in the TCS section), has been disabled and with snow chains, or starting off in deep snow, sand or...
Page 253 STARTING AND OPERATING 251 on continuously with the engine running, a malfunction NOTE: has been detected in the ESC system. If this light remains • The ESC Activation/Malfunction Indicator Light and on after several ignition cycles, and the vehicle has been the ESC OFF Indicator Light come on momentarily driven several miles (kilometers) at speeds greater than each time the ignition switch is turned ON.
Page 254: Tire Safety Information
252 STARTING AND OPERATING TIRE SAFETY INFORMATION NOTE: Tire Markings • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
Page 255 STARTING AND OPERATING 253 • High flotation tire sizing is based on U.S. design compact spare tires have the letter “T” or “S” molded into the sidewall preceding the size designation. Ex- standards and it begins with the tire diameter molded ample: T145/80D18 103M.
Page 256 254 STARTING AND OPERATING EXAMPLE: 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 257: Tire Identification Number (Tin)
STARTING AND OPERATING 255 Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on The TIN may be found on one or both sides of the tire, the outboard side, then you will find it on the inboard however, the date code may only be on one side.
Page 258: Tire Terminology And Definitions
256 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 01 = Number representing the year in which the tire was manufactured (two digits) — 01 means the year 2001 — Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.
Page 259 STARTING AND OPERATING 257 Term Definition Maximum Inflation Pressure The maximum inflation pressure is the maximum permissible cold tire inflation pressure for this tire. The maximum inflation pressure is molded into the sidewall. Recommended Cold Tire Inflation Vehicle manufacturer’s recommended cold tire inflation pressure Pressure as shown on the tire placard.
Page 260: Tire Loading And Tire Pressure
258 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. B-Pillar Location for Tire And Loading Information Placard...
Page 261 STARTING AND OPERATING 259 Tire And Loading Information Placard 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading...
Page 262 260 STARTING AND OPERATING To determine the maximum loading conditions of your 4. The resulting figure equals the available amount of vehicle, locate the statement “The combined weight of cargo and luggage load capacity. For example, if occupants and cargo should never exceed XXX lbs or “XXX”...
Page 263 STARTING AND OPERATING 261 NOTE: • The following table shows examples on how to calcu- late total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load carry capacity of your vehicle.
Page 264 262 STARTING AND OPERATING...
Page 265: Tires - General Information
STARTING AND OPERATING 263 Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
Page 266: Tire Inflation Pressures
264 STARTING AND OPERATING stability of the vehicle and can produce a feeling of WARNING! (Continued) sluggish response or over responsiveness in the steering. • Unequal tire pressures from one side of the vehicle Unequal tire pressures from side to side may cause erratic to the other can cause the vehicle to drift to the and unpredictable steering response.
Page 267: Tire Pressures For High Speed Operation
STARTING AND OPERATING 265 Tire pressures change by approximately 1 psi (7 kPa) per CAUTION! 12° F (7° C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in After inspecting or adjusting the tire pressure, al- the winter.
Page 268: Radial Ply Tires
266 STARTING AND OPERATING loading may be required for high-speed vehicle opera- Radial Ply Tires tion. Refer to your authorized tire or original equipment vehicle studio for recommended safe operating speeds, WARNING! loading and cold tire inflation pressures. Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle WARNING! poorly.
Page 269: All Season Tires - If Equipped
STARTING AND OPERATING 267 Consult an authorized tire dealer for tire repairs and on ice. Summer tires will not contain the all season additional information. designation or mountain/snowflake symbol on the tire sidewall. Use summer tires only in sets of four; failure to Damaged Run Flat tires, or Run Flat tires that have do so may adversely affect the safety and handling of experienced a loss of pressure should be replaced imme-...
Page 270: Spare Tire Matching Original Equipped Tire And Wheel - If Equipped
268 STARTING AND OPERATING original equipment or an authorized tire dealer for Compact Spare Tire recommended safe operating speeds, loading and cold The compact spare is for temporary emergency use with tire inflation pressures. radial tires. It is engineered to be used on your style While studded tires improve performance on ice, skid vehicle only.
Page 271: Tire Spinning
STARTING AND OPERATING 269 Do not install a wheel cover or attempt to mount a Tire Spinning conventional tire on the compact spare wheel, since the When stuck in mud, sand, snow, or ice conditions, do not wheel is designed specifically for the compact spare. spin your vehicle’s wheels above 30 mph (48 km/h) or Do not install more than one compact spare tire/wheel for longer than 30 seconds continuously without stop-...
Page 272: Tread Wear Indicators
270 STARTING AND OPERATING Tread Wear Indicators These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth Tread wear indicators are in the original equipment tires becomes 1/16 in (2 mm). When the tread is worn to the to help you in determining when your tires should be tread wear indicators, the tire should be replaced.
Page 273: Replacement Tires
STARTING AND OPERATING 271 Information placard or the Vehicle Certification Label for WARNING! the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original Tires and the spare tire should be replaced after six equipment tire sidewall.
Page 274: Tire Chains
272 STARTING AND OPERATING WARNING! WARNING! (Continued) • Failure to equip your vehicle with tires having • Do not use a tire, wheel size or rating other than adequate speed capability can result in sudden tire that specified for your vehicle. Some combinations failure and loss of vehicle control.
