Table of Contents
Advertisement
Grill
Lighting
Instructions
1. Before
each
use, check
all hoses for cracks,
nicks,
cuts,
burns
or abrasions.
If a hose
is damaged
in any
way, do not use your grill before
replacing
the hose
with an authorized
part from
the Parts List. Also
make
sure
all gas supply
connections
are securely
tightened.
2. Familiarize
yourself
with the safety and Use and Care
instructions
in this manual.
Do not smoke
while
lighting
grill or checking
gas supply
connections.
3. Be sure
the LP Gas tank is filled or the Natural
Gas
Line is attached
to the gas source.
4. Open the Grill Lid.
5. Check
that the end of each Burner
Tube
is properly
located
over each Valve
Orifice.
Failure
to replace
a faulty
hose,
secure
gas
supply
connections
or to open
the
Lid
before
proceeding
to the
Lighting
Procedures
could
result
in a fire
or
explosion
that
could
cause
serious
bodily
injury,
death,
or property
damage.
6.
Set Control
Knobs to OFF and open the LP Gas tank
valve
SLOWLY
1/4 of a turn.
For Natural
Gas open
the Shut Off Valve at source.
|
Open
LP
Gas tank
OFF
7. Push and turn the LEFT
Control
Knob to IGN. Push
the Control
Knob
in to automatically
ignite the Burner.
|
HI
IGN
OFF
Main
Back
Infrared
Burner
Burner
Sear Burner
8. If ignition
does
not occur
in 5 seconds,
turn the burner
Control
Knob(s)
and gas source
OFF and conduct
a
leak test of ALL
gas connections
and gas sources
as
explained
in the Use and Care section
of this manual.
If no leaks
are detected,
wait 5 minutes
for any gas to
clear
and repeat
the lighting
procedure.
9. After one Burner
is lit, turn the tank valve SLOWLY
one
more 1/4 of a turn for 1/2 of one complete
turn.
10. Once
one Burner
is lit, the adjacent
Burner
can be lit
by turning
its Control
Knob
to HIGH.
Back Burner Lighting Instructions
1. Follow
steps
1 through
6 of the Grill Lighting
instructions.
2. Push and turn the Control
Knob
to IGN. Push the
Control
Knob
in to automatically
ignite the Burner.
Once the burner
is lit, turn the knob
back to ON,
keep
pressing
the knob
and holding
it for at least
10 seconds
before
releasing.
3. If ignition
does
not occur
in 5 seconds,
turn the
Control
Knob(s)
and gas source
OFF and conduct
a
leak test as explained
in the Use and Care
section
of this manual.
If no leaks are detected,
wait 5
minutes
for any gas to clear
and repeat
the lighting
procedure.
4. After Burner
is lit, turn the tank valve SLOWLY
one
more 1/4 of a turn for 1/2 of one complete
turn.
BACK BURNER
KNOB:
INFRARED BURNER KNOB:
|
IGN
OFF i O
j
.........
_'
--OFF
Infrared Sear Burner Lighting
Instructions
1. Follow
steps
1 through
5 of the Grill Lighting
Instructions.
2. Open
infrared
Sear
Burner
Lid.
3. Set Control
Knobs
to OFF and open
the LP gas
tank
valve SLOWLY
1/4 of a turn.
For Natural
Gas
open
the Shut Off Valve at source.
4. Push
and turn
the Control
Knob
to IGN.
Push
the
Control
Knob
in to automatically
ignite
the Burner.
Once
the burner
is lit, turn the knob
back to High,
keep
pressing
the knob
and holding
it for at least
10 seconds
before
releasing.
5. If ignition
does
not occur
in 5 seconds,
turn the
burner
Control
Knob(s)
and gas source
OFF and
conduct
a leak test as explained
in the Use and
Care
section
of this manual.
If no leaks
are
detected,
wait 5 minutes
for any gas to clear and
repeat
the lighting
procedure.
6. After Burner
is lit, turn the tank valve SLOWLY
one
more
1/4 of a turn for 1/2 of one complete
turn.
Manually Lighting Your Grill By Paper Match
To light your Main Burner
by match,
follow
steps
1 through
6 of the Grill Lighting
instructions.
Then,
light the match
and place it over the top opening
of the Lighting
Tube.
Push and turn the nearest
Control
Knob
to the HIGH
setting
to release
gas. The Burner
should
light
immediately.
Left Bowl
Panel
19
Lighting
Tube
Advertisement
Table of Contents
