Electronic Oven Controls; Oven Light; Troubleshooting - Maytag W10392921B User Instructions

The oven light is a standard 40-watt appliance bulb. Before
replacing, make sure the oven and cooktop are cool and the
control knobs are in the off position.
To Replace:
1. Unplug range or disconnect power.
2. Turn the glass bulb cover in the back of the oven
counterclockwise to remove.
3. Turn bulb counterclockwise to remove from socket.
4. Replace bulb, then bulb cover by turning clockwise.
5. Plug in range or reconnect power.
TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
to possibly avoid the cost of a service call.
www.maytag.com
Cooktop will not operate
Plug into a grounded outlet.
Press any key on the control to display the Time of Day. See the
"Electronic Oven Controls" section for more information.
Replace the fuse or reset the circuit breaker. If the problem
continues, call an electrician.
The electrical outlet in the home may be miswired. Contact a
qualified electrician to verify the electrical supply.
Push in knob before turning to a setting.
Operation
PROBLEM POSSIBLE CAUSES SOLUTIONS
Nothing will operate Power supply cord is unplugged.
ENERGY SAVE is active, and the
display is blank.
Household fuse is blown, or a
circuit breaker is tripped.
The control displays an F9 or F9
E0 error code.
The control knob is not set
correctly.
On ceramic glass models, the See the control lock keypad feature in the "Feature Guide."
oven control lockout is set.
Excessive heat around Cookware is not the proper size. Use cookware about the same size as the surface cooking
cookware on cooktop area, element or surface burner. Cookware should not extend
more than 1/2"(1.3 cm) outside the cooking area.
Cooktop cooking results not Control knob set to incorrect heat See "Cooktop Use" section.
what expected level
Oven will not operate
Range is not level.
Delay start is set.
Control lock is on.
Level the range. See the Installation Instructions.
See "Timed Cooking" section.
Press and hold START for 3 seconds to unlock.
Control is in Demo Mode. Press and hold DELAY START for 10 seconds.
Electronic oven control set See "Electronic Oven Controls" section.
incorrectly
Oven temperature too high or Oven temperature needs See "Oven Temperature Control" in the "Electronic Oven
too low adjustment. Controls" section.
Oven indicator lights flash Power to range is turned on or See "Control Display" in the "Electronic Oven Controls"
restored, section. If the indicator lights keep flashing, call for service. See
cover for contact information.
Display shows messages Power failure (display shows Clear the display. On some models, reset the clock, if needed.
flashing time) See "Clock" keypad feature in the "Feature Guide" section.
Error code (display shows letter
followed by number)
Depending on your model, press CANCEL to clear the display.
See "Control Display" in the "Electronic Oven Controls"
section. If it reappears, call for service. See cover for contact
information.
Clean cycle did not work on all
spills
Start needs to be pressed so a
cycle can begin (display shows
"PUSH" or "PSH").
Several cooking cycles between
Clean cycles or spills on oven
walls and doors.
See the "Start" keypad feature in the "Feature Guide" section.
Run additional Clean cycles. Use the AquaLift
TM
Technology
Cleaning Kit. Use affresh
TM
Kitchen and Appliance Cleaner or
affresh
TM
Cooktop Cleaner. See the "Accessories" section for
more information.
Mineral deposits are left on the
oven bottom after the Clean
cycle
Tap water was used in the Clean
cycle.
Use distilled or filtered water in the Clean cycle.
To remove deposits, use a cloth soaked with vinegar. Then use
a cloth dampened with water to thoroughly remove any vinegar
residue.
15