Renault Duster Handbook
  1. Manuals
  2. Brands
  3. Renault Manuals
  4. Automobile
  5. Duster
  6. Handbook

Renault Duster Handbook

Hide thumbs Also See for Duster:
Table of Contents

Advertisement

Quick Links

DUSTER
DRIVER'S HANDBOOK

Advertisement

Table of Contents
loading

Related Manuals for Renault Duster

Summary of Contents for Renault Duster

  • Page 1 DUSTER DRIVER’S HANDBOOK...
  • Page 2 Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please ELF has developed a complete range of lubricants for RENAULT: refer to your maintenance document. engine oils manual and automatic gearbox oils Benefiting from the research applied to Formula 1, lubricants are very high-tech products.

  • Page 3: Driving

    Welcome aboard your vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. –...
  • Page 5 Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........

  • Page 7: Table Of Contents

    Section 1: Getting to know your vehicle Keys/Radio frequency remote control ..........Locking and unlocking the doors .

  • Page 8: Keys/Radio Frequency Remote Control

    KEYS, RADIO FREQUENCY REMOTE CONTROL: general information (1/2) Key A Radio frequency remote Driver’s responsibility control B Never leave your vehicle 1 Coded key for ignition switch, with the key or remote con- doors and fuel filler cap. 2 Locking the doors and tailgate. trol inside and never leave a 3 Unlocking the doors and tailgate.

  • Page 9: Operating Range

    KEYS, RADIO FREQUENCY REMOTE CONTROL: general information (2/2) The remote control unit operating range This varies according to the environ- Replacement and additional keys ment. It is therefore important when or remote controls. handling the remote control to ensure You must only contact an approved that you do not lock or unlock the ve- Dealer: hicle by inadvertently pressing the but-...

  • Page 10: Locking The Doors

    RADIO FREQUENCY REMOTE CONTROL: use Doors are locked and unlocked using remote control unit B. It is powered by a battery which must be replaced (refer to the information on the “Radio frequency remote control: batteries” in Section 5). Locking the doors Unlocking the doors Press locking button 1.

  • Page 11: Locking And Unlocking The Doors

    LOCKING AND UNLOCKING THE DOORS (1/2) Manual locking Child safety From the outside To make it impossible for the rear doors to be opened from the inside, move Unlock the doors using the remote con- lever 2 on each door and check from trol (refer to information on the “Radio the inside that the doors are securely frequency remote control: use”...
  • Page 12 LOCKING AND UNLOCKING THE DOORS (2/2) Electric central locking Depending on the vehicle, it can be used to simultaneously lock or unlock the four doors and the boot. Lock or unlock the doors by pressing switch 3. The front door mechanism cannot be Driver’s responsibility locked if the door is open.

  • Page 13: Opening And Closing The Doors

    OPENING AND CLOSING THE DOORS Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves or to others by starting the engine, activating equipment such as the electric windows or by locking the...

  • Page 14: Engine Immobiliser System

    ENGINE IMMOBILISER This prevents the vehicle being Operating faults driven by anyone not in possession After the ignition has been switched of the vehicle’s coded ignition key. on, if warning light 1 continues to flash or remains continuously lit, there is a Operating principle system operating fault.

  • Page 15: Headrests

    FRONT HEADRESTS Adjusting the height of headrest A To refit headrests A or B Press tab 1 and simultaneously slide Insert headrest rods 2 into the holes (tilt the headrest to the required position. the seatback backwards if necessary). Push the headrest in until it locks in po- To raise the headrests A or B sition.

  • Page 16: Rear Headrests

    REAR HEADRESTS To reinstall headrests A Adjusting the height of the Position for using headrest B headrests A (depending on vehicle) and B (depending on the vehicle) Press lock tab 1 and simultaneously Raise the headrest until it locks to use slide the headrest to the required po- it in the high position.

  • Page 17: Front Seats

    FRONT SEATS To move forwards or Heated seats For safety reasons, carry backwards Depending on the vehicle, with the igni- out any adjustments when tion on, press switch 3. the vehicle is not being Lift bar 1 to release. Release the bar driven.

  • Page 18: Seat Belts

    SEAT BELTS (1/4) Before starting, adjust your driving Always wear your seat belt when trav- elling in your vehicle. You must also position and then have each occu- comply with the legislation of the par- pant adjust their seat belt to ensure ticular country you are in.

  • Page 19: Seat Belt Reminder Light

    SEAT BELTS (2/4) ß Seat belt reminder light Depending on the vehicle, it comes on when the engine is started if the driver’s seat belt is not fastened. When the vehicle is being driven, it comes on and a beep sounds for ap- proximately 2 minutes until the driver’s seat belt is fastened.
  • Page 20 SEAT BELTS (3/4) Rear side seat belts Rear centre seat belt A (depending on vehicle) Slowly unwind belt 8 and click buckle 9 into red catch 10. Remove buckle 15 from its housing 16. Slowly unwind belt 14 and click buckle 15 into black catch 12.
  • Page 21 SEAT BELTS (4/4) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the restraint system (belts and seats and their mountings) fitted originally. For special operations (e.g. fitting child seats) contact an approved Dealer. –...

  • Page 22: Methods Of Restraint In Addition To The Front Seat Belts

    METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/3) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt pretensioners; an accident. – chest-level load limiters; – No operation whatsoever is permitted on any part of the –...
  • Page 23 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/3) Driver’s and passenger air Operation bags This system is only operational when the ignition is switched on. These may be fitted to the front seats on the driver and passenger side (loca- If a severe frontal impact occurs, the tion A).
  • Page 24 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/3) All of the warnings below are given so that the air bag is not obstructed in any way when it is deployed and also to pre- vent the risk of serious injuries caused by items which may be dislodged when the air bag deploys. Warnings concerning the driver’s air bag –...

  • Page 25: Side Protection Devices

    SIDE PROTECTION DEVICES Side air bags These air bags may be fitted to the front seats and are deployed at the sides of the seats (door side) to protect the oc- cupants in the event of a severe side impact. Warnings concerning the side air bag –...

  • Page 26: Additional Methods Of Restraint

    ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The airbag is designed to complement the action of the seat belt.

  • Page 27: Child Safety: General Information

    CHILD SAFETY: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- ished growing.
  • Page 28 CHILD SAFETY: General information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
  • Page 29 CHILD SAFETY: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.