Page 275 STARTING AND OPERATING 273 CAUTION! CAUTION! (Continued) • Install chains on the front wheels as tightly as To avoid damage to your vehicle or tires, observe the possible and then retighten after driving about 0.5 following precautions: mile (0.8 km). •...
Page 276: Tire Rotation Recommendations
274 STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS The suggested rotation method is the “rearward cross” shown in the following diagram. This rotation pattern The tires on the front and rear of your vehicle operate at does not apply to some directional tires that must not be different loads and perform different steering, driving, reversed.
Page 277: Tire Pressure Monitoring System
STARTING AND OPERATING 275 TIRE PRESSURE MONITORING SYSTEM (TPMS) also increase as the vehicle is driven - this is normal and there should be no adjustment for this increased pres- The Tire Pressure Monitor System (TPMS) will warn the sure. driver of a low tire pressure based on the vehicle recom- mended cold tire pressure.
Page 278 276 STARTING AND OPERATING driven for up to 20 minutes above 15 mph (24 km/h) in CAUTION! order for the TPMS to receive this information. • The TPMS has been optimized for the original For example, your vehicle may have a recommended equipment tires and wheels.
Page 279: Base System
STARTING AND OPERATING 277 • Seasonal temperature changes will affect tire pressure, NOTE: and the TPMS will monitor the actual tire pressure in • The TPMS is not intended to replace normal tire care the tire. and maintenance, or to provide warning of a tire failure or condition.
Page 280 278 STARTING AND OPERATING • Four Tire Pressure Monitoring Sensors Check TPMS Warnings • Tire Pressure Monitoring Telltale Light The Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds and remain on solid when a system Tire Pressure Monitoring Low Pressure Warnings fault is detected, an audible chime will be activated and The Tire Pressure Monitoring Telltale Light will illumi-...
Page 281: Enhanced System- If Equipped
STARTING AND OPERATING 279 5. Using wheels/tires not equipped with TPM sensors. 4. This occurs for each subsequent ignition key cycle, a chime will sound and the Tire Pressure Monitoring NOTE: Your vehicle is equipped with a compact spare Telltale Light will flash on and off for 75 seconds and wheel and tire assembly.
Page 282: General Information
280 STARTING AND OPERATING pressure menu command in the instrument cluster. Refer FUEL REQUIREMENTS to the instrument panel features section of the owners manual. Your vehicle is designed to meet all emis- sion regulations and provide satisfactory General Information fuel economy and performance when us- This device complies with Part 15 of the FCC rules and ing high-quality unleaded gasoline having RSS 210 of Industry Canada.
Page 283: Fuel Requirements - 1.4L Turbo
STARTING AND OPERATING 281 FUEL REQUIREMENTS – 1.4L Turbo Reformulated Gasoline Many areas of the country require the use of cleaner This engine is designed to meet all emis- burning gasoline referred to as “Reformulated Gasoline.” sion regulations and provide satisfactory Reformulated gasolines contain oxygenates and are spe- fuel economy and performance when us- cifically blended to reduce vehicle emissions and im-...
Page 284: E-85 Usage In Non-Flex Fuel Vehicles
282 STARTING AND OPERATING • OBD II “Malfunction Indicator Light” on CAUTION! • poor engine performance Do not use gasoline containing Methanol or E-85 • poor cold start and cold drivability Ethanol. Use of these blends may result in starting and driveability problems and may damage critical •...
Page 285: Materials Added To Fuel
STARTING AND OPERATING 283 blended with MMT provides no performance advantage Fuel System Cautions beyond gasoline of the same octane number without MMT. Gasoline blended with MMT reduces spark plug CAUTION! life and reduces emissions system performance in some Follow these guidelines to maintain your vehicle’s vehicles.
Page 286: Carbon Monoxide Warnings
284 STARTING AND OPERATING CAUTION! (Continued) WARNING! (Continued) • The use of fuel additives, which are now being sold as • Do not inhale exhaust gases. They contain carbon octane enhancers, is not recommended. Most of these monoxide, a colorless and odorless gas, which can products contain high concentrations of methanol.
Page 287: Adding Fuel
STARTING AND OPERATING 285 ADDING FUEL CAUTION! Fuel Filler Cap (Gas Cap) • Damage to the fuel system or emission control The gas cap is located on the passenger side of the system could result from using an improper fuel vehicle.
Page 288: Loose Fuel Filler Cap Message
286 STARTING AND OPERATING Loose Fuel Filler Cap Message WARNING! (Continued) After fuel has been added, the vehicle diagnostic system • Never add fuel when the engine is running. It may can determine if the fuel filler cap is possibly loose, cause the MIL to turn on and could cause a fire.
Page 289: Recreational Towing
STARTING AND OPERATING 287 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF the Ground Manual Transmission Automatic Transmission Flat Tow NONE Transmission in NOT ALLOWED NEUTRAL Dolly Tow Front Rear NOT ALLOWED NOT ALLOWED On Trailer NOTE: Vehicles equipped with manual transmissions CAUTION!
Page 290 288 STARTING AND OPERATING NOTE: This vehicle may be towed on a flatbed or vehicle trailer provided all four wheels are OFF the ground. CAUTION! Towing this vehicle in violation of the above require- ments can cause severe transmission damage. Dam- age from improper towing is not covered under the New Vehicle Limited Warranty.
