Renault Clio Handbook
Hide thumbs Also See for Clio:
Table of Contents

Advertisement

CLIO
DRIVER'S HANDBOOK

Advertisement

Table of Contents
loading

Summary of Contents for Renault Clio

  • Page 1 CLIO DRIVER’S HANDBOOK...
  • Page 2 Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please ELF has developed a complete range of lubricants for RENAULT: refer to your maintenance document. engine oils manual and automatic gearbox oils Benefiting from the research applied to Formula 1, lubricants are very high-tech products.
  • Page 3: Driving

    This handbook may also contain information about items of equipment to be introduced later in the model year. Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle.
  • Page 5: Table Of Contents

    Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........
  • Page 7 RENAULT card: general information, use, deadlocking ........
  • Page 8: Battery Life

    3 Switch on the courtesy lighting re- “Keycard battery low” appears on the instrument panel (refer to the informa- motely. Driver’s responsibility tion on the “RENAULT card: battery" in 4 Unlocking/locking the tailgate Never leave your vehicle section 5). 5 Integrated key.
  • Page 9 RENAULT card, cle and all of its RENAULT cards to then insert the RENAULT card into an approved Dealer to initialise the the card reader to start the vehicle.
  • Page 10: Luggage Compartment

    If a door or the luggage compartment is open RENAULT card not detected or not properly shut, or if a RENAULT alarm card is still in the reader, the doors and If a door is opened when the engine...
  • Page 11: Unlocking The Vehicle

    “HANDs-fREE” RENAULT CARD: use (1/3) Unlocking the vehicle On equipped vehicles, in addition to With the RENAULT card in zone 1 and the functions of the remote control the vehicle locked, press button 3 on RENAULT card, it can be used to lock/...
  • Page 12: Locking The Vehicle

    The vehicle will lock. If a door or the boot is open or not closed properly, the vehicle will quickly lock/unlock. Note: a RENAULT card must be within the vehicle's access zone (zone 1) to be able to lock the vehicle using the button.
  • Page 13 Risk of serious injury. After locking/unlocking the vehicle using the buttons on the RENAULT card, "hands-free" locking and unlocking is deactivated. To reactivate the “hands-free” mode: restart the vehicle.
  • Page 14 RENAULT CARD: deadlocking To deactivate deadlocking Unlock the vehicle using button 1 on the RENAULT card. The hazard warning lights flash once to indicate that the doors have been un- locked. To activate deadlocking If the vehicle is equipped with a dead-...
  • Page 15: Opening And Closing The Doors

    With the doors unlocked, pull handle 3. Pull handle 4. front doors With the doors unlocked, pull handle 1. special feature of the RENAULT “hands-free” card With the doors locked, press button 2 on handle 1 of one of the two front doors and pull towards you.
  • Page 16 OPENING AND CLOsING THE DOORs (2/3) Lights-on reminder buzzer Door/tailgate open buzzer If you have switched off the ignition If a door (or boot) is open or not prop- and left the lights switched on, a re- erly closed, as soon as the vehicle minder buzzer will sound when a door reaches a speed of approximately is opened.
  • Page 17 OPENING AND CLOsING THE DOORs (3/3) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves Child safety or to others by starting the engine, activating equipment such as the...
  • Page 18: Locking/Unlocking Doors

    “RENAULT Card” information in Section 1. In certain cases, the RENAULT card may not work: – if the RENAULT card battery is weak, flat, etc. – if equipment operating on the same frequency as the card (mobile phones, etc.) is used;...
  • Page 19 Unlocking the vehicle from the outside is only possible with the RENAULT card in the vehicle's access zone or using Interior locking/unlocking the key integrated in the RENAULT card.
  • Page 20: Operating Principle

    RENAULT ANTI-INTRUDER DEVICE (RAID) Activating/deactivating the function With the engine running, press button 1 for approximately five seconds until you hear a beep. Operating faults If you experience an operating fault (no automatic locking, the indicator light incorporated in button 1 does not light up when trying to lock the open- ing elements, etc.), firstly check that the...
  • Page 21: Front Headrests

    fRONT HEADREsTs To raise the headrest Raise the headrest to its highest po- sition (tilt the seatback backwards if necessary). Press button 1 and lift the headrest to release it. To refit the headrest Insert the headrest rods into the holes (tilt the seatback backwards if neces- sary).
  • Page 22: Heated Seats

    fRONT sEATs (1/3) To move the seat forwards or To raise or lower the seat To tilt the seatback backwards base Turn control knob 4 and tilt the seat- back to the desired position. Lift handle 1 to unlock. Release the Move lever 2 as many times as neces- handle once the seat is in the correct sary upwards or downwards.
  • Page 23 fRONT sEATs (2/3) To reposition the passenger seat For your safety, attach any Make sure that nothing prevents the transported objects when seat from moving. the seat is in the table po- sition. – Activate control 5 to unlock the seat- back;...
  • Page 24 fRONT sEATs (3/3) Central armrest 5 To store away the armrest Lift the armrest to the storage posi- To adjust the armrest upwards tion A. Check that it is correctly locked. Lift armrest to the desired position. To adjust the armrest downwards Lift the armrest to the storage position along the seat back, then lower it.
  • Page 25: Seat Belts

