Advertisement
Available languages
Available languages
Important Notes to the Installer
1. Read a llinstructions contained i nthese installation
instructions before installing t hecooktop.
2. Remove a llpacking material before connecting the
electrical supply t othecooktop.
3. Observe allgoverning c odes a ndordinances.
4. Besure to leave t hese instructions withtheconsumer.
Important Note to the Consumer
Keep these instructions withyourUse and
Care Guide for
future reference.
IMPORTANT
SAFETY
INSTRU
S
Be sure your cooktop is installed
and grounded
properly
by a qualified
installer
or service
technician.
This cooktop
must be electrkally
grounded
in
accordance
with
local codes or, in their absence,
with the Nationa[
Electrical Code ANSI/NFPA No.
70--[atest
edition
in the United States.
_The
electrical
power
to the cooktop
must
be shut
off while
line connections
are being
made.
Failure
to do so could
result
[n serious
injury
or death.
Provide
Electrical
Connection
Install the junction box under the cabinet and FUrl 120/
240 or 120/208 Volt, AC wire from tile main circuit
panel. NOTE: DO NOT connect tile wire to the circuit
panel at this time.
Electrical
Requirements
Observe all governing
codes and local ordinances.
1.
A 3-wire or 4-wire single phase 120/240 or 120/208
Volt, 60 Hz AC only electrical supply is required on a
separate circuit fused on both sides of the line (time-
delay fuse or circuit breaker is recommended). DO
NOT fuse neutral. The fuse size must not exceed the
circuit rating of the appliance specified on the
nameplate.
2.
This unit can consume up to 8,000 W at 240 Vac. A
circuit breaker of 40 Amp with wire gauge #10AWG
shall be used.
NOTE: Wire sizes and connections must conform with
tile fuse size and rating of tile appliance in accordance
with the National Electrical Code ANS!/NFPA No. 70-
latest edition and local codes and ordinances.
An extension
cord
must
not
be used
with
this
appliance.
Such use may
result
in a fire,
electrical
shock,
or other
personal
injury.
3.
The appliance should be connected to the fused
disconnect (or circuit breaker) box through flexible
armored or nonmetallic sheathed cable. The flexible
armored cable extending from this appliance should
be connected directly to tile grounded junction box.
The junction box should be located as shown in
Figure 2 with as much slack as possible remaining in
the (:able between tile box and the appliance, so it
can be moved if servicing is ever necessary.
4.
A suitable strain relief must be provided to attach
tile flexible armored cable to the junction box.
Unpacking
Instructions
1.
Unpack and visually inspect the cooktop.
2.
Be sure the bottle of (:leaner conditioner packed in the
literature bag is left where the user (:an find it easily. It
is important that the ceramic-glass cooktop be
pretreated before use. See Cooktop Cleaning and
Maintenance
section in the Use and Care Guide.
Electrical
Connection
Connect the flexible armored cable that extends from
tile surface unit to tile iunction box using a suitable
strain relief at the point the armored cable enters the
junction box. Then make the electrical connection as
follows.
Electrical
ground
is required
on this
appliance.
This app!iance
is equipped
with
a
copper
conductor
flexible
cable,
tf connection
is
made
to aluminum
house
wiring,
use onJy speciat
connectors
which
are approved
for joining
copper
and aluminum
wires
in accordance
with
the
National
Electrical
Code and
local
codes
and
ordinances,
improper
connection
of aluminum
house
wiring
to copper
leads
can result
in a short
circuit
or fire.
Follow
the connector
manufacturer
recommended
procedure
closely.
This appliance is manufactured with a supply wire and a
frame connected green or bare copper grounding wire.
Advertisement
