Related Manuals for Intel IB935
Summary of Contents for Intel IB935
- Page 1 IB935 ( I B 9 3 5 , I B 9 3 5 R F ) ® Socket LGA775 Pentium ® Intel Q35 Chipset PICMG 1.3 SHB Express CPU Card USER’S MANUAL Version 1.0...
- Page 2 Award is a registered trademark of Award Software International, Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Pentium 4 are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Winbond is a registered trademark of Winbond Electronics Corporation.
-
Page 3: Table Of Contents
BIOS Setup ............23 Drivers Installation ........45 Intel Chipset Software Intallation Utility ......46 Intel Graphics Driver Installation ........48 Realtek HD Code Audio Driver Installation ..... 49 Intel PRO LAN Drivers Installation ........50 IDE Controller Drivers Installation ........52 Appendix ............ - Page 4 The IB935 CPU Card IB935 User’s Manual...
-
Page 5: Introduction
INTRODUCTION Introduction Product Description The IB935 PICMG1.3 SHB board incorporates the Intel® Q35 Express Chipset, consisting of the Intel® Q35 Graphic Memory Controller Hub (GMCH) and Intel® I/O Controller Hub 9 (ICH9), is an optimized integrated graphics solution with a 800/1066/1333 MHz front-side bus. -
Page 6: Checklist
Checklist ® Your IB935 Pentium 4 CPU card package should include the items listed below: • The IB935 CPU card • This User’s manual • 1 Floppy cable • 1 IDE cable • 1 USB cable with bracket (USB2K-4) • 1 Y-Cable supporting a PS/2 Keyboard and a PS/2 Mouse •... -
Page 7: Specifications
Product Name IB935 PICMG 1.3 SHB Express full size CPU card Form Factor CPU Support Socket LGA775, Supports the Intel Core 2 Duo and Intel Core2 Quad processors, and Intel Celeron 400 (Conroe-L) Sequence processor. CPU Voltage 0.5V~1.6V (VRD 11.0) System Speed Up to 3.8GHz+... -
Page 8: Board Dimensions
INTRODUCTION Board Dimensions IB935 User’s Manual... -
Page 9: Installations
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the IB935 in order to set up a workable system. The topics covered are: Installing the CPU ................ 6 Installing the Memory ..............7 Setting the Jumpers ..............8 Connectors on IB935 .............. -
Page 10: Installing The Cpu
INSTALLATIONS Installing the CPU The IB935 board supports an LGA 775 processor socket for Intel Core 2 Duo and Intel Core2 Quad processors, and Intel Celeron 400(Conroe-L) Sequence processor. The LGA 775 processor socket comes with a lever to secure the processor. -
Page 11: Installing The Memory
INSTALLATIONS Installing the Memory The IB935 board supports two DDR2 memory sockets for a maximum total memory of 4GB in DDR2 memory type. It supports DDR2 667/800. Basically, the system memory interface has the following features: Supports two 64-bit wide DDR data channels Available bandwidth up to 6.4GB/s (DDR2 800) for single-channel... -
Page 12: Setting The Jumpers
INSTALLATIONS Setting the Jumpers Jumpers are used on IB935 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on IB935 and their respective functions. -
Page 13: Jumper Locations On Ib935
INSTALLATIONS Jumper Locations on IB935 Jumpers on IB935 ................Page JP1, JP2, JP3: RS232/422/485 (COM2) Selection ......10 JP4: Configure and Recovery (Factory use only) ........ 10 JP5: Power ON Setting ................ 10 JP7: ICH9 PCI-E port 1-4 Configuration Settings ......11 JP11: Clear CMOS Contents ............... -
Page 14: Jp1, Jp2, Jp3: Rs232/422/485 (Com2) Selection
