Related Manuals for Genie GPS-IC Series
Summary of Contents for Genie GPS-IC Series
- Page 2 Check your ceiling where the power You need a 110-120 Volt power supply head of your new unit will be mounted. available. If you plan to plug the unit into a standard electrical outlet, is one available? Plan how you will be mounting the power head.
-
Page 3: Sectional Door Installation
TYPICAL SECTIONAL DOOR iNSTALLATiON ADDED SUPPORT HEADER BRACKET BRACKET MOUNTING BOARD BRACES 36" POWER CORD 120V GROUNDED OUTLET EXTENSION SPRING TORSION SPRING SAFE-T=BEAM®... -
Page 4: Important Installation Instructions
OVERVIEW OF IMPORTANT POTENTIAL HAZARDS INSTALLATION INSTRUCTIONS Garage doorsarelarge,heavyobjectsthatmovewiththe helpof springs underhightensionandelectricmotors. S incemoving objects, s pringsunder tension, a ndelectricmotorscan causeinjuries, y oursafetyandthe safetyof othersdepend on youreading the information inthismanual.Ifyou have questions or do not understand the information presented, c all yournearest servicerepresentative Toreducethe risk of In thissectionandthosethatfollow,the wordsDanger, W arning,and... - Page 5 Immmm i!_L _ _ ,, . :i : i_:L:,_ I "., !i¸¸ :Lui remotes vary by model FASTENERS - Shown full size. See Parts List for description. 1/4"-20 x 3/4" Bolt, #10-24 x 1/2" Self-Drilling Screw Insulated Staple --'m Pan Head Screw #6 x 1-1/4" Bolt, 5/16"-18 x 1/2"...
- Page 11 Fasten rail to power head. • Align mounting holes of sprocket saddle, rail and power head frame. • Insert the two (2) 5/16" x 1/2" hex head screws[112], then two (2) No. 10-24 x 1/2" hex head screws [69]. • Tighten screws. ,J_ssen'MF_g _:opower "...
- Page 12 Line "V" (Vertical Center Line Line "H" Can Be of Door) Spring Line "H" Door Header Inside of Door Establish center line of door and header (Fig. 2-1). • Close door, • Measure door width. Mark center. NOTE: Line "H" Can Be Drawn Above Spring •...
- Page 13 install header bracket (Fig. 2-3) • Place bracket so: - center hole is on line "V." - all holes are on line "H." • Mark hole positions "A" and "B." • Drill 5/32" holes at marked positions. • Fasten bracket to header using two (2) 1/4" x 2" lag screws [79].
- Page 14 Top of Door Top of Door Top of Door Install door bracket (Fig. 2-6). , Contact door manufacturer. 14" MIN. Install door arms (Fig. 2-7). • Attach straight door arm to carriage. - slip straight door arm into slot at bottom of carriage as shown.
- Page 15 Line "V" (Vertical centerline of door) Top of door Inside of door Establish center (ine of door and header (Fig. 2-9). • Close door. • Measure door width. Mark center. • Use straight edge to draw vertical line "V." - down door about 6." - on top of door.
- Page 16 Install door braces CAUTION (See below). Header Door bracket Attach channel/rail assembly to header bracket (Fig. 2-13). • Fasten header end of the channel/rail to the header bracket with pin. • Install speed nut onto pin (Fig, 2-14). • Place cardboard packing under power head. Use additional support if needed.
-
Page 17: Mounting Methods
ht door arm [91] Bolt, 3/8-16 x 7/8" Curved door /" [92]e' ,-" 3/8-16 nut Mount power head (See Section 2 ALTERNATE MOUNTING METHODS). • Be sure rail assembly and power head are on door center line (line "V'). • Check the illustrations. Decide which mounting method you will use. - Page 18 Fs F_s _ ;ed Mounting brackets. • Mark both sides of garage door frame or wall 5" above floor (Fig. 3-1). • Hold bracket against door frame or wall. - Check if brackets extend out from wall far enough, so tongue of bracket is beyond door, tracks or any door hardware.