  • Page 30: Mounting A Child Seat

    CHILD SAFETY: mounting a child seat (1/2) Attachment via the seat belt Attachment with the ISOFIX system The seat belt must be adjusted to Authorised ISOFIX child seats are ap- ensure that it is effective in the event of proved in accordance with regulation harsh braking or an impact.
  • Page 31 CHILD SAFETY: mounting a child seat (2/2) The rings ISOFIX 1 are located be- The third ring of each side seat is used Attach the hook on the belt to one of the tween the seatback and the seat base to attach the upper strap on some child rings 3 (4x2 version) or 4 (4x4 version).

  • Page 32: Fitting A Child Seat

    CHILD SAFETY: fitting a child seat (1/6) In the front seat Some seats are not suitable for fitting child seats. The diagram on the follow- The laws concerning children travel- ing page shows you how to attach a ling in the front passenger seat differ in child seat.
  • Page 33 CHILD SAFETY: fitting a child seat (2/6) In the rear side seat Rear centre seat For the safety of the child in the for- ward-facing seat, do not move the seat A carrycot can be installed across the A child seat may only be fitted in this in front back past the middle of the vehicle and will take up at least two seat if it is equipped with an inertia-reel...
  • Page 34 CHILD SAFETY: fitting a child seat (3/6) Vehicles without air bag OR with air bag deactivated Child seat attached using the ISOFIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted.
  • Page 35 CHILD SAFETY: fitting a child seat (4/6) Vehicles with passenger air bag not deactivated Child seat attached using the ISOFIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted.
  • Page 36 CHILD SAFETY: fitting a child seat (5/6) The table below summarises the information already shown on the diagram on the previous pages, to ensure the regula- tions in force are respected. Front passenger Front passenger seat without air Rear centre Rear seat with air bag Weight of...
  • Page 37 CHILD SAFETY: fitting a child seat (6/6) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. IUF = Seat which, on equipped vehicles, allows forward-facing child seats with “Universal”...

  • Page 38: Deactivating/Activating The Front Passenger Airbag

    CHILD SAFETY: deactivating/activating the front passenger air bag (1/3) Deactivating the front To deactivate the passenger airbag, with the ignition off, press and turn passenger air bag button 1 to the OFF position. (depending on vehicle) With the ignition switched back on, it is To fit a rear-facing child seat on the essential to check that warning light 2, front passenger seat, you must deacti-...
  • Page 39 CHILD SAFETY: deactivating/activating the front passenger air bag (2/3) DANGER Since front passenger air bag triggering and the po- The passenger air bag must sition of a rear-facing child be activated or deactivated seat are incompatible, it is not per- with the ignition off.

  • Page 40: Operating Faults

    CHILD SAFETY: deactivating/activating the front passenger air bag (3/3) Activation of the front Operating faults passenger air bag It is forbidden to fit a rear-facing child (depending on vehicle) seat to the front passenger seat if the air bag activation/deactivation system You should reactivate the airbag as is faulty.

  • Page 41: Rear-View Mirrors

    REAR VIEW MIRRORS Door mirrors with electrical Door mirrors with manual Interior rear view mirror adjustment: adjustment Its position can be adjusted. When driv- ing at night, to avoid being dazzled by With the ignition on, move button 1: To adjust the mirror, move lever 2. the headlights of the vehicle behind, –...

  • Page 42: Driving Position

    DRIVING POSITION, LEFT-HAND DRIVE (1/4) The fittings described DEPEND ON THE VEHICLE VERSION AND COUNTRY 33 32 20 19 23 22 21 1.36...
  • Page 43 DRIVING POSITION, LEFT-HAND DRIVE (2/4) The fittings described DEPEND ON THE VEHICLE VERSION AND COUNTRY. 1 Side air vent. 11 Location for passenger air bag or 22 Location for ashtray or cup holder. storage compartment. 2 Stalk for: 23 4x2 (2WD) and 4x4 (4WD) mode –...
  • Page 44 DRIVING POSITION, LEFT-HAND DRIVE (3/4) The fittings described DEPEND ON THE VEHICLE VERSION AND COUNTRY 30 29 1.38...
  • Page 45 DRIVING POSITION, LEFT-HAND DRIVE (4/4) The fittings described DEPEND ON THE VEHICLE VERSION AND COUNTRY. 1 Side air vent. 11 Location for passenger air bag or 22 Mode selector 4x2 (2WD), 4x4 storage compartment. (4WD) or storage compartment. 2 Stalk for: –...

  • Page 46: Warning Lights

    WARNING LIGHTS (1/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Engine oil change warning Braking will then be as normal, without light the ABS. This lights up on the instrument panel Contact an approved dealer as soon as when an oil change is required.

  • Page 47: Electronic Fault Warning

    WARNING LIGHTS (2/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. ’ 4-wheel drive mode indica- If not, switch off the engine and allow It goes out after preheating is sufficient tor light it to cool before checking the coolant and the engine can be started.
  • Page 48 WARNING LIGHTS (3/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Ä Ü Toxic Fume Filter System Rear fog light tell-tale Not used Warning Light Æ î It comes on when the ignition is STOP light Not used switched on and then goes out.
  • Page 49 WARNING LIGHTS (4/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Warning lights on console B Front passenger air bag de- activation warning light. Refer to the information on “Child Safety” in Section 1. ß...

  • Page 50: Display And Indicators

    DISPLAY AND INDICATORS (1/2) Rev counter 1 (rpm × 1 000) Speedometer 2 (km or miles Fuel gauge 3 per hour) The number of squares lit shows the fuel level. When it is at minimum, the squares disappear and the low fuel Overspeed buzzer level warning light comes on.

  • Page 51: Coolant Temperature

    DISPLAY AND INDICATORS (2/2) Multifunction key 5 – Display selection By pressing the button you can shift from the total mileage recorder, trip mileometer and time or vice-versa. – Resetting the trip mileage re- corder Once the trip mileage display is se- lected, press and hold the button.
  • Page 52 TRIP COMPUTER AND WARNING SYSTEM (1/4) The information display DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Refer to the table on the following pages showing display examples. Display 1 Display selection key 3 Keep pressing key 3 briefly to scroll General reset and trip through the following information (de- pending on the vehicle) in sequence:...

  • Page 53: Trip Computer And Warning System

    TRIP COMPUTER AND WARNING SYSTEM (2/4) The information display DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Interpreting some of the – You may also notice that the aver- age fuel consumption increases values displayed after when the vehicle is stationary and resetting the engine idling.
  • Page 54 TRIP COMPUTER AND WARNING SYSTEM (3/4) The information display DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of display selections by repeatedly Interpreting the display pressing 3 a) Total mileage recorder. b) Trip mileage recorder. c) Fuel used since the last time the reset button was pressed. d) Average fuel consumption since the last time the reset button was pressed.
  • Page 55 TRIP COMPUTER AND WARNING SYSTEM (4/4) The information display DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of display selections by repeatedly Interpreting the display pressing 3 e) Estimated range with remaining fuel This range takes into account the average fuel consumption since the last time the reset button was pressed.