Function Pin 1-2 Normal (default) Short/Closed Pin 2-3 Short/Closed Configure Open Recovery JP5: Power ON Setting JP17 Setting Function Pin 1-2 Power on by system Short/Closed button Pin 2-3 Power on by power Short/Closed supply AC on IB935 User’s Manual... -
Page 15: Jp7: Ich9 Pci-E Port 1-4 Configuration Settings
JP11: Clear CMOS Contents Use JP11 to clear the CMOS contents. Note that the ATX-power connector should be disconnected from the board before clearing CMOS. JP11 Setting Function Pin 1-2 Normal Short/Closed Pin 2-3 Clear CMOS Short/Closed IB935 User’s Manual... -
Page 16: Connectors On Ib935
INSTALLATIONS Connectors on IB935 The connectors on IB935 allow you to connect external devices such as keyboard, mouse, hard disk drives, printers… etc. The following table lists the connectors on IB935 and their respective functions. Connector Locations on IB935 ............13 ATX1: ATX 12V Power Connector ........... -
Page 17: Connector Locations On Ib935
INSTALLATIONS Connector Locations on IB935 ATX1: ATX 12V Power Connector DIMM1: Channel A DDR2 Socket DIMM2: Channel B DDR2 Socket CPU_FAN1: CPU Fan Power Connector SYS_FAN1, SYS_FAN2: System Fan Power CN1, CN2, CN3, CN4: SATA HDD Connector IDE1: Primary IDE Connectors... -
Page 18: Atx1: Atx 12V Power Connector
Pin # Signal Name Ground +12V Rotation detection Control SYS_FAN1, SYS_FAN2: SYSTEM Fan Power Connector Pin # Signal Name Ground +12V Rotation detection CN1, CN2, CN3, CN4: SATA HDD Connector Pin # Signal Name Ground Ground Ground IB935 User’s Manual... -
Page 19: Ide1: Primary Ide Connector
Drive select 1 Ground Drive select 0 Ground Motor enable 1 Ground Direction Ground Step Ground Write data Ground Write gate Ground Track 00 Ground Write protect FDD1 Ground Read data Ground Side 1 select Ground Diskette change IB935 User’s Manual... -
Page 20: Vga1: Vga Crt Connector
PD2, parallel data 2 Select PD3, parallel data 3 Ground PD4, parallel data 4 Ground PD5, parallel data 5 Ground PD6, parallel data 6 Ground PD7, parallel data 7 Ground ACK, acknowledge Ground Busy Ground Paper empty Ground Select IB935 User’s Manual... -
Page 21: J3: Digital I/O Connector (4 In, 4 Out)
Signal Name Ground Out3 Out1 Out2 Out0 J4: IrDA Connector Pin # Signal Name No connect Ir RX Ground Ir TX J5: CD-In Audio Connector Pin # Signal Name CD Audio R Ground Ground CD Audio L IB935 User’s Manual... -
Page 22: J6: Com2 Serial Port
J7 is a 10-pin header support RS232 COM ports. Signal Signal Name Name J8: System Function Connector J8 provides connectors for system indicators that provide light indication of the computer activities and switches to change the computer status. IB935 User’s Manual... - Page 23 Reset Switch: Pins 9 and 19 The reset switch allows the user to reset the system without turning the main power switch off and then on again. Orientation is not required when making a connection to this header. IB935 User’s Manual...
-
Page 24: J9: Ps/2 Keyboard And Mouse Connector
The following table shows the pin out assignments of this connector. Wake On LAN will function properly only with an ATX power supply with 5VSB that has 1A. Pin # Signal Name +5VSB Ground LAN Wakeup IB935 User’s Manual... -
Page 25: J13: Usb Connector
The following table shows the pin outs of the USB pin header. Signal Name Signal Name Ground USB2- USB3+ USB2+ USB3- Ground J15, J17: Gigabit LAN RJ45 Connector J15, J17 are Gigabit LAN RJ45 connectors. J16: SPI Debug Tools Port (Factory use only) IB935 User’s Manual... - Page 26 INSTALLATIONS This page is intentionally left blank. IB935 User’s Manual...