- Page 19 • Make wire attachments at STB's. - Splitting and stripping wire ends to be connected as shown (Fig. 3-6). - Loosen terminal screws. - Insert wire under flat plate and tighten screw. It does not matter which wire, white or striped, goes on which terminal (Fig.
- Page 20 Run wire from power head to wall control. , Place the wall control: Power head Striped - In sight of door. terminals l lLZ,:,_l ] i ,4J_l - At least 5 feet from floor, so small children can '-=_ I I I_I wall I If_l ,_ I...
- Page 21 Grounded outlet Operator power cord Fig. 5-1 Check local building codes. • Some building codes require direct wiring to a branch circuit. If direct wiring is NOT required, plug door operator into grounded outlet (Fig. 6-1). Return to Section 3 for SAFE-T-BEAM ® System alignment and troubleshooting.
- Page 22 STEALTH Before starting main limit switch settings, LOCK carriage onto rail assembly (See emergency release tag). Raise the door until the carriage engages with the inner-slide/bullet. Set "OPEN" limit switch (Fig 6-1). • Locate limit set switch on back of power head. •...
- Page 23 During the following steps, the motor protector open. Wait about 20 minutes for protector to reset. STEALTH C'LOSS_ pos _on befon_ s_'U_g FOF_CS Adjust the "OPEN" Force (Fig. 7-1). • Locate screw on back of power head marked "OPEN FORCE." , Gently turn screw counterclockwise until it stops.
- Page 24 During the following steps, the motor protector open. Wait about 20 minutes for protector to reset. Adjusting the "OPEN" limit switch (Fig. 8-1). • Run door to open position by pushing wall control, • Locate curved "OPEN" limit adjustment slot on back of power head.
- Page 25 • Press and release a remote control button. - LED on power head stops blinking. • Press and release same remote button again. Radio - LED goes out. Remote is now programmed. Program multi-button remote control • Repeat step 1 ("program one-button remote" for each button).
- Page 26 install light bulb(s) into socket(s). Do Not use short neck bulb(s). • Use bulb(s) rated for: Bend tabs up (2)_,__ - rough service. - vibration. - appliances. • 100 watt maximum. Slotted Bend two (2) slotted tabs up. This will activate the "living hinge"...
- Page 27 KEEP GARAGE DOORS PROPERLY BALANCED. See Owner's Manual. An improperly balanced door increases the risk of severe injury or death. Have a o _g__ _ o,_7_ Genie Factory Authorized Dealer make repairs to cables, spring assemblies, and other hardware. 8 SAVETHESE INSTRUCTIONS.
- Page 28 Use this guide to correct problems with your door operator. If these solutions do not work, call Customer Service. PROBLEM SOLUTIONS Check lock switch on wall console (See section 4). Operator does not run from wall control. Check the power source. •...
- Page 29 .._ _ ..¢_°_o .._ _o_ &&w t_1 _ _o_ _ PURPLE REEN WHITE BLUE • ON MODEL,S THAT HAVE ONLY ONE LIGHT THE WHITE WIRE F ROM POSITION UGHT THE BLUE WIRE F ROM POSlT_ON #11 AND THE LIGHT SOCKET ITSELF WILL BE OMITTED...
- Page 30 (6SXL-8) ExceleraterScrewDrive Extension Kit- An Extension that increases t he travelof a ScrewDriveOpener Pas d'exp@ditioncentre remboursement. Veuillez inclure un ch@queou un mandat bancaire, le payable fait B The Genie to accommodate aneight foot door. Company. N'envoyez pas d'argent comptant. Accordez de 3 El extensi6ndeslizante de Excelerator S crew Drive- Unaextensi6nparaaumentarlacarreradeun abridor 4 semaines pour la Iivraison.
- Page 31 NAME COMPANY, NUMBER NAME COMPANY, NUMBER NAME COMPANY, NUMBER NAME COMPANY, NUMBER NAME COMPANY, NUMBER NAME COMPANY, NUMBER...
- Page 32 Geographic scope: This warranty applies only to Genie products purchased in the United States, Canada or Mexico. What we will do: If your Genie product is defective,we will repair it or, at our option, replace it at no charge to you. If we repair your Genie product, we may use new or reconditioned replacement parts.