Page 291: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS HAZARD WARNING FLASHERS ...291 Spare Tire Removal ....304 IF YOUR ENGINE OVERHEATS .
Page 292 290 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE ...321 ENHANCED ACCIDENT RESPONSE SYSTEM ......323 Automatic Transmission .
Page 293: Hazard Warning Flashers
WHAT TO DO IN EMERGENCIES 291 HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel below the radio. potential for overheating by taking the appropriate ac- tion.
Page 294: Tirefit Kit - If Equipped
292 WHAT TO DO IN EMERGENCIES supplement to the radiator and aids in removing heat WARNING! from the engine cooling system. You or others can be badly burned by hot engine CAUTION! coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, Driving with a hot cooling system could damage do not open the hood until the radiator has had time...
Page 295: Tirefit Storage
WHAT TO DO IN EMERGENCIES 293 TIREFIT Storage TIREFIT Kit Components And Operation The TIREFIT kit is located under the front driver’s seat. TIREFIT Components TIREFIT Kit Location 1. Sealant Bottle 2. Deflation Button 3. Pressure Gauge...
Page 296: Tirefit Usage Precautions
294 WHAT TO DO IN EMERGENCIES • When the TIREFIT sealant is in a liquid form, clean 4. Power Button water, and a damp cloth will remove the material from 5. Mode Select Knob the vehicle or tire and wheel components. Once the 6.
Page 297 WHAT TO DO IN EMERGENCIES 295 • Do not lift or carry the TIREFIT kit by the hoses. WARNING! (Continued) – If you are unsure of the condition of the tire or WARNING! the wheel. • Do not attempt to seal a tire on the side of the •...
Page 298: Sealing A Tire With Tirefit
296 WHAT TO DO IN EMERGENCIES Sealing A Tire With TIREFIT WARNING! (Continued) (A) Whenever You Stop To Use TIREFIT: • Take care not to allow the contents of TIREFIT to come in contact with hair, eyes, or clothing. TIRE- 1.
Page 299 WHAT TO DO IN EMERGENCIES 297 (B) Setting Up To Use TIREFIT: (C) Injecting TIREFIT Sealant Into The Deflated Tire: 1. Turn the Mode Select Knob (5) to the Sealant Mode • Always start the engine before turning ON the TIRE- position.
Page 300 298 WHAT TO DO IN EMERGENCIES the Sealant Hose (6) to the valve stem. Check that the If the sealant (white fluid) does flow through the Mode Select Knob (5) is in the Sealant Mode position Sealant Hose (6): and not Air Mode. Press the Power Button (4) to turn 1.
Page 301 WHAT TO DO IN EMERGENCIES 299 If the tire does not inflate to at least 26 psi (1.8 Bar) 3. Immediately disconnect the Sealant Hose (6) from the pressure within 15 minutes: valve stem, reinstall the cap on the fitting at the end of the hose, and place the TIREFIT kit in the vehicle •...
Page 302 300 WHAT TO DO IN EMERGENCIES (D) Drive Vehicle: 1. Turn the Mode Select Knob (5) to the Air Mode position. Immediately after injecting sealant and inflating the tire, drive the vehicle 5 miles (8 km) or 10 minutes to ensure 2.
Page 303 WHAT TO DO IN EMERGENCIES 301 If the tire pressure is 19 psi (1.3 Bar) or higher: 5. Replace the Sealant Bottle (1) and Sealant Hose (6) assembly at your authorized studio as soon as pos- 1. Press the Power Button (4) to turn on TIREFIT and sible.
Page 304: Jacking And Tire Changing - If Equipped
302 WHAT TO DO IN EMERGENCIES 5. Position the new Sealant Bottle (1) in the housing so JACKING AND TIRE CHANGING — IF EQUIPPED that the Sealant Hose (6) aligns with the hose slot in the front of the housing. Press the bottle into the WARNING! housing.
Page 305: Jack Location
WHAT TO DO IN EMERGENCIES 303 WARNING! (Continued) • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas.
Page 306: Spare Tire Removal
304 WHAT TO DO IN EMERGENCIES Spare Tire Removal The spare tire is stowed to the underbody below the cargo area. 1. Remove the plug located in the rear cargo area. Winch Access Plug Center Location 2. Fit the wrench tool over the drive nut. Use the wrench to rotate the nut counterclockwise until the spare is on the ground with enough slack in the cable to allow you to pull the tire out from under the vehicle.
Page 307 WHAT TO DO IN EMERGENCIES 305 3. Pull the spare tire out from under the vehicle. Lowering/Raising Spare Tire Spare Tire CAUTION! The winch mechanism is designed for use with the jack wrench tool only. Use of an air wrench or other power tools is not recommended and they can dam- age the winch.
Page 308 306 WHAT TO DO IN EMERGENCIES 4. When the spare is clear, remove the knob or plastic 5. Tilt the retainer at the end of the cable and pull it molded nut by rotating it counter-clockwise. through the center of the wheel. Plastic Molded Nut Retainer...
Page 309: Preparations For Jacking
WHAT TO DO IN EMERGENCIES 307 Preparations For Jacking 6. Block both the front and rear of the wheel diagonally opposite the jacking position. For 1. Park the vehicle on a firm level surface, avoiding ice or example, if changing the right front slippery areas.