-
Page 27: Bios Setup
PNP/PCI Configurations ..............41 PC Health Status .................. 42 Frequency/Voltage Control ..............43 Load Fail-Safe Defaults ............... 44 Load Optimized Defaults ..............44 Set Supervisor Password ..............44 Save & Exit Setup ................44 Exit Without Saving ................44 IB935 User’s Manual... -
Page 28: Bios Introduction
BIOS Introduction The Award BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial ports and parallel ports. It also adds virus and password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system. - Page 29 These defaults have been carefully chosen by both Award and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could cause the system to become unstable and crash in some cases. IB935 User’s Manual...
-
Page 30: Standard Cmos Setup
Sun to Sat Month : 1 to 12 Date : 1 to 31 Year : 1999 to 2099 To set the date, highlight the “Date” field and use the PageUp/ PageDown or +/- keys to set the current time. IB935 User’s Manual... - Page 31 These fields identify the types of floppy disk drive A or drive B that has been installed in the computer. The available specifications are: 360KB 1.2MB 720KB 1.44MB 2.88MB 5.25 in. 5.25 in. 3.5 in. 3.5 in. 3.5 in. IB935 User’s Manual...
- Page 32 The system boot will not be halted for a disk error; it will stop for all other errors. All, But Disk/Key The system boot will not be halted for a key- board or disk error; it will stop for all others. IB935 User’s Manual...
-
Page 33: Advanced Bios Features
CPU. By default, these items are enabled. Quick Power On Self Test When enabled, this field speeds up the Power On Self Test (POST) after the system is turned on. If it is set to Enabled, BIOS will skip some items. IB935 User’s Manual... - Page 34 Settings are from 6 to 30 characters per second. Typematic Delay (Msec) When the typematic rate is enabled, this item allows you to set the time interval for displaying the first and second characters. By default, this item is set to 250msec. IB935 User’s Manual...
- Page 35 If you set this feature to Disabled, the BIOS will not report the missing floppy drive to Win95/98. Small Logo (EPA) Show The EPA logo appears at the right side of the monitor screen when the system is boot up. The default setting is Disabled. IB935 User’s Manual...
-
Page 36: Advanced Chipset Features
SDRAM is written to, read from or refreshed. Reducing the delay improves the performance of the SDRAM. DRAM RAS# Precharge This option sets the number of cycles required for the RAS to accumulate its charge before the SDRAM refreshes. IB935 User’s Manual... - Page 37 LVDS+TV or LVDS or TV-out setting, install the IBP190 module. SDVO LVDS Protocol: 1Ch 18bit SDVO Panel Number: 852 x 480 Boot Display: Auto Panel Scaling: Auto Panel Number: 1024 x 768 18bit SC Onboard Lan Boot ROM: Enabled Onboard IT8211F IDE ROM: Enabled IB935 User’s Manual...
-
Page 38: Integrated Peripherals
Normal RxD , TxD Active Hi, Lo IR Transmission Delay Enabled UR2 Duplex Mode Half Use IR Pins IR-Rx2Tx2 Onboard Parallel Port 378/IRQ7 Parallel Port Mode EPP Mode Select EPP1.7 ECP Mode Use DMA PWRON After PWR-Fail IB935 User’s Manual... - Page 39 Select [AHCI] for Advanced Host Controller Interface (AHCI) feature, with improved SATA performance with native command queuing & native hot plug. Select [RAID] to use SATA as RAID function. RAID function is supported on the board if it uses ICH9R, but this is optional. IB935 User’s Manual...
- Page 40 The default values for these ports are: Serial Port 1 3F8/IRQ4 Serial Port 2 2F8/IRQ3 Parallel Port 378H/IRQ7 UART Mode Select This field determines the UART 2 mode in your computer. The default value is Normal. IB935 User’s Manual...
- Page 41 The options for this field are Enabled and Disabled. By default, this field is set to Disabled. USB Storage Function The options for this field are Enabled and Disabled. By default, this field is set to Disabled. IB935 User’s Manual...
