Important Safety Instructions; Important Safeguards - GBC Titan 1244WF Installation & Operating Manual

GBC 1264WF/1244WF

IMPORTANT SAFETY INSTRUCTIONS

YOUR SAFETY AS WELL AS THE SAFETY OF
OTHERS IS IMPORTANT TO GBC. IN THIS
INSTRUCTION MANUAL AND ON THE PRODUCT,
YOU WILL FIND IMPORTANT SAFETY MESSAGES
REGARDING THE PRODUCT.
MESSAGES CAREFULLY. READ ALL OF THE
INSTRUCTIONS AND
INSTRUCTIONS FOR LATER USE.
THE SAFETY ALERT SYMBOL PRECEDES
EACH SAFETY
INSTRUCTION MANUAL. THE SYMBOL
INDICATES A POTENTIAL PERSONAL
SAFETY HAZARD TO YOU OR OTHERS.
THE FOLLOWING
FOUND UPON THIS PRODUCT.
ADVERTENCIA Attention
Riesgo de choque Risque de
eléctrico Secousseélectrique.
No abra: Ne pas ouvrir.
Adentro no hay Pas de pièces
piezas reparables réparables par
por el usuario. l'utilisateur.
Mantenimiento Entretien
solamente por seulement par
personal calificado personnel qualifié.
THIS SAFETY MESSAGE MEANS THAT YOU
COULD BE SERIOUSLY HURT OR KILLED IF YOU
OPEN THE PRODUCT AND EXPOSE YOURSELF
TO HAZARDOUS VOLTAGE.
ADVERTENCIA
Attention
RODILLOS ROULEAUX
CALIENTES. CHAUDS.
PUNTO DE POINT DE
PINCHAMIENTO. PINCEMENT.
Mantener manos y Tenir mains et
ropa a distancia. vêtements à
l'écart.
THIS SAFETY MESSAGE MEANS THAT YOU
COULD BE BURNED AND YOUR FINGERS COULD
BE TRAPPED AND CRUSHED IN THE HOT
ROLLERS. CLOTHING, JEWELRY AND LONG
HAIR COULD BE CAUGHT IN THE ROLLERS AND
PULL YOU INTO THEM.
ADVERTENCIA
Attention
NAVAJA FILOSA. LAME
COUPANTE.
Mantener manos y
dedos a distancia. Tenir mains et
doigts à l'écart.
THIS SAFETY MESSAGE MEANS THAT YOU
COULD CUT YOURSELF IF YOU ARE NOT
CAREFUL.
WARNING: THIS
SYMBOL PRECEDES
MESSAGE IN
MANUAL. THE SYMBOL INDICATES A
POTENTAL PERSONAL SAFETY HAZARD
TO YOU OR OTHERS.
WARNING: DO
SERVICE OR REPAIR THE 1264/1244 WF
LAMINATOR.
WARNING: DO
LAMINATOR TO
SUPPLY OR ATTEMPT TO OPERATE THE
LAMINATOR UNTIL
COMPLETELY
INSTRUCTIONS.
INSTRUCTIONS
LOCATION FOR FUTURE REFERENCE.
© 2006 General Binding Corporation
READ THESE
SAVE THESE
MESSAGE IN THIS
WARNINGS ARE
Avertissement
Electrical shock
hazard.
Do not open.
No user serviceable
parts inside.
Refer servicing to
qualified service
personnel.
Avertissement
HOT ROLLS.
PINCH POINT.
Keep hands and
clothing away.
Avertissement
SHARP BLADE.
Keep hands and
clothing away.
SAFETY ALERT
EACH SAFETY
THIS INSTRUCTION
NOT ATTEMPT TO
NOT CONNECT THE
AN ELECTRICAL
YOU HAVE
READ THESE
MAINTAIN THESE
IN A CONVENIENT

IMPORTANT SAFEGUARDS

WARNING: TO GUARD AGAINST INJURY
THE FOLLOWING
PRECAUTIONS MUST BE OBSERVED IN
INSTALLATION
LAMINATOR.
General:
Keep hands, long hair, loose clothing, and articles such as
necklaces or ties away from the front of the heat and pull
rollers to avoid entanglement and entrapment.
The heat rollers can reach temperatures over 300˚F (150°C).
Avoid contact with the heat rollers during operation or shortly
after power has been removed from the laminator.
Keep hands and fingers away from the path of the sharp film
cutter blades.
Do not use the laminator for other than its intended purpose.
Avoid moving the Laminator on uneven floor surfaces. Never
tilt the laminator.
Do not defeat or remove electrical and mechanical safety
equipment such as interlocks, shields and guards.
Do not insert objects unsuitable for laminating or expose the
equipment to liquids.
Electrical:
The Laminator should be connected only to a source of power
as indicated in these instructions and on the serial plate located
on the rear of the laminator. Contact an electrician should the
attachment plug provided with the Laminator not match the
receptacles at your location.
WARNING: THE RECEPTACLE MUST BE
LOCATED NEAR THE EQUIPMENT AND
EASILY ACCESSIBLE.
Do not operate the Laminator with a damaged power supply
cord or attachment plug, upon occurrence of a malfunction, or
after the laminator has been damaged. Contact GBC's
Technical Service Department or your dealer/distributor for
assistance.
Service:
Perform only the routine maintenance procedures referred to in
these instructions
WARNING: DO NOT ATTEMPT TO SERVICE
OR REPAIR THE LAMINATOR
Disconnect the plug from the receptacle and contact GBC's
Technical Department or your dealer/distributor when one or
more of the following has occurred.
The power supply cord or attachment plug is damaged.
Liquid has been spilled into the laminator.
The laminator is malfunctioning after being mishandled.
The laminator does not operate as described in these
instructions.
Operation Manual
SAFETY
AND USE OF THE
Page 4