Page 310: Jacking Instructions
308 WHAT TO DO IN EMERGENCIES Jacking Instructions WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a WARNING! jack. • Do not get under the vehicle when it is on a jack. If Carefully follow these tire changing warnings to help prevent personal injury or damage to your you need to get under a raised vehicle, take it to a...
Page 311 WHAT TO DO IN EMERGENCIES 309 2. Loosen, but do not remove, the wheel bolts by turning them to the left one turn while the wheel is still on the ground. NOTE: There are front and rear jacking locations on each side of the body (as indicated by the triangular lift point Jack Warning Label symbol on the sill molding).
Page 312 310 WHAT TO DO IN EMERGENCIES 3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed.
Page 313 WHAT TO DO IN EMERGENCIES 311 WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 4. Using the swivel wrench, raise the vehicle by turning the jack screw to the right.
Page 314 312 WHAT TO DO IN EMERGENCIES 5. Remove the wheel bolts and pull the wheel off the WARNING! hub. For vehicles equipped with aluminum wheels, the center caps must be removed to remove the wheel To avoid possible personal injury, handle the wheel bolts.
Page 315 WHAT TO DO IN EMERGENCIES 313 7. Lower the vehicle by turning the jack screw to the left. WARNING! 8. Finish tightening the bolts. Push down on the wrench A loose tire or jack thrown forward in a collision or while tightening the wheel bolts.
Page 316: Spare Tire Stowage
314 WHAT TO DO IN EMERGENCIES Spare Tire Stowage NOTE: When using a portable battery booster pack, follow the manufacturer’s operating instructions and Reverse instructions of the spare removal section. precautions. Rotate the jack wrench tool on the winch drive nut clockwise until effort becomes heavy and an audible click WARNING! is heard indicating the spare is properly stowed.
Page 317 WHAT TO DO IN EMERGENCIES 315 shield. To allow jump-starting, there are remote battery WARNING! posts located on the left side of the engine compartment. • Take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is ON.
Page 318: Jump-Starting Procedure
316 WHAT TO DO IN EMERGENCIES 3. Remove the protective cover over the remote positive Jump-Starting Procedure (+) battery post. To remove the cover, press the locking tab and pull upward on the cover. WARNING! 4. If using another vehicle to jump-start the battery, park Failure to follow this procedure could result in per- the vehicle within the jumper cables reach, set the sonal injury or property damage due to battery ex-...
Page 319 WHAT TO DO IN EMERGENCIES 317 3. Connect the negative end (-) of the jumper cable to the 6. Disconnect the negative (-) jumper cable from the negative (-) post of the booster battery. engine ground (-) of the vehicle with the discharged battery.
Page 320: Freeing A Stuck Vehicle
318 WHAT TO DO IN EMERGENCIES motion, without spinning the wheels, or racing the CAUTION! engine. Accessories plugged into the vehicle power outlets CAUTION! draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if Racing the engine or spinning the wheels may lead to plugged in long enough without engine operation, transmission overheating and failure.
Page 321: Shift Lever Override
WHAT TO DO IN EMERGENCIES 319 CAUTION! WARNING! (Continued) explode and injure someone. Do not spin your vehi- • When “rocking” a stuck vehicle by shifting be- cle’s wheels faster than 30 mph (48 km/h) or for tween DRIVE/2nd gear and REVERSE, do not spin longer than 30 seconds continuously without stop- the wheels faster than 15 mph (24 km/h), or drive- ping when you are stuck and do not let anyone near...
Page 322 320 WHAT TO DO IN EMERGENCIES 3. Remove the shift lever override access cover (located 4. Press and maintain firm pressure on the brake pedal. on the right side of the shift lever housing) by prying 5. Insert a small screwdriver or similar tool into the at the bottom edge of the cover.
Page 323 WHAT TO DO IN EMERGENCIES 321 TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial wrecker service. Towing Wheels OFF The AUTOMATIC TRANSMISSION MANUAL TRANSMISSION Condition Ground Flat Tow NONE If transmission is operable: If transmission is operable: •...
Page 324 322 WHAT TO DO IN EMERGENCIES If the ignition key is unavailable, or the battery is CAUTION! discharged, see “Shift Lever Override” in “What To Do In • DO NOT flat tow any vehicle equipped with an Emergencies” for instructions on shifting the automatic transmission out of PARK for towing.
Page 325 WHAT TO DO IN EMERGENCIES 323 • Turn on the interior lights, which remain on as long as CAUTION! the battery has power or until the ignition key is removed. Towing this vehicle in violation of the above require- ments can cause severe transmission damage. Dam- •...
Page 326 324 WHAT TO DO IN EMERGENCIES In order to move your vehicle to the side of the road you 5. Turn Right Turn Signal Right Turn Light is ON must follow the system reset procedure. Switch ON. SOLID. Left Turn Light BLINKS.
Page 327: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS ENGINE COMPARTMENT — 1.4L ..327 Engine Air Cleaner Filter ....336 ENGINE COMPARTMENT — 1.4L TURBO ..328 Maintenance-Free Battery .
Page 328 326 MAINTAINING YOUR VEHICLE Automatic Transmission – If Equipped ..356 Front Turn Signal, Parking And Daytime Running Lamps..... . .372 Appearance Care And Protection From Corrosion .