-
Page 42: Power Management Setup
Min. Power Saving Minimum power management Max. Power Saving Maximum power management. User Define Each of the ranges is from 1 min. to 1hr. Except for HDD Power Down which ranges from 1 min. to 15 min. IB935 User’s Manual... - Page 43 When the system enters Doze mode, the CPU clock runs only part of the time. You may select the percent of time that the clock runs. Wake up by PCI Card By default, this field is disabled. IB935 User’s Manual...
- Page 44 When an I/O device wants to gain the attention of the operating system, it signals this by causing an IRQ to occur. When the operating system is ready to respond to the request, it interrupts itself and performs the service. IB935 User’s Manual...
-
Page 45: Init Display First
MPEG ISA/VESA VGA card. When this field is disabled, a PCI/VGA cannot work with an MPEG ISA/VESA card. Maximum Payload Size The default setting of the PCI Express Maximum Payload Size is 128. IB935 User’s Manual... -
Page 46: Pc Health Status
PC health status. Smart Fan Temperature This field enables or disables the smart fan feature. At a certain temperature, the fan starts turning. Once the temperature drops to a certain level, it stops turning again. IB935 User’s Manual... -
Page 47: Spread Spectrum
Auto Detect PCI Clk This field enables or disables the auto detection of the PCI clock. Spread Spectrum This field sets the value of the spread spectrum. The default setting is Disabled. This field is for CE testing use only IB935 User’s Manual... -
Page 48: Load Fail-Safe Defaults
Select this option to exit the Setup utility without saving the changes you have made in this session. Typing “Y” will quit the Setup utility without saving the modifications. Typing “N” will return you to Setup utility. IB935 User’s Manual... -
Page 49: Drivers Installation
IDE Controller Driver Installation……………………………..52 IMPORTANT NOTE: 1. After installing your Windows operating system(Windows 98SE/ME/2000/XP), you must install first the Intel Chipset Software Installation Utility before proceeding with the drivers installation. 2. How to create an AHCI driver disk, when your board supports the RAID/AHC function: 1. -
Page 50: Intel Chipset Software Intallation Utility
Windows 98SE/ME/2000/XP. (Before installed Intel Chipset Software Installation Utility,Please update your system to Windows 2000 SP4 or Windows XP SP1A) 1. Insert the CD that comes with the board. Click Intel Chipsets and then Intel(R) Bearlake Chipset Family Drivers. 2. Click Intel(R) Chipset Software Installation Utility. - Page 51 5. On the Readme Information screen, click Next to continue the installation. 6. When the Setup Progress screen appears, click Next to continue. 7. The Setup process is now complete. Click Finish then restart the computer and for changes to take effect. IB935 User’s Manual...
-
Page 52: Intel Graphics Driver Installation
To install the Graphics drivers, follow the steps below to proceed with the installation. 1. Insert the DVD that comes with the board. Click Intel Chipsets and then Intel(R) Bearlake Chipset Family Drivers. 2. Click Intel(R) Bearlake Chipset Family Graphics Driver. -
Page 53: Realtek Hd Code Audio Driver Installation
Follow the steps below to install the Realtek High Definition Codec Audio Driver. 1. Insert the DVD that comes with the board. Click Intel Chipsets and then Intel(R) Bearlake Chipset Family Drivers. 2. Click Realtek High Definition Codec Audio Driver. -
Page 54: Intel Pro Lan Drivers Installation
Follow the steps below to start installing the Intel 82566DM or Intel 82574L drivers. 1. Insert the DVD that comes with the board. Click Intel Chipsets and then Intel(R) Bearlake Chipset Family Drivers. 2. Click Intel(R) PRO LAN Network Drivers. - Page 55 DRIVERS INSTALLATION Follow the steps below to use the wake up function by Intel 82566DM or Intel 82574L. 1. The BIOS Setup item “Wake-Up by PCI card” has to be set as [Enabled] . 2. Go to the Device Manager under Windows and select Network adapters.