  • Page 56: Steering Wheel, Power-Assisted Steering

    STEERING WHEEL, POWER-ASSISTED STEERING Power Assisted Steering With the engine running, do not leave the steering wheel at full lock while sta- tionary as this may damage the power- assisted steering pump. With the engine switched off, or if there is a system fault, it is still possible to turn the steering wheel.

  • Page 57: Clock

    CLOCK If the electrical supply is cut (battery disconnected, broken supply wire, etc.), the clock will lose its time set- ting. The clock must be reset. Resetting the clock With the ignition on, select display 1 showing total mileage and clock. There are two ways to set the time: –...

  • Page 58: Audible And Visual Signals

    AUDIBLE AND VISUAL SIGNALS (1/2) Horn Direction indicators Press the end of the stalk 1. Move stalk 1 parallel to the steering wheel and in the direction you are going Depending on the vehicle, press on one to turn it. of areas 2.
  • Page 59 AUDIBLE AND VISUAL SIGNALS (2/2) Hazard warning lights é Press switch 3. This switch activates all four direction indicators and the side indicator lights simultaneously. It must only be used in an emergency to warn drivers of other vehicles that you have had to stop in an area where stop- ping is prohibited or unexpected, or that you are obliged to drive under special...

  • Page 60: Exterior Lighting And Signals

    EXTERIOR LIGHTING AND SIGNALS (1/2) á Main beam headlights With stalk 1 in dipped beam headlights position, move the stalk to- wards you. When the main beam headlights are lit up, an indicator light on the instrument panel lights up. To return to the dipped headlight posi- tion, pull the stalk towards you again.

  • Page 61: Front Fog Lights

    EXTERIOR LIGHTING AND SIGNALS (2/2) Turning off the fog lights Turn centre ring 3 again until the symbol for the fog light or for extinction position is opposite mark 4. The corresponding indicator light on the instrument panel goes out. The front and rear fog lights switch off when the exterior lights are switched off.

  • Page 62: Adjusting The Headlight Beam Height

    ADJUSTING THE BEAM HEIGHT Examples of positions for adjusting control A according to the load Driver alone or with front passenger Driver with one front passenger and one rear passenger Driver with one front passenger and two rear passengers Control A is used to adjust the height of the headlight beams according to the load.

  • Page 63: Windscreen Wiper

    WINDSCREEN WASHER/WIPER, DE-ICING (1/3) Windscreen wiper With the ignition on, pull stalk 1 towards you. A brief pull will trigger a single sweep In frosty weather, make sure that of the wipers, in addition to the wind- the wiper blades are not stuck by ice screen washer.

  • Page 64: Rear Screen Wiper

    WINDSCREEN WASHER/WIPER, DE-ICING (2/3) Rear screen washer/ wiper With the ignition on, turn the end of stalk 1 to align the symbol with mark 2. When the stalk is released, it returns to the rear wipe position. Rear screen wiper With the ignition on, turn the end of stalk 1 to align the symbol with mark 2.
  • Page 65 WINDSCREEN WASHER/WIPER DE-ICING (3/3) Heated rear screen With the engine running, press button 3 (the indicator light on the instrument panel lights up). This function de-ices/demists the rear screen and the electric de-icing rear- view mirrors (depending on the vehi- cle).

  • Page 66: Fuel Tank (Filling With Fuel)

    FUEL TANK (1/3) Usable capacity of the fuel tank: To open fuel flap A, insert your finger in 50 litres approximately. recess B. To close, push the fuel filler flap A by Fuel filler cap: this is spe- hand as far as it will go. Depending cific to the vehicle type.

  • Page 67: Fuel Grade

    FUEL TANK (2/3) Fuel grade Vehicles running on ethanol-based Filling with fuel fuel Always use a high-grade fuel that Insert the nozzle to open valve A and Always use unleaded petrol or fuel complies with the legislation in force insert it fully before turning it on to fill containing a maximum of 85 percent in each country.
  • Page 68 FUEL TANK (3/3) Persistent smell of fuel If you notice a persistent smell of fuel you should: – stop the vehicle as soon as traffic conditions allow and switch off the ignition; – switch on the hazard warning lights and ask your passengers to leave the vehicle and stay clear of the traffic;...
  • Page 69 Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in, Ignition switch ............Starting, stopping the engine .

  • Page 70: Running In, Ignition Switch

    RUNNING IN, IGNITION SWITCH Petrol version Ignition on position M For the first 600 miles (1,000 km), do The ignition is switched on: not exceed 78 mph (130 km/h) in the – petrol version: the engine may be highest gear, or 3,000 to 3,500 rpm. started.

  • Page 71: Starting/Stopping The Engine

    STARTING/STOPPING THE ENGINE É Starting the engine Petrol injection Diesel injection Engine warm or cold In very cold conditions (temperatures Turn the ignition key to ignition “On” po- below –20°C): so that it is easier to – Turn the key to the start position sition M, and hold this position until the start the engine, switch on the ignition without depressing the accelera-...

  • Page 72: Special Features Of Petrol Versions

    SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: If you notice any of the above operating faults, have the necessary repairs car- – driving for long periods when the low ried out as soon as possible by an ap- fuel level warning light is lit;...

  • Page 73: Running Out Of Fuel

    SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with an injec- tion pump which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of – ensure that the battery is always fully the gear selected.

  • Page 74: Engine Adjustments

    ADVICE: antipollution, fuel economy and driving (1/3) Maintenance Exhaust gas monitoring system By virtue of its design, moderate fuel consumption and initial settings, your The exhaust gas monitoring system will It should be noted that failure to respect vehicle conforms to current antipol- detect any operating faults in the vehi- antipollution regulations may lead to lution regulations.
  • Page 75 ADVICE: antipollution, fuel economy and driving (2/3) – Double declutching and accelerating before switching off are unnecessary in modern vehicles. Vehicles with 4x4 (4WD) trans- – Do not try to maintain the same mission speed up a hill, accelerate no more On flat, level ground, with the vehi- than you would on the level.
  • Page 76 ADVICE: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (es- pecially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.