Page 329: Engine Compartment - 1.4L
MAINTAINING YOUR VEHICLE 327 ENGINE COMPARTMENT — 1.4L 1 — Engine Coolant Reservoir 5 — Battery 2 — Engine Oil Dipstick 6 — Air Cleaner Filter 3 — Brake Fluid Reservoir 7 — Engine Oil Fill 4 — Front Distribution Unit (Fuses) 8 —...
Page 330: Engine Compartment - 1.4L Turbo
328 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 1.4L TURBO 1 — Engine Coolant Reservoir 5 — Battery 2 — Engine Oil Dipstick 6 — Engine Oil Fill 3 — Brake Fluid Reservoir 7 — Washer Fluid Reservoir 4 — Front Distribution Unit (Fuses)
Page 331: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 329 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors further damage to the emission control system. It the performance of the emissions, engine, and automatic could also affect fuel economy and drivability.
Page 332 330 MAINTAINING YOUR VEHICLE Indicator Light (MIL)” is functioning and is not on when 3. As soon as you turn the ignition switch to the ON the engine is running, and that the OBD II system is position, you will see the MIL symbol come on as part ready for testing.
Page 333: Replacement Parts
MAINTAINING YOUR VEHICLE 331 you may need to do nothing more than drive your STUDIO SERVICE vehicle as you normally would in order for your OBD II Your authorized studio has the qualified service person- system to update. A recheck with the above test routine nel, special tools, and equipment to perform all service may then indicate that the system is now ready.
Page 334: Maintenance Procedures
332 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Failure to properly maintain your vehicle or per- You can be badly injured working on or around a motor vehicle. Only do service work for which you form repairs and service when necessary could have the knowledge and the proper equipment.
Page 335: Engine Oil
MAINTAINING YOUR VEHICLE 333 Engine Oil CAUTION! Checking Oil Level Do not overfill the engine with oil. Overfilling the To assure proper engine lubrication, the engine oil must engine with oil will cause oil aeration, which can be maintained at the correct level. Check the oil level at lead to loss of oil pressure and an increase in oil regular intervals, such as every fuel stop.
Page 336 334 MAINTAINING YOUR VEHICLE Engine Oil Selection CAUTION! For best performance and maximum protection under all Do not use chemical flushes in your engine oil as the types of operating conditions, the manufacturer only chemicals can damage your engine. Such damage is recommends engine oils that are API Certified and meet not covered by the New Vehicle Limited Warranty.
Page 337 MAINTAINING YOUR VEHICLE 335 engine oil filler cap location, refer to “Engine Compart- Synthetic Engine Oils ment” in “Maintaining Your Vehicle” for further informa- You may use synthetic engine oils provided the recom- tion. mended oil quality requirements are met, and the recom- mended maintenance intervals for oil and filter changes Engine Oil Viscosity - 1.4L Turbo (SAE Grade) are followed.
Page 338: Engine Oil Filter
336 MAINTAINING YOUR VEHICLE station or governmental agency for advice on how and WARNING! where used oil and oil filters can be safely discarded in your area. The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine Engine Oil Filter backfire.
Page 339: Maintenance-Free Battery
MAINTAINING YOUR VEHICLE 337 Maintenance-Free Battery WARNING! (Continued) Your vehicle is equipped with a maintenance-free battery. • Battery gas is flammable and explosive. Keep You will never have to add water, nor is periodic main- flame or sparks away from the battery. Do not use tenance required.
Page 340: Air Conditioner Maintenance
338 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance CAUTION! For best possible performance, your air conditioner • It is essential when replacing the cables on the should be checked and serviced by an authorized studio battery that the positive cable is attached to the at the start of each warm season.
Page 341 MAINTAINING YOUR VEHICLE 339 Refrigerant Recovery And Recycling WARNING! R-134a Air Conditioning Refrigerant is a hydrofluoro- • Use only refrigerants and compressor lubricants carbon (HFC) that is endorsed by the Environmental approved by the manufacturer for your air condi- Protection Agency and is an ozone-saving product. How- tioning system.
Page 342 340 MAINTAINING YOUR VEHICLE The A/C air filter is located in the fresh air inlet on the 2. Pull the console closeout cover rearward to disengage lower right of center console. Perform the following the front retaining tab and remove the cover. procedure to replace the filter: 1.
Page 343 MAINTAINING YOUR VEHICLE 341 3. Remove the two 5.5mm screws (1 and 2) that secure the particulate air filter cover to the HVAC housing. A/C Air Filter 5. Install the A/C air filter with the air filter position indicators pointing in the same direction as removal. 4.
Page 344: Body Lubrication
342 MAINTAINING YOUR VEHICLE be wiped clean to remove dust and grit; after lubricating CAUTION! excess oil and grease should be removed. Particular attention should also be given to hood latching compo- The A/C air filter is identified with an arrow to nents to ensure proper function.
Page 345 MAINTAINING YOUR VEHICLE 343 Operation of the wipers on dry glass for long periods Rear Wiper Blade Removal/Installation may cause deterioration of the wiper blades. Always use 1. Lift the pivot cap on the rear wiper arm upward, this washer fluid when using the wipers to remove salt or dirt will allow the rear wiper blade to be raised off of the from a dry windshield or rear window.
Page 346 344 MAINTAINING YOUR VEHICLE NOTE: The rear wiper arm cannot be raised fully up- ward unless the pivot cap is raised first. 2. Lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder.
