How To Program The Features; To Program Features/Transmitters; How To Program Transmitters To The System - Omega K9-Mundial Owner's Manual & Installation Instructions

9. System Activation Cycle Duration: (•30 / 60 Seconds)
- Configures the system's activation duration cycle to be either 30 seconds or
60 seconds. If programming, press the transmitter's large button for the 30
Second setting or press the small button for the 60 second setting.
10. Double Unlock Pulse: (On / •Off)
- Configures system to change the single unlock output pulse into a double
unlock pulse. Some newer vehicles require a double pulse to unlock the
doors, when needed this feature saves the expense of optional parts.
11. Open Door Bypass Alert: (On / •Off)
- Configures the system to chirp the siren 3 times upon arming, instead of 1
time, to warn the user if a door is still open.
12. Auxiliary Channel Disarms System Or Engages Start Mode: (•Disarms /
Start Mode)
- This unique feature changes certain aspects of the system's Auxiliary
Channel's operation so that it is more compatible with optional remote starter
units. When this feature is utilized, instead of disarming the system when the
Auxiliary Channel is activated, the system does not disarm. Additionally,
certain of the system's sensory zones are bypassed to prevent false activation
How to Program Features
The 16 programmable features, explained in the previous pages, are very easily
programmed by a procedure using the ignition key, Valet/Override Switch, and
transmitter. To access Features Programming Mode:
Step 1: Turn the vehicle's ignition "On" then "Off".
Step 2: Within 10 seconds of turning the ignition "Off", press the Valet/Override
Switch 5 times. The system will sound a long, then short siren confirm-
ing entry to Features Programming Mode.
Step 3: Within 10 seconds of entering Features Programming Mode, press the
Valet/Override Switch the number of times equal to the number of the
feature to be programmed. The system will repeat the feature number
with same number of chirps.
Step 4: After the system acknowledges the feature to be programmed, press
either the large transmitter button to turn the feature on (the system's
response will be 1 chirp), or the small button to turn the feature off (the
system's response will be 2 chirps).
Page 17
Page 19
due to the remote starting operation. When this feature is set for the Start
Mode, and the Auxiliary Channel is activated, the system will bypass the
current sensing and sensor zones if the system is armed. This allow a remote
start module to start the vehicle without activating the system. The door and
trunk zones remain active, and if violated will trigger the system and turn the
vehicle's engine off. If programming, press the small button for Start Mode
or the the large button for Disarm.
13. Transmitter Activated Anti-Carjacking: (On / •Off)
- This feature's operation is explained on pages 13-14.
14. Door Activated Anti-Carjacking: (On / •Off)
- This feature's operation is explained on pages 13-14.
15. Ignition Activated Anti-Carjacking: (On / •Off)
- This feature's operation is explained on pages 13-14.
16. Chirp Confirmation: (•On / Off)
- This feature allows the arm and disarm confirmation chirps to be turned off.
When this feature is turned off, exceptions will be chirps during programming
and the single chirp produced when the system arms by Last Door Arming
and Automatic Rearming.
To program more features, simply repeat Steps 3 and 4. If 10 seconds expire
without any programming activity the system will automatically exit Feature Pro-
gramming Mode. Turning on the ignition switch will also exit the system from
Feature Programming Mode; in either case the system signals the exit with 1 long
siren chirp.

How to Program Transmitters to the System

Whenever a transmitter, new or existing, is programmed to the system, all exist-
ing codes are erased for security. So all of the transmitters which are to operate
the system, up to four, must be programmed at the same time.
Step 1: Turn "On" the vehicle's ignition.
Step 2: Within 10 seconds press the Valet/Override Switch 5 times. The system
responds with 1 long siren chirp to confirm Transmitter Programming Mode.
Step 3: Within 10 seconds, press the large button on each transmitter to be pro-
grammed. The response to each transmitter button press is 1 chirp.
If 17 seconds expire without any programming activity the system will automati-
cally exit Transmitter Programming Mode. Turning off the ignition switch will also
Page 18
Page 20