  • Page 77: Environment

    ENVIRONMENT Emissions – At the end of the vehicle’s service life, it should be sent to approved Your vehicle has been designed to centres to ensure that it is recycled. emit fewer greenhouse gases (CO2) – In all cases, comply with local legis- while in use, and therefore to consume lation.

  • Page 78: Gear Lever, Handbrake

    GEAR LEVER, HANDBRAKE To apply Pull lever 2 upwards and make sure the vehicle is immobilised. To select reverse gear Handbrake When driving, make sure the handbrake is com- (vehicle stationary) To release pletely released. Follow the grid shown on knob 1. Pull lever 2 up slightly, press button 3 Risk of overheating.

  • Page 79: Transmission: 4-Wheel Drive (4Wd)

    TRANSMISSION: 4-wheel drive (4WD) (1/4) “AUTO" mode To activate this mode, turn selector 1 to the “AUTO” position. Operating principle “AUTO” mode automatically distributes the engine torque between the front and rear axles according to the road condi- tions and the vehicle speed. This po- sition optimises roadholding.
  • Page 80 TRANSMISSION: 4-wheel drive (4WD) (2/4) To deactivate this mode, turn selector 1 After one minute, the system switches This problem may be resolved by ‘ to “2WD” or “AUTO” mode depending changing the tyres. Always use four to the “AUTO” position. The indi- on the position of the selector.
  • Page 81 TRANSMISSION: 4-wheel drive (4WD) (3/4) Electronic stability program and Operating faults In this case, we recommend that you stop as soon as possible to allow the traction control when driving off- If the system detects an operating system to cool down (until the warning road fault, it automatically switches to “2WD”...
  • Page 82 TRANSMISSION: 4-wheel drive (4WD) (4/4) All-wheel drive system – Irrespective of the mode selected, do not start the engine if one or more wheels are not in contact with the ground (eg. when the vehicle is on a jack or roller bench). –...

  • Page 83: Driver Correction Devices And Aids

    DRIVER CORRECTION DEVICES/AIDS (1/4) ABS (anti-lock braking Special feature of 4-wheel drive ve- Depending on the vehicle, this is com- posed of: hicles system) – the (anti-lock braking In 4WD Lock mode, the system may Under heavy braking, the ABS prevents system);...
  • Page 84 DRIVER CORRECTION DEVICES/AIDS (2/4) Emergency brake assist with Operating faults electronic brake distribution – If the warning light on the in- (depending on the vehicle) strument panel comes on while you This system supplements the ABS are driving, the brakes will still and helps reduce vehicle stopping dis- work normally without ABS;...

  • Page 85: Electronic Stability Program

    DRIVER CORRECTION DEVICES/AIDS (3/4) Special feature of 4-wheel drive and 2-wheel drive vehicles (depending on the vehicle) Disabling the ESP function In some situations (driving on very wet ground: snow, mud, etc. or driving with snow chains fitted), the system may reduce the engine output to limit wheel- spin.
  • Page 86 DRIVER CORRECTION DEVICES/AIDS (4/4) Note: the function is automatically re- Operating faults activated when the ignition is switched When the system detects an operating on, or when the speed exceeds 30 mph Ò ù (50 km/h) in AUTO and 2WD modes, fault, warning lights and approximately 36 mph (60 km/h) in light up on the instrument panel.

  • Page 87: Selector Lever

    AUTOMATIC TRANSMISSION (1/3) Driving in automatic mode Move lever 1 to position D. In the majority of traffic conditions, you will not have to touch the gear selector lever again: the gear will be changed automatically at the right time and at the most suitable engine speed be- cause the automatic system takes into account the vehicle load and road con-...
  • Page 88 AUTOMATIC TRANSMISSION (2/3) Special cases In certain driving conditions (e.g.: to protect the engine) the “automated system” may change the gear automat- ically. Likewise, to prevent incorrect manoeu- vres, a gear change may be refused by the automatic system: in this case the gear display flashes for a few seconds as a warning.

  • Page 89: Automatic Transmission

    AUTOMATIC TRANSMISSION (3/3) – If the road contour and bends in Parking the vehicle the road do not allow you to stay in When the vehicle is stopped, move the automatic mode (e.g.: in mountain- lever to position P while keeping your ous areas), it is recommended that foot on the brake pedal: the gearbox is you switch to manual mode.
  • Page 90 2.22...

  • Page 91: Your Comfort

    Section 3: Your comfort Air vents, air outlets ............. . Air conditioning: information and advice on use .

  • Page 92: Air Vents, Air Outlets

    AIR VENTS, air outlets (1/2) 1 Left-hand side air vent 6 Right-hand side window demister vent 2 Left-hand side window demister vent 7 Right-hand side air vent 3 Windscreen demisting vents 8 Front passenger footwell heater outlets 4 Centre air vents 9 Rear passenger footwell heater 5 Control panel outlets (depending on the vehicle)
  • Page 93 AIR VENTS, air outlets (2/2) To remove bad odours from your ve- hicles, only use the systems designed for this purpose. Consult an approved Dealer. Centre and side air vents Direction To direct the air flow, swivel air vent 1 Air flow or 3.

  • Page 94: Passenger Compartment

    HEATING, VENTILATION, AIR CONDITIONING (1/4 Close the dashboard vents to direct all the air to the foot wells. The air flow is distributed be- tween all the air vents, the front side window demister outlets, the windscreen demisting vents and the footwells.
  • Page 95 HEATING, VENTILATION, AIR CONDITIONING (2/4 Fuel consumption increases when the air conditioning is being used (switch it off when it is not required). Switching air conditioning on Note: the air conditioning may be used in all conditions but does not operate or off when the external temperature is low.
  • Page 96 HEATING, VENTILATION, AIR CONDITIONING ( 3/4) Prolonged use of this position can lead to condensation forming on the side windows and wind- screen and problems due to the use of non-renewed air in the passenger compartment. It is therefore advisable to return to normal operation (external air) by moving control D to the right once you are out of the polluted area.
  • Page 97 HEATING, VENTILATION, AIR CONDITIONING (4 Heated rear screen (depending on vehicle) With the engine running, press button E (the warning light on the in- strument panel comes on). This function de-ices/demists the rear screen and the electric de-icing rear- view mirrors (depending on the vehi- cle).