Page 347: Adding Washer Fluid
MAINTAINING YOUR VEHICLE 345 5. Lower the wiper blade and snap the pivot cap into Exhaust System place. The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust Adding Washer Fluid system. The windshield washer fluid reservoir is located in the If you notice a change in the sound of the exhaust system;...
Page 348 346 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Exhaust gases can injure or kill. They contain • The catalytic converter requires the use of un- carbon monoxide (CO), which is colorless and leaded fuel only. Leaded gasoline will destroy the odorless. Breathing it can make you unconscious effectiveness of the catalyst as an emissions control and can eventually poison you.
Page 349 MAINTAINING YOUR VEHICLE 347 Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter dam- verter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage.
Page 350: Cooling System
348 MAINTAINING YOUR VEHICLE Cooling System applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh engine coolant (anti- WARNING! freeze). Check the front of the A/C condenser for any •...
Page 351 MAINTAINING YOUR VEHICLE 349 Selection Of Coolant CAUTION! (Continued) Refer to “Fluids, Lubricants, and Genuine Parts” in • Do not use water alone or alcohol-based engine “Maintaining Your Vehicle” for further information. coolant (antifreeze) products. Do not use additional CAUTION! rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and •...
Page 352 350 MAINTAINING YOUR VEHICLE you use the same engine coolant (OAT coolant conform- (antifreeze) solution. The use of lower quality water ing to MS-12106) throughout the life of your vehicle. will reduce the amount of corrosion protection in the engine cooling system. Please review these recommendations for using Organic Additive Technology (OAT) engine coolant (antifreeze) Please note that it is the owner’s responsibility to main-...
Page 353 MAINTAINING YOUR VEHICLE 351 The cap should be inspected and cleaned if there is any Disposal Of Used Engine Coolant accumulation of foreign material on the sealing surfaces. Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check WARNING! with your local authorities to determine the disposal rules for your community.
Page 354 352 MAINTAINING YOUR VEHICLE • Do not overfill the coolant expansion bottle. As long as the engine operating temperature is satisfac- tory, the coolant bottle need only be checked once a • Check the coolant freeze point in the radiator and in month.
Page 355: Brake System
MAINTAINING YOUR VEHICLE 353 • Keep the front of the radiator clean. If your vehicle is WARNING! equipped with air conditioning, keep the front of the condenser clean. Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or •...
Page 356 354 MAINTAINING YOUR VEHICLE when the pads are replaced. However, low fluid level WARNING! may be caused by a leak and a checkup may be needed. • Use only manufacturer’s recommended brake NOTE: If your vehicle is equipped with a manual trans- fluid.
Page 357 MAINTAINING YOUR VEHICLE 355 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or • Do not allow petroleum-based fluid to contaminate moisture, use only new brake fluid or fluid that has the brake fluid. Brake seal components could be been in a tightly closed container.
Page 358: Manual Transmission - If Equipped
356 MAINTAINING YOUR VEHICLE Manual Transmission – If Equipped NOTE: If contaminated with water, the fluid should be changed immediately. Lubricant Selection Automatic Transmission – If Equipped Use only the manufacturers recommended transmission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in Selection Of Lubricant “Maintaining Your Vehicle”...
Page 359 MAINTAINING YOUR VEHICLE 357 leaks. Avoid using transmission sealers as they may CAUTION! adversely affect seals. Using a transmission fluid other than the manufac- CAUTION! turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter Do not use chemical flushes in your transmission as shudder.
Page 360: Appearance Care And Protection From Corrosion
358 MAINTAINING YOUR VEHICLE the transmission fluid level checked. Operating the ve- Appearance Care And Protection From Corrosion hicle with an improper fluid level can cause severe Protection Of Body And Paint From Corrosion transmission damage. Vehicle body care requirements vary according to geo- graphic locations and usage.
Page 361 MAINTAINING YOUR VEHICLE 359 • If insects, tar, or other similar deposits have accumu- What Causes Corrosion? lated on your vehicle, use MOPAR® Super Kleen Bug Corrosion is the result of deterioration or removal of and Tar Remover to remove. paint and protective coatings from your vehicle.
Page 362 360 MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, Special Care de-icer salt, etc., be sure that such materials are well • If you drive on salted or dusty roads or if you drive packaged and sealed. near the ocean, hose off the undercarriage at least once •...
Page 363 MAINTAINING YOUR VEHICLE 361 • For tough stains, apply MOPAR® Total Clean, or a CAUTION! mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. Do not use scouring pads, steel wool, a bristle brush, or metal polishes.
Page 364 362 MAINTAINING YOUR VEHICLE can act as an abrasive and damage the leather upholstery Plastic is not as scratch resistant as glass and therefore and should be removed promptly with a damp cloth. different lens cleaning procedures must be followed. Stubborn soils can be removed easily with a soft cloth To minimize the possibility of scratching the lenses and and MOPAR®...
Page 365 MAINTAINING YOUR VEHICLE 363 When cleaning the rear view mirror, spray cleaner on the Cleaning Plastic Instrument Cluster Lenses towel or rag that you are using. Do not spray cleaner The lenses in front of the instruments in this vehicle are directly on the mirror.