-
Page 56: Ide Controller Drivers Installation
1. Insert the CD that comes with the motherboard. Click ITE8211 Chip and then IDE Controller Drivers . When the Welcome screen appears, click Next to continue. 2. Select Type as ‘Typical’ and click Next to continue. Restart when promoted and finish the installation process. IB935 User’s Manual... -
Page 57: Appendix
Parallel Port #1(LPT1) 360 - 36F Network Ports 3B0 - 3BF Monochrome & Printer adapter 3C0 - 3CF EGA adapter 3D0 - 3DF CGA adapter 3F0h - 3F7h Floppy Disk Controller 3F8h - 3FFh Serial Port #1(COM1) IB935 User’s Manual... -
Page 58: Interrupt Request Lines (Irq)
Serial Port #2 IRQ4 Serial Port #1 IRQ5 Reserved IRQ6 Floppy Disk Controller IRQ7 Parallel Port #1 IRQ8 Real Time Clock IRQ9 Reserved IRQ10 Reserved IRQ11 Reserved IRQ12 PS/2 Mouse IRQ13 80287 IRQ14 Primary IDE IRQ15 Secondary IDE IB935 User’s Manual... -
Page 59: Watchdog Timer Configuration
; OUT : None ;[]================================================ Enable_And_Set_Watchdog Proc Near push ;save time interval call Unlock_Chip mov cl, 2Bh call Read_Reg and al, NOT 10h call Write_Reg ;set GP24 as WDTO mov cl, 07h mov al, 08h call Write_Reg ;switch to LD8 IB935 User’s Manual... - Page 60 07h mov al, 08h call Write_Reg ;switch to LD8 xor al, al mov cl, 0F6h call Write_Reg ;clear watchdog timer xor al, al mov cl, 30h call Write_Reg ;watchdog disabled call Lock_Chip Disable_Watchdog Endp ;[]=============================================== IB935 User’s Manual...
- Page 61 ; IN : CL - register index AL - Value to write ; OUT : None ;[]================================================ Write_Reg Proc Near push mov dx, 4Eh mov al,cl out dx,al pop ax inc dx out dx,al Write_Reg Endp ;[]================================================ IB935 User’s Manual...
- Page 62 ; Name : Read_Reg ; IN : CL - register index ; OUT : AL - Value to read ;[]================================================= Read_Reg Proc Near Mov al, cl mov dx, 4Eh out dx, al inc dx in al, dx Read_Reg Endp ;[]================================================ IB935 User’s Manual...
-
Page 63: Digital I/O Sample Code
//===================================================================== #define W627HF_INDEX_PORT (W627_IOBASE+0) #define W627HF_DATA_PORT (W627_IOBASE+1) //===================================================================== #define W627HF_REG_LD 0x07 //===================================================================== #define W627HF_UNLOCK 0x87 #define W627HF_LOCK 0xAA //===================================================================== void Set_W627HF_LD( unsigned char); void Set_W627HF_Reg( unsigned char, unsigned char); unsigned char Get_W627HF_Reg( unsigned char); //===================================================================== #endif //__W627HF_H IB935 User’s Manual... - Page 64 Set_W627HF_Reg( unsigned char REG, unsigned char DATA) Unlock_W627HF(); outportb(W627HF_INDEX_PORT, REG); outportb(W627HF_DATA_PORT, DATA); Lock_W627HF(); //===================================================================== unsigned char Get_W627HF_Reg( unsigned char REG) unsigned char Result; Unlock_W627HF(); outportb(W627HF_INDEX_PORT, REG); Result = inportb(W627HF_DATA_PORT); Lock_W627HF(); return Result; //===================================================================== File of the Main.cpp IB935 User’s Manual...
- Page 65 Set_W627HF_Reg(0xF1, ((ucDO & 0x0F) << 4)); ucBuf = Get_W627HF_Reg(0xF1) & 0x0F; if (ucBuf != ucDI) ucDI = ucBuf; printf("Digital I/O Input Changed. Current Data is 0x%X\n",ucDI); if (kbhit()) getch(); break; delay(500); return 0; //===================================================================== void ClrKbBuf(void) while(kbhit()) getch(); //--------------------------------------------------------------------------- IB935 User’s Manual...
- Page 66 APPENDIX This page is intentionally left blank. IB935 User’s Manual...