  • Page 98: Air Conditioning: Information And Advice On Use

    AIR CONDITIONING: information and advice on use Fuel consumption Operating faults You will normally notice an increase As a general rule, contact your ap- in fuel consumption (especially proved dealer in the event of an op- when driving in town) when the air erating fault.
  • Page 99 ELECTRIC WINDOWS (1/3) Electric front windows From the front passenger Switches in B seat With the ignition on, press switch 3 If fitted on the vehicle, the switches will or 4 to lower the window to the required be placed in A or B. Operate switch 5.
  • Page 100 ELECTRIC WINDOWS (2/3) Electric rear windows From the driver’s seat From the rear seats (depending on the vehicle) With the ignition on, press switch 8 or 9 Operate switch 10. With the ignition on, press switch 6 to lower the window to the required or 7 to open the window or lift switch 6 level.
  • Page 101 ELECTRIC WINDOWS (3/3) Safety of rear occupants The driver can prevent op- eration of the rear elec- tric windows by pressing switch 11. Driver’s responsibility Never leave your vehicle with the key or remote control inside and never leave a child (or a pet) un- supervised, even for a short while.

  • Page 102: Interior Lighting

    INTERIOR LIGHTING Courtesy light Map reading light (depending on the vehicle) Automatic operation of interior Pressing switch 1 provides: lighting Pressing switch 2 provides: – continuous lighting; (depending on the vehicle) – continuous lighting; – or temporary lighting by opening one –...

  • Page 103: Sun Visor/Grab Handle

    SuN VISOR/GRAB HANDLE Sun visor Grab handle 7 Vanity mirror (depending on the vehicle) Pivot sun visor 1 or 5 against the wind- This offers support and can be held The passenger sun blind is fitted with screen. when the vehicle is being driven. a courtesy mirror 6 on the passenger Do not use these for getting into or out side.

  • Page 104: Cigar Lighter

    ASHTRAYS/CIGAR LIGHTER/ACCESSORIES SOCkET Cigar lighter 2 With the ignition on, push in cigar lighter 2. It will spring back with a click when it is ready. Pull it out to use. After use, re- place it without pushing it all the way in. Accessories socket 2 It is provided for connecting acces- sories approved by our Technical...

  • Page 105: Passenger Compartment Storage Space And Fittings

    PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (1/4) Passenger side glove box This glove box can be used to store A4 format documents. Pull handle 1 to open it. Inside the cover, section 2 has been provided for pens, maps, etc. Precautions during use Cover A in the bottom of the glove box protects a socket reserved ex-...
  • Page 106 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (2/4) Centre console storage Centre console storage compartment 3 compartment 4 (or radio location) (or location of the 4x2 (2WD) and 4X4 (4WD) mode selector) Place for cups or ashtray 5 Ensure that no hard, heavy or pointed objects are When cornering, accelerat- placed in the “open”...

  • Page 107: Storage Compartment

    PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (3/4) Storage compartment 6 Front door storage Dashboard upper storage (or passenger air bag location) compartments 7 compartment 8 (depending on the vehicle) Ensure that no hard, heavy or pointed objects are Nothing should be placed placed in the “open”...
  • Page 108 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (4/4) Front seat storage pockets 9 Bottle holders 10 It can hold a 1.5 litre bottle. Rear storage compartment 11 (or location for electric rear window Ensure that no hard, heavy control). or pointed objects are placed in the “open”...

  • Page 109: Rear Bench Seat

    REAR BENCH SEAT When refitting the seat- back, make sure it is cor- rectly locked in place. If seat covers are fitted, make sure these do not prevent the seatback latch from locking in. Make sure that the seat belts are positioned correctly.

  • Page 110: Manual Control

    TAILGATE Manual control Electric central locking To open, insert the key in the lock and The tailgate is locked and unlocked at turn it (movement A). the same time as the doors. Remove the key and press button 1. To open, press the button 1 and lift the Lift the tailgate.

  • Page 111: Transporting Objects In The Luggage Compartment

    TRANSPORTING OBjECTS IN THE LuGGAGE COMPARTMENT Ensure that the load is evenly distrib- uted over the largest loading surface to prevent damage to the vehicle. Always place objects being transported so that their longest side rests against the back of the rear bench seatbacks, as with normal loads (example A) or against the back of the front seats when the rear bench seatbacks are folded...

  • Page 112: Luggage Compartment Cover

    LuGGAGE COMPARTMENT COVER (1/2) Position for use A Position for use B Position for use C Gently pull the two handles 1 located Remove the two ends 5 of the luggage underneath the luggage compartment compartment cover on the rear bench cover and place the two ends 2 in the seat side from the housings 6 in each housings 4 in each side of the luggage...

  • Page 113: Compartment Cover

    LuGGAGE COMPARTMENT COVER (2/2) Refitting the luggage compartment cover To refit it, proceed in the reverse order to removal. Removing the luggage cover Gently pull the two handles 1 located underneath luggage compartment cover D and remove the two ends 2 from their housings.

  • Page 114: Roof Bars

    LONGITuDINAL ROOF BARS When these are fitted to the vehicle, you can transport luggage or additional accessories (bike rack, ski rack, etc.) on a roof rack or on transverse roof For information on the range of bars attached to the longitudinal roof equipment adapted to your ve- bars 1 or directly on these bars.
  • Page 115 Section 4: Maintenance Bonnet ............... . Engine oil level: general information .

  • Page 116: Bonnet

    BONNET (1/2) Opening the bonnet To open the bonnet, pull handle 1. Lift the bonnet and guide it upwards; it Unlocking the bonnet catch is held by strut 3. To unlock, raise the bonnet slightly and release hook 2 by pushing tab 4 to the left.

  • Page 117: Closing The Bonnet

    BONNET (2/2) Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and lower it to 30 cm above the closed position, then release it. It will latch automatically under its own weight.

  • Page 118: Engine Oil Level: General Information

    ENGINE OIL LEVEL: general information It is normal for an engine to use oil for lubrication and cooling of moving parts and it is sometimes necessary to top up the level between oil changes. Exceeding the maximum engine oil level However, contact an approved dealer if more than 0.5 litres is being consumed The oil level should only be read with...

  • Page 119: Engine Oil Level: Topping Up/Filling

    ENGINE OIL LEVEL: topping up/filling (1/2) Topping up/filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on dipstick 2 is (for instance, before the engine is between 1.5 and 2 litres, depending...

  • Page 120: Oil Change

    ENGINE OIL LEVEL: topping up/filling (2/2) Oil change Resetting the alert after an oil change If there is an abnormal or repeated Service interval: refer (depending on the vehicle) drop in the fluid level, please consult Maintenance Service Booklet for your an authorised dealer.