Page 366: Convertible Top Care - If Equipped
364 MAINTAINING YOUR VEHICLE Replace the belts if they appear frayed or worn or if the CAUTION! (Continued) buckles do not work properly. • Remove any standing water from the top and dry Convertible Top Care – If Equipped the surface before opening it. Operating the top, opening a door or lowering a window while the top NOTE: Lubricate the top rails with Berulub FR 43 every is wet may allow water to drip into the vehicles...
Page 367 MAINTAINING YOUR VEHICLE 365 must use an automatic car wash, soft cloth systems are CAUTION! preferred. Never use an abrasive type cleaner or bleaches. CAUTION! Cleaners should not contain silicones, organic sol- vents, petroleum distillates, or plasticizers. Always Avoid high-pressure car washes, as they can damage wait until the top is thoroughly dry before lowering the top material.
Page 368: Fuses
366 MAINTAINING YOUR VEHICLE FUSES Vehicle Mini Cavity Fuse Description Interior Fuses Fuse Number The interior fuse panel is part of the Body Control Right Low Beam Module (BCM) and is located on the driver’s side under the instrument panel. Brown 5 Amp Front and Rear...
Page 369 MAINTAINING YOUR VEHICLE 367 Vehicle Vehicle Mini Mini Cavity Fuse Description Cavity Fuse Description Fuse Fuse Number Number 20 Amp Bi-Directional 5 Amp Stop Light Switch, Yellow Washer Instrument Panel Node 20 Amp Passenger Power Yellow Window 5 Amp Exterior Mirror, GPS, Electric Mir- Left Low Beam, ror, Parking Sensor...
Page 370: Underhood Fuses
368 MAINTAINING YOUR VEHICLE Underhood Fuses The ID number of the electrical component correspond- ing to each fuse can be found on the back of the cover. The Front Distribution Unit is located on the right side of the engine compartment, next to the battery. To access the Maxi Cavity Mini Fuse...
Page 371 MAINTAINING YOUR VEHICLE 369 Maxi Maxi Cavity Mini Fuse Description Cavity Mini Fuse Description Fuse Fuse 30 Amp Radiator Fan - 5 Amp High beam (Shut- Green Low Speed ter) 40 Amp Radiator Fan - 15 Amp Cigar Lighter Orange High Speed Blue 30 Amp...
Page 372: Vehicle Storage
370 MAINTAINING YOUR VEHICLE Maxi Maxi Cavity Mini Fuse Description Cavity Mini Fuse Description Fuse Fuse 7.5 Amp Air Conditioning 10 Amp Transmission Brown 15 Amp Heated Seats – If 15 Amp Rear Defroster, Blue Equipped Blue Heated Mirrors 15 Amp Fuel Pump 5 Amp Lights...
Page 373: Replacement Bulbs
MAINTAINING YOUR VEHICLE 371 • Anytime you store your vehicle, or keep it out of Exterior Bulbs service (i.e., vacation) for two weeks or more, run the Bulb Number air conditioning system at idle for about five minutes Front Low and High HIR2 in the fresh air and high blower setting.
Page 374: Bulb Replacement
372 MAINTAINING YOUR VEHICLE 4. Install the bulb and rotate clockwise to lock in place. Bulb Number Center High Mounted 5. Reinstall the plastic cap. Stop Lamp Front Turn Signal, Parking And Daytime Running License Plate Lamps LED (See Authorized Lamps studio) 1.
Page 375: Front Fog Lamps
MAINTAINING YOUR VEHICLE 373 7. Reinstall the plastic cap. Front Fog Lamps To replace the front fog lights, see your authorized studio. Front/Rear Side Marker Lamps 1. Remove portion of the wheel liner to allow hand access to side marker lamp. 2.
Page 376: Rear Tail, Stop, Backup And Turn Signal Lamps
374 MAINTAINING YOUR VEHICLE Rear Tail, Stop, Backup And Turn Signal Lamps 4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise. 1. Open the liftgate. 5. Remove the backup lamp bulb by pulling straight out. 2.
Page 377: Fluid Capacities
MAINTAINING YOUR VEHICLE 375 FLUID CAPACITIES U.S. Metric Fuel (Approximate) 10.5 Gallons 40 Liters Engine Oil with Filter 1.4L/1.4L Turbo Engine 4 Quarts 3.8 Liters Cooling System 1.4 Liter Engine (MOPAR® 4.6 Quarts 4.4 Liters Antifreeze/Engine Coolant 10 Year/150,000 Mile Formula) — with Manual Transmission 1.4 Liter Engine (MOPAR®...
Page 378: Fluids, Lubricants And Genuine Parts
376 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant - 1.4L/1.4L We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Turbo Engine Formula OAT (Organic Additive Technology). Engine Oil - 1.4L Engine We recommend you use API Certified SAE 5W-30 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
Page 379: Chassis
MAINTAINING YOUR VEHICLE 377 Chassis Component Fluid, Lubricant, or Genuine Part Manual Transmission – If Equipped We recommend you use MOPAR® C635 DDCT/MTX Transmission Fluid Automatic Transmission – If Equipped We recommend you use MOPAR® AW-1 Transmission Fluid Brake Master Cylinder We recommend you use MOPAR®...
Page 381: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS MAINTENANCE SCHEDULE ... . .380 Maintenance Chart ....382...
Page 382 • Check function of all interior and exterior lights tions can cause the change oil message to illuminate as early as 3,500 miles (5,600 km) since last reset. Have your vehicle serviced as soon as possible, within the next 500...
