Page 1
Installation Self-Cleaning Radiant Electric Slide-In Range Instructions JSP47, JSP57, JS968 If you have questions, call 1.800.GE.CARES or visit our website at: www.GEAppliances.com Note to Installer--Be sure to leave these Before You Begin instructions with the consumer. Read these instructions carefully and completely.
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS For Your Safety WARNING: To reduce the risk of tipping, the appliance must be secured by properly installing WARNING: For personal the Anti-Tip bracket packed with the safety, remove house fuse or open appliance. circuit breaker before beginning installation.
To obtain Kits: countertop. a, Visit GE Web Site (See page 1 ) b. Call GE Answer Center (See page 1) c. Contact Dealer (Continued on following page)
Page 4
Installation Instructions Pre-lnstallation Checklist cont. Storage Drawer Removal Door removal is not a requirement for installation of the product, but is an added convenience. To remove the door: Pull the drawer out until it stops. Open the oven door as far as it will go. Lift the front of the drawer until the stops clear the guides.
Page 5
Installation Instructions Ii-I Pre-lnstallation Cutout and Required Clearances OVERALLDEPTH Ik_/ 27-t/2" If cabinets are placed less than 30" above the range, see Alternate Construction, section AF, on page 16. NOTE: Product meets UL requirements for 0" clearance to back and side walls. Wall coverings, counters and cabinets...
Installation Instructions Standard Installation I--2-1 STANDARD INSTALLATION Wall ._ 1/4" Min. Flat Flat Area 25" Typically 9/16" Min. 9/16" Min. Flat ---_ ..I" 29-15/16"- 30-1/16" Smooth Cut If the construction of your cabinet cannot Center the 30" wide opening over the provide a 1/4"...
Installation Instructions Electrical Connections ELECTRICAL REQUIREMENTS Use only a 3-conductor or a 4-conductor UL-listed range cord. These cords may be CAUTION: provided with ring terminals on wire and For personal safety, a strain relief device. do not use an extension cord with this appliance.
Installation Instructions Electrical Connections cont. POWER CORD AND STRAIN For power cord installations only (see RELIEF INSTALLATION the next step if using conduit), assemble the strain relief in the hole. Insert the power cord through the strain relief and Remove the wire cover tighten.
Page 9
Installation Instructions Electrical Connections cont. 3-WIRE POWER CORD I-_ 4-WIRE POWER CORD INSTALLATION INSTALLATION WARNING: WARNING: The neutral or The neutral wire of ground wire of the power cord must the supply circuit must be connected be connected to the neutral terminal to the neutral terminal located in the located...
Page 10
Installation Instructions Electrical Connections cont. 3-WIRE CONDUIT INSTALLATION 4-WIRE CONDUIT INSTALLATION Loosen the 3 lower terminal screws Loosen the three lower terminal screws from the terminal block. Insert the center from the terminal block. Remove the bare wire (white/neutral) tip through the ground screw and ground plate and retain them.
Installation Instructions Installing the Range r-_ REPLACE THE WIRE COVER [_-_ INSTALLING THE BRACKET IN WOOD OR CONCRETE Replace the wire cover INSTALLATION_WOOD (on the back of the CONSTRUCTIONS range) by replacing 2 screws removed Locate the centers of the 4 holes earlier.
Page 12
Installation Instructions Installing The Range cont. SLIDE RANGE INTO OPENING SLIDE RANGE INTO OPENING (cont.) Position the range in front of the ® cabinet opening. Plug the range cord into the receptacle. Locate the cord in the back of the range Make sure that the glass which in a manner that it will not touch or be overhangs...
Installation Instructions Installing The Range cont. REPLACING THE OVEN DOOR REPLACING THE STORAGE DRAWER NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. P,acethe on the guides. Do not lift the door by the handle.
Installation Instructions Final Checklist Check to make sure the circuit breaker is closed (Reset) or the circuit fuses are replaced. Be sure power is in service to the building. Check to be sure that all packing materials and tape on metal panel (if applicable) under control knobs and drawer have been removed.
Installation Instructions Alternate Construction IA--_ OPTIONAL MAINTOP FILLER If you use the filler kit, place the metal filler piece supplied with the range to the back OR BACKGUARDKIT of the range as shown in the figure below. Start the 2 screws into the upper holes at the If counter opening extends to the wall, it will outside rear of the range above the louvers...
Page 16
Installation Instructions Alternate Construction cont. FA-_ COUNTERTOPS HIGHER [A-'_ ISLAND INSTALLATION THAN 36-1/2" Attach the Anti-Tip bracket per instructions If countertop height is between 36-1/2" in section D, making sure that the rear of the bracket is 25" from the front of the and 38_' a lower trim kit (JXS56XX) recommended.