Control Elements; Mono And Stereo Channels - Behringer Europower PMP6000 User Manual

8
EUROPOWER PMP6000/PMP4000/PMP1000 User Manual
(66)
(67) (68)
EUROPOWER PMP6000 REAR PANEL

2. Control Elements

A detailed description of all functions of your power mixer can be found in the
following chapters. Please also refer to the enclosed sheet with the numbered
illustrations to get a good overview of the control layout.

2.1 Mono and stereo channels

(1) Use the GAIN control to adjust the input gain. Be sure to set this control
fully counter-clockwise before you connect or disconnect a signal source to
an input. GAIN controls both the microphone and the LINE input. The black
scale shows the microphone gain (+10 to +60 dB on channels with XENYX
MIC PREAMPS and 0 to +40 dB on conventional microphone inputs;
PMP1000 only, channels 5/6 and 7/8).
The "LINE" scale indicates the sensitivity of the LINE input, ranging from
+10 to -40 dBu.
PMP1000: The mono/stereo combination channels 5/6 and 7/8 have a
sensitivity of +20 to -20 dBu.
(2) The LEVEL SET LED illuminates when an optimum operating level has
been adjusted.
(3) The mono channels are equipped with a high-slope LOW CUT filter
eliminating unwanted low-frequency signals like rumble noise.
(4) PMP4000/PMP6000 (stereo channels): Press the A/B button to switch
from 1/4" jacks to RCA connectors, and vice versa. Position "A" = 1/4" jacks;
position "B" = RCA connectors.
(5) The HIGH control in the EQ section governs the high frequency range of the
respective channel.
(6) Use the MID control to boost or cut the midrange frequencies.
(7) PMP6000: The PMP6000 has an additional semi-parametric filter for the
midrange frequencies in the mono channels (tunable from 100 Hz to 8 kHz).
Adjust the boost/cut with the MID control, and the frequency with the
FREQ control.
The stereo channels contain a stereo EQ section. The cut-off frequencies
of the high and low bands are 12 kHz and 80 Hz respectively, while the
center frequencies of the high-mid and low-mid bands are 3 kHz and
400 Hz respectively.
(8) The LOW control allows you to boost/cut the low frequency range.
(9) With the MON(ITOR) control you can adjust the volume of each channel in
the monitor mix.
(10) The PMP4000 and PMP6000 feature a second MON control (MON 2) for the
volume of the second monitor bus.
(11) The FX control determines the signal level sent from each channel to the
built-in effects processor; this signal is also present at the FX SEND jack
(see (64) ).
(69)
(12) The PMP6000 has two FX controls (FX 1 and FX 2), so that you can use two
effects simultaneously. Accordingly, the PMP6000 also has two effect aux
buses, which have one output jack in common (see (46) and (64) ).
◊
Please note that the effects processor signal will be inaudible,
as long as the FX TO MON/MAIN controls (40) , (41) , (42) are set fully
counter-clockwise.
(13) The PAN(ORAMA) control determines the position of the channel signal in
the stereo main mix.
(14) The BAL(ANCE) control for the stereo channels corresponds to the PAN
control for the mono channels. It determines the relative volume of the left
and right input signals before they are routed to the stereo main output.
(15) PMP4000/PMP6000: When you press the PFL button (Pre Fader Listening)
the left LED (34) shows the pre-fader input gain of the channel. Adjust the
optimum input gain (0 dB) with the GAIN control (1) . When PFL is on,
the corres ponding LED illuminates.
If the LEVEL SET LED (2) is illuminated constantly, the signal is within the
optimum operating level range. However, if the CLIP LED indicates that the
input gain is too high, you should reduce the level slightly with the GAIN
control. The CLIP LED should never be illuminated all the time, only with
signal peaks.
(16) The MUTE switch mutes the channel in the main mix. The pre-fader signals
(monitor buses) remain operative. When MUTE is pressed, the corresponding
control LED illuminates.
(17) The channel fader controls the channel signal level in the main mix.
2.1.1 Input section
(18) Each mono input channel is equipped with a balanced microphone input
(XLR connector) which provides +48 V phantom power for condenser
microphones at the touch of a button (see rear panel).
PMP1000: The two stereo channels 5/6 and 7/8 have an additional balanced
XLR microphone input with +48 V phantom power.
◊
Be sure to switch off your audio system before you activate the
phantom power supply to protect your monitor speakers from
switch-on thumps.
(19) Each mono input features one LINE IN connector (1/4" jack), which can be used
with either balanced or unbalanced signals.
◊
Please remember to use either the microphone or the line input on a
specific channel. Never use both at the same time!
◊
When you connect a mono line signal to a stereo channel, always use
the left input. The mono signal will then be reproduced by both
sides equally.
(70)
(72) (71)