Page 383 MAINTENANCE SCHEDULES 381 Required Maintenance Intervals. At Every Oil Change Interval As Indicated By Oil Change Indicator System: Refer to the maintenance schedules on the following • Inspect engine cooling system protection and page for the required maintenance intervals. hoses. At Every Oil Change Interval As Indicated By Oil •...
Page 384 382 MAINTENANCE SCHEDULES Maintenance Chart Refer to the Maintenance Schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends and boot seals, and re- place if necessary.
Page 385 MAINTENANCE SCHEDULES 383 Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Maintenance Replace engine air filter. Replace cabin air filter. Clean and lube sun roof tracks. Replace spark plugs. ** Flush and replace the engine cool- ant at 10 years or 150,000 miles (240,000 km) whichever comes first.
Page 386 384 MAINTENANCE SCHEDULES ** The spark plug change interval is mileage based only, yearly intervals do not apply. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 387: If You Need Consumer Assistance
DEPARTMENT OF TRANSPORTATION UNIFORM FIAT Customer Center ....387 TIRE QUALITY GRADES ....391 Customer Assistance For The Hearing Or Treadwear.
Page 388: Suggestions For Obtaining Service For Your Vehicle
386 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 389: Fiat Customer Center
• Vehicle delivery date and mileage This is why you should always talk to an authorized FIAT Customer Center studio service manager first. Most matters can be re- solved with this process. P.O. Box 21–8004 •...
Page 390: Service Contract
388 IF YOU NEED CONSUMER ASSISTANCE Canadian residents with hearing difficulties that require The manufacturer will not stand behind any service assistance can use the special needs relay service offered contract that is not the manufacturer’s service contract. It by Bell Canada. For TTY teletypewriter users, dial 711 is not responsible for any service contract other than the and for Voice callers, dial 1 800 855-0511 to connect with manufacturer’s service contract.
Page 391: Warranty Information
See the Warranty Information Booklet, located on the dio, and the manufacturer. DVD, for the terms and provisions of FIAT Group Automobiles warranties applicable to this vehicle and To contact NHTSA, you may either call the Auto Safety market.
Page 392: In Canada
Customer Service Department imme- diagnosing/troubleshooting, problem solving, maintain- diately. Canadian customers who wish to report a safety ing, servicing, and repairing FIAT Group Automobiles defect to the Canadian government should contact Trans- vehicles. A complete working knowledge of the vehicle,...
Page 393: Department Of Transportation Uniform
FIAT Group Automobiles ve- All passenger car tires must conform to Federal safety hicles. Included are starting, operating, emergency and requirements in addition to these grades.
Page 394: Traction Grades
392 IF YOU NEED CONSUMER ASSISTANCE significantly from the norm due to variations in driving Temperature Grades habits, service practices, and differences in road charac- The temperature grades are A (the highest), B, and C, teristics and climate. representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under Traction Grades controlled conditions on a specified indoor laboratory...
Page 395 IF YOU NEED CONSUMER ASSISTANCE 393 WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive load- ing, either separately or in combination, can cause heat buildup and possible tire failure.
Page 397 INDEX...
Page 398 396 INDEX Adding Engine Coolant (Antifreeze) ... .349 Antifreeze (Engine Coolant) ....349 Adding Fuel ......285 Capacities .
Page 399 INDEX 397 Battery ....... . .337 Capacities, Antifreeze (Engine Coolant) ..375 Jump Starting .
Page 400 398 INDEX Cleaning Inspection ......351 Wheels .......360 Points to Remember .
Page 401 INDEX 399 Downshifting ......223 Engine Driving Air Cleaner ......336 Through Flowing, Rising, or Shallow Standing Break-In Recommendations .
Page 402 400 INDEX Exhaust Gas Caution......24 Fluids, Lubricants and Genuine Parts ...376 Exhaust System .
Page 403 INDEX 401 Fuses ........366 Hazard Driving Through Flowing, Rising, or Shallow Gas Cap (Fuel Filler Cap) .
Page 404 402 INDEX Infant Restraint ......56 Key, Sentry (Immobilizer) ....13 Information Center, Vehicle .
Page 405 INDEX 403 Exterior .......81 Loading Vehicle Fog ....... . .145 Tires .
Page 406 404 INDEX Mirrors ....... . .89 Change Interval ......333 Automatic Dimming .
Page 407 INDEX 405 Passing Light ......111 Radio (Sound Systems) .....174 Pets.
Page 408 406 INDEX Safety Checks Outside Vehicle ....81 Adjustment ......100 Safety Defects, Reporting .
Page 409 INDEX 407 Starting ....... .219 Synthetic Engine Oil ..... . .335 Automatic Transmission .
Page 410 408 INDEX Life of Tires ......270 Traction Control ......246 Load Capacity .
Page 411 INDEX 409 Unleaded Gasoline ......280 Wheel and Wheel Trim Care ....360 Untwisting Procedure, Seat Belt .
Page 412 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Page 413 Chrysler Group LLC Printed in U.S.A. 5th Edition 13FF500-126-AE...

This manual is also suitable for:

500c 2013 500 2013 500c

Fiat 500 Owner's Manual

Introduction

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Quick Links

Chapters

Related Manuals for Fiat 500

Summary of Contents for Fiat 500