  • Page 121: Levels

    LEVELS (1/3) Level Topping up It is normal for the level to drop as the After any operation on the hydraulic cir- brake shoes become worn, but it must cuit, a specialist must replace the fluid. never drop lower than the “MINI” warn- Only use fluids approved by our ing line shown on brake fluid reser- Technical Department (and taken from...

  • Page 122: Windscreen Washer Reservoir

    LEVELS (2/3) Coolant level checking frequency Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...
  • Page 123 LEVELS (3/3) Power-assisted steering fluid reservoir 4 or 5 Level: for a correct level when cold, with the engine switched off and on level ground, it must be visible between If you feel any variation in the ef- the “MINI” and “MAXI” marks on reser- fectiveness of the power-assisted voir 4 or 5.

  • Page 124: Filters

    FILTERS The replacement of filter elements (air If clogging level indicator 2 reaches filter, passenger compartment filter, 100%, consult an approved dealer as diesel filter, etc.) is scheduled in the soon as possible to have the filter re- maintenance operations for your vehi- placed.

  • Page 125: Tyre Pressure

    TyRE PRESSURE Tyre safety and use of snow chains Refer to the information on “Tyres” in Section 5 for the servicing con- ditions and, depending on the ver- sion, the use of chains. Special note For vehicles used fully laden (maximum permissible all-up...

  • Page 126: Battery

    BATTERy Replacing the battery As this operation is complex, we advise you to contact an approved dealer. Battery 1 does not require any mainte- Label A nance. Observe the indications on the battery: – 2 Naked flames and smoking forbid- den;...
  • Page 127 BODyWORK MAINTENANCE, ENGINE COMPARTMENT (1/3) you should not: A well-maintained vehicle has a longer – Use hard brushes to clean alloy service life. It is therefore recom- wheels. These can scratch or – Degrease or clean mechanical com- mended that attention is paid to the out- damage the wheel’s protective coat- ponents, underneath the body, parts side of the vehicle on a regular basis.
  • Page 128 BODyWORK MAINTENANCE, ENGINE COMPARTMENT (2/3) you should – After driving off-road (eg. on muddy, – salt deposited in the wheel arches dusty or sandy terrain) quickly clean and underneath the body after – Respect local regulations about the radiator from the outside of the driving in areas where the roads washing vehicles (e.g.
  • Page 129 BODyWORK MAINTENANCE, ENGINE COMPARTMENT (3/3) – After cleaning your vehicle, check – Remember to visit the body shop pe- the brakes while driving at low speed riodically in order to maintain your to ensure that the braking efficiency anticorrosion warranty. Refer to the has not been reduced by the water.

  • Page 130: Interior Trim Maintenance

    INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Fabrics (seats, door trim, A well-maintained vehicle will have a longer service life. It is therefore ad- (e.g.: instrument panel, clock, exterior etc.) visable to maintain the vehicle interior temperature display, radio display). Dust fabrics regularly.
  • Page 131 INTERIOR TRIM MAINTENANCE (2/2) Removing/refitting factory What you should not do fitted removable equipment You are strongly advised not to place in the vehicle items such as air fresheners, perfume etc. near the air vents as these could If you need to remove equipment to damage the dashboard fittings.
  • Page 132 4.18...

  • Page 133: Practical Advice

    Section 5: Practical advice Tools ............... . . Puncture .

  • Page 134: Tools

    TOOLS Accessing the tools Jack 3 Wheelbrace 4 To use the jack, undo nut 2. When refit- This is used to tighten/loosen the wheel The tools are located in the luggage ting, fold the jack before placing it in its bolts and, depending on the vehicle, to compartment.

  • Page 135: Puncture

    PUNCTURE (1/2) In the event of a puncture, depending on the vehicle, you will have: An emergency spare wheel or tyre in- flation kit (refer to the information on the following pages). Emergency spare wheel 4x2 To store the wheel in the cage: version (2WD) –...
  • Page 136 PUNCTURE (2/2) Note: ensure that the emergency spare wheel or punctured wheel and the wheel tray are correctly posi- tioned so that the luggage compart- ment carpet can be properly fitted. After lowering, check that luggage compartment carpet 7 is correctly positioned in its indexing stops to prevent it from being damaged.

  • Page 137: Tyre Inflation Kit

    TYRE INFLATION KIT (1/3) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
  • Page 138 TYRE INFLATION KIT (2/3) – press switch 5 to inflate the tyre to the recommended pressure (check the label affixed to the edge of the driver’s door); – after a maximum of 5 minutes, stop inflating and read the pressure (on the pressure gauge 4);...
  • Page 139 TYRE INFLATION KIT (3/3) – affix driving recommendation – if the pressure is greater than 1.3 bar label 10 to the dashboard where it but less than the recommended can easily be seen by the driver; pressure (refer to the label affixed to –...
  • Page 140 WHEEL TRIM/WHEELS Central wheel trim with Central wheel trim with visible wheel bolts visible wheel bolts (example: wheel trim 1) (example: wheel trim 2) The bolts are directly accessible. Remove it using the hubcap tool, by in- serting the hook near a wheel bolt. To put it back, position hooks 4 in rela- tion to bolts 3.

  • Page 141: Changing A Wheel

    CHANGING A WHEEL (1/2) Mark hole 1, which is the nearest to Switch on the hazard warn- the wheel in question. The jack must ing lights. be fitted in this location. Offer up jack 3 horizontally and position jack head 2 Park the vehicle away from under the sill.
  • Page 142 CHANGING A WHEEL (2/2) If the vehicle is not equipped with a jack or wheelbrace, you can obtain these from your approved dealer. Note: ensure that the emergency spare wheel or punctured wheel and Tighten the bolts, checking that the the wheel tray are correctly posi- wheel is correctly positioned on its hub tioned so that the luggage compart-...

  • Page 143: Tyres

    TYRES (1/3) Tyre and wheel safety When the tyre tread has been worn to the level of the warning strips, they The tyres are the only contact between become visible 2: it is then neces- the vehicle and the road, so it is essen- sary to replace your tyres because the tial to keep them in good condition.

  • Page 144: Tyre Pressures

    TYRES (2/3) Tyre pressures Fitting new tyres Pressures should be checked when the tyres are cold; ignore higher pressures Adhere to the tyre pressures (including which may be reached in hot weather the emergency spare wheel). The tyre or following a fast journey. For safety reasons, this op- pressures should be checked at least If tyre pressures cannot be checked...

  • Page 145: Changing Wheels Around

    TYRES (3/3) Use in winter Snow or Winter tyres We would recommend that these be Chains fitted to all four wheels to ensure that 2-wheel drive version (2WD) your vehicle retains maximum adhe- sion. Snow chains must be fitted to the front wheels.

  • Page 146: Dipped Beam Headlights

    FRONT LIGHTS: changing bulbs (1/3) The bulbs detailed below can be re- Do not touch the bulb glass. Hold it placed. However, we recommend that by its base. these be replaced by an approved It is essential to use anti-UV bulbs so dealer if this proves difficult.
  • Page 147 FRONT LIGHTS: changing bulbs (2/3) Front side light Remove bulb holder 7. Remove bulb 8. Bulb type: W5W. Remove cover A. When the bulb has been changed, make sure you refit cover A correctly. The engine may be hot The bulbs are under pres- during operations in close sure and can break when proximity.
  • Page 148 FRONT LIGHTS: changing bulbs (3/3) Main beam headlights Direction indicator lights Remove cover B. Turn bulb holder C fully anticlockwise and remove it. Release spring 9 and remove bulb 12 with connector 10. Replace bulb 14. Unclip the bulb from its connector. Bulb type: PY21W.
  • Page 149 FOG LIGHTS: changing bulbs Additional lights If you wish to fit fog lights or long range headlights to your vehicle, consult an approved dealer. Any operation on (or modi- fication to) the electrical system must be performed by an approved Dealer Front fog lights 1 since an incorrect connection might Consult an approved dealer.

  • Page 150: Rear Lights

    REAR LIGHTS: changing bulbs (1/3) Rear lights 7 Reversing light Pear-shaped, bayonet type bulb, P Open the tailgate and undo nuts 1, then 21 W. release light unit 2 by pulling it rear- wards. Rear fog light Release clips 3 to remove bulb holder 4. Pear-shaped, bayonet type P 21 W bulb.
  • Page 151 REAR LIGHTS: changing bulbs (2/3) High-level brake light Unclip tab 12 carefully (movement A) Remove bulb 13. and turn it an eighth of a turn (move- Bulb type: P 21 W. The bulb for high-level brake light 9 ment B) to release the bulb holder 11. may be accessed through the luggage compartment.
  • Page 152 REAR LIGHTS: changing bulbs (3/3) Number plate light Unclip light 14 by pressing tab 15 using a flat-blade screwdriver or similar. Unclip lens 17 and take out bulb 16. Bulb type: W 5 W. 5.20...
  • Page 153 INDICATOR LIGHTS: changing bulbs Unclip indicator light 1 (using a flat- blade screwdriver or similar positioned at A to move the indicator light towards the outside of the vehicle). Turn bulb holder 2 a quarter of a turn (movement B) and take out bulb 3 (movement C).

  • Page 154: Courtesy Light

    INTERIOR LIGHTS: changing bulbs (1/3) Courtesy light Remove the bulb concerned. Bulb type 2: W5W. Unclip lens 1 using a flat-blade screw- driver or similar. The bulbs are under pres- sure and can break when replaced. Risk of injury. 5.22...

  • Page 155: Glove Box Light

    INTERIOR LIGHTS: changing bulbs (2/3) Glove box light Press tab 4 to release lens 6 and access bulb 5. (depending on the vehicle) Bulb type: W5W. Unclip light 3 using a flat-blade screw- driver or similar, by pressing on the tab to move the light towards the inside of the unit.
  • Page 156 INTERIOR LIGHTS: changing bulbs (3/3) Luggage compartment light Press tab 9 to release lens 8. Remove the bulb 10. Bulb type: W5W. Unclip light 7 using a flat-blade screw- driver or similar, by pressing on tab 6 to move the light towards the inside of the luggage compartment.

  • Page 157: Fuses

    FUSES (1/3) Passenger compartment fuses Tweezers 2 Fuses in engine compartment B Some functions are protected by fuses If any electrical component does not Release the fuse using tweezers 2, lo- located in the engine compartment work, check the condition of the fuses. cated on the back of flap A.
  • Page 158 FUSES (2/3) Allocation of fuses in the passenger compartment (the presence of certain fuses DEPENDS ON THE VEHICLE EQUIPMENT LEVEL) Symbol Allocation Symbol Allocation Symbol Allocation Central locking of doors ḽ Electric front windows and tailgate î Radio Interior lighting Rear screen de-icing ß...
  • Page 159 FUSES (3/3) Allocation of fuses in the passenger compartment (the presence of certain fuses DEPENDS ON THE VEHICLE EQUIPMENT LEVEL) Symbol Allocation Symbol Allocation Left-hand main beam Engine immobiliser headlight Left-hand dipped beam Reversing light and rear Ë headlight screen wiper Right-hand dipped Power-assisted steering beam headlight...

  • Page 160: Battery: Troubleshooting

    BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any consumers (cour- The battery charger must be com- tesy lights, etc.) are switched off patible with a battery with nominal before disconnecting or reconnect- voltage of 12 volts.
  • Page 161 BATTERY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.
  • Page 162 RADIO FREQUENCY REMOTE CONTROL: battery Replacing the battery Replace battery 3 according to the di- rection marked on the cover. Unscrew screw 1 then unclip cover 2. Note: It is not advisable to touch the electronic circuit in the key cover when replacing the battery.

  • Page 163: Wiper Blades

    WIPER BLADES Check the condition of the wiper blades. You are responsible for their service life: – clean the blades, windscreen and rear screen regularly with soapy water; – do not use them when the wind- screen or rear screen are dry; –...

  • Page 164: Towing: Breakdown

    TOWING: breakdown (1/3) Towing procedure The steering wheel must be un- locked and the ignition key must be in position M (ignition on) to pro- vide stop lights and hazard warning lights on the towed vehicle. At night the vehicle must have its lights on. Unhitch the trailer, etc., if one is being towed.
  • Page 165 TOWING: breakdown (2/3) Off-road recovery If your vehicle is stuck in sand, snow or mud, attach a flexible towing device (towing belt or other device specially designed for this purpose) to the front or rear towing point (refer to the in- formation on “Front and rear towing points”...
  • Page 166 TOWING: breakdown (3/3) Vehicle equipped with an automatic gearbox If the lever is stuck in P, even though you are de- pressing the brake pedal, When storing the tools, the lever can be released ensure they are securely re- manually. placed in the luggage com- To do this, unclip the cover at the partment, in their original...
  • Page 167 TOWING: towing equipment A = 893 mm. Permissible nose weight, maxi- mum permissible towing weight braked and unbraked: Refer to the information on “Weights” in Section 6. Refer to the manufacturer’s instruc- tions for information on how to fit and operate the towing equipment. Please keep these instructions with the rest of the vehicle documenta- tion.

  • Page 168: Fitted Audio Equipment

    FITTED AUDIO EQUIPMENT (1/2) Radio location 1 If your vehicle is not fitted with an audio system, one can be fitted and locations have been provided for: – the radio 1; – front speakers 2; – rear speakers 3. – In all cases, it is very important to follow the manufacturer’s instructions care- fully.
  • Page 169 FITTED AUDIO EQUIPMENT (2/2) Location for front speaker 2 Location for rear speaker 3 Unclip cover 2 using a flat-blade screw- Unclip cover 3 using a flat-blade screw- driver or similar. driver or similar. 5.37...

  • Page 170: Accessories

    ACCESSORIES Before fitting an electrical or If you are using an anti-theft electronic device (particu- device, only attach it to the larly for transmitters/receiv- brake pedal. ers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle.

  • Page 171: Operating Faults

    OPERATING FAULTS (1/5) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. The starter is activated POSSIBLE CAUSES WHAT TO DO Warning lights dim or fail to come on; Battery terminals disconnected, Retighten them, reconnect them or clean the starter does not run.
  • Page 172 OPERATING FAULTS (2/5) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pres- Check the tyre pressures; if this is not the sures, incorrectly balanced or dam- cause, have their condition checked by an aged. approved dealer.
  • Page 173 OPERATING FAULTS (3/5) On the road POSSIBLE CAUSES WHAT TO DO The oil pressure warning light takes Loss of oil pressure. Stop the vehicle: contact a an approved a long time to go out or remains lit dealer. during acceleration. The oil change warning light remains Warning not reset after oil change.
  • Page 174 OPERATING FAULTS (4/5) On the road POSSIBLE CAUSES WHAT TO DO The power-assisted steering be- Belt broken. Have the belt replaced. comes heavy. Lack of power-assisted steer- For maintenance operations on the power-assisted ing oil in the pump. steering, contact an approved dealer. The engine overheats.
  • Page 175 OPERATING FAULTS (5/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. The wiper does not stop. Faulty electrical controls. Consult an approved dealer.
  • Page 176 5.44...

  • Page 177: Technical Specifications

    Section 6: Technical specifications Vehicle identification plate ............Engine specifications .

  • Page 178: Vehicle Identification Plate

    VEHICLE IDENTIFICATION PLATE XXXXX Quote the details given on identifica- Vehicle identification plate A 6 Technical specifications of vehicle. tion plate A on all letters or orders. 1 Vehicle type and chassis number. 7 Vehicle paint reference. 2 MMAC (Maximum permissible 8 Equipment level.

  • Page 179: Engine Identification Plates

    ENGINE IDENTIFICATION PLATES Quote the details given on identifica- tion plate B on all letters or orders. (Location varies depending on engine) 1 Engine type 2 Engine suffix 3 Engine number...
  • Page 180 DIMENSIONS (in metres) 1.560 0.822 2.673 0.820 4.315 1.634 * 1.690 * 1.567 (*) Unladen 1.822...

  • Page 181: Engine Specifications

    ENGINE SPECIFICATIONS Versions 1.6 16V 2.0 16V 1.5 dCi Engine type (see engine plate) Cubic capacity (cc) 1,598 1998 1,461 Type of fuel Petrol Diesel Octane rating It is essential to use unleaded petrol and this must The label located in the fuel filler be of the octane rating stated on the label inside the flap indicates the authorised fuels.
  • Page 182 WEIGHTS (in kg) The weights shown are for a basic vehicle without options: they will vary depending on the equipment level of your ve- hicle. Please consult an authorised dealer. Versions 1.6 16V 2.0 16V 1.5 dCi 1.6 16V 2.0 16V 1.5 dCi Weights shown on the vehicle identification plate (refer to the Maximum permissible all-up weight (MMAC)
  • Page 183 SPARE PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
  • Page 184 SERVICE SHEETS (1/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 185 SERVICE SHEETS (2/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 186 SERVICE SHEETS (3/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 187 SERVICE SHEETS (4/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 188 SERVICE SHEETS (5/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 189 SERVICE SHEETS (6/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 190 ANTICORROSION CHECk (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.14...
  • Page 191 ANTICORROSION CHECk (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.15...
  • Page 192 ANTICORROSION CHECk (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.16...
  • Page 193 ANTICORROSION CHECk (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.17...
  • Page 194 ANTICORROSION CHECk (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.18...

  • Page 195: Alphabetical Index

    AlphAbeticAl index (1/4) child booster seat ..........1.21 → 1.23 ABS ...............2.15 → 2.18 child restraint/seat ..........1.21 → 1.31 accessories................ 5.38 child safety............1.7, 1.21 → 1.31 accessories - installation ........... 5.38 child seats..............1.21 → 1.31 accessories socket ............3.14 children ..............1.5 → 1.7 adjusting your driving position ......1.10, 1.12 → 1.15 cigar lighter ................ 3.14 advice on antipollution ...........5.25 → 5.27 clock ..................
  • Page 196 AlphAbeticAl index (2/4) headlight flashers ........... 1.52 – 1.53 4 wheel drive (4WD) ..........2.11 → 2.14 headrest..............1.9 – 1.10 faults heating and air conditioning system ......3.2 → 3.8 operating faults ..........5.39 → 5.43 heating system ............3.2 → 3.8 filter ..................4.10 horn ................ 1.52 – 1.53 air filter ................. 4.10 hubcap tool ................
  • Page 197 AlphAbeticAl index (3/4) adjustment ..............1.56 practical advice ........5.2 – 5.4, 5.8 → 5.43 lights: puncture............ 5.3 – 5.4, 5.9 – 5.10 adjusting ..............1.56 brake lights ............5.18 – 5.19 radio dipped beam headlights ......1.54, 5.14 → 5.16 fitting a radio ............. 5.36 – 5.37 direction indicators .......1.52 – 1.53, 5.14 → 5.16 rear bench seat..............
  • Page 198 AlphAbeticAl index (4/4) sun visor ................3.13 warning buzzer ..............1.55 warning lights............1.40 → 1.49 tailgate ................3.20 washing ..............4.13 → 4.15 tanks and reservoirs weight .................. 6.6 brake fluid ..............4.7 weights ................6.6 coolant ................4.8 wheelbrace ................5.2 tanks and reservoirs: windows ..............3.9 → 3.11 windscreen washer ............
  • Page 200 à999107097Rë ï ò ä RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

Table of Contents