    sEAT BELTs (1/4) Before starting, first adjust your driv- Always wear your seat belt when trav- elling in your vehicle. You must also ing position, then ask all occupants comply with the legislation of the par- to adjust their seat belts to ensure ticular country you are in.
  • Page 26: Front Seat Belts

    sEAT BELTs (2/4) ß front seat belt reminder warning light This lights up on the central display when the engine is started then, if the driver’s or front passenger’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approxi- mately 12 mph (20 km/h), it flashes and a bleep sounds for around 2 minutes.
  • Page 27 sEAT BELTs (3/4) Rear side seat belts 7 Rear centre seat belt Fasten sliding buckle 10 into the corre- sponding red catch 12. The belts are locked, unlocked and Unwind belt 9 slowly from its housing, adjusted in the same way as the front then fasten buckle 8 into the corre- belts.
  • Page 28 sEAT BELTs (4/4) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. –...
  • Page 29 METHODs Of REsTRAINT IN ADDITION TO THE fRONT sEAT BELTs (1/4) Depending on the vehicle, they will con- – Have the entire restraint sist of: system checked following – front seat belt inertia reel preten- an accident. sioners; – No operation whatso- –...
  • Page 30: Methods Of Restraint In Addition To The Front Seat Belts

    METHODs Of REsTRAINT IN ADDITION TO THE fRONT sEAT BELTs (2/4) Load limiter Airbags for driver and front passenger Above a certain severity of impact, this mechanism is used to limit the force of Fitted to the driver and passenger side. the belt against the body so that it is at The presence of this equipment is in- an acceptable level.
  • Page 31 METHODs Of REsTRAINT IN ADDITION TO THE fRONT sEAT BELTs (3/4) Operating faults Operation å This system is only operational when Warning light 4 will light up on the ignition is switched on. the instrument panel when the ignition In a severe frontal impact, the air bags is turned on and then go out after a few inflate rapidly, cushioning the impact seconds.
  • Page 32 METHODs Of REsTRAINT IN ADDITION TO THE fRONT sEAT BELTs (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...
  • Page 33 METHODs Of REsTRAINT IN ADDITION TO THE REAR sIDE sEAT BELTs force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. –...
  • Page 34 sIDE PROTECTION DEVICEs side Airbags This airbag may be fitted to each of the front seats and is activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. Warning relating to the side airbag –...
  • Page 35: Additional Methods Of Restraint

    ADDITIONAL METHODs Of REsTRAINT All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when it inflates. The airbag is designed to complement the action of the seat belt.
  • Page 36: Child Safety: General Information

    CHILD sAfETY: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- Driver’s responsibility ished growing.
  • Page 37 CHILD sAfETY: General information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
  • Page 38 CHILD sAfETY: choosing a child seat Rear-facing child seats forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.
  • Page 39: Choosing Child Seat Mounting

    CHILD sAfETY: choosing a child/baby seat mounting (1/2) Attachment using the IsOfIX There are two ways of attaching child Before using an ISOFIX seats: via the seat belt or using the system child seat that you pur- ISOFIX system. Authorised ISOFIX child seats are ap- chased for another vehicle, proved in accordance with regulation check that its installation is...
  • Page 40 CHILD sAfETY: choosing a child/baby seat mounting (2/2) The two rings 1 are located between Rear seats front passenger seat the seatback and the seat base of the The 2 belt should be positioned be- Attach the belt hook 2 to the ring 5. seat and are identified by a marking.
  • Page 41: Fitting A Child Seat

    CHILD sAfETY: fitting a child seat (1/6) In the front seat In the rear side seat Some seats are not suitable for fitting child seats. The diagram on the follow- The laws concerning children travel- A carrycot can be installed across the ing page shows you how to attach a ling in the front passenger seat differ in vehicle and will take up at least two...
  • Page 42 CHILD sAfETY: fitting a child seat (2/6) The table below summarises the information already shown in the diagram on the following pages, to ensure the appli- cable regulations are respected. five door and estate versions Weight of front passenger Rear side Type of child seat seat size IsOfIX Rear centre seat...
  • Page 43 CHILD sAfETY: fitting a child seat (3/6) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. UD = Seat which only allows a rear-facing standardised “Universal”...
  • Page 44 CHILD sAfETY: fitting a child seat (4/6) Visual installation of five door and estate versions Child seat fitted using the IsOfIX mounting ü Seat which allows a ISOFIX child seat to be attached. ± The rear seats are fitted with an anchorage point which allows a for- ward-facing ISOFIX child seat with uni- versal approval to be attached.
  • Page 45 CHILD sAfETY: fitting a child seat (5/6) View of the utility version installation Child seat fitted using the IsOfIX mounting ü seat which allows an ISOFIX child seat to be fitted. ± The passenger seat is fitted with an anchorage point for attaching a universal ISOFIX forward-facing child seat.
  • Page 46 CHILD sAfETY: fitting a child seat (6/6) The table below summarises the information already shown on the diagram on U = Seat which allows a child seat with the previous page, to ensure the regulations in force are respected. “Universal” approval to be installed using a seat belt;...
  • Page 47: Deactivating, Activating The Front Passenger Airbag

    CHILD sAfETY: deactivating/activating the front passenger air bag (1/3) DANGER Since front passenger airbag triggering and the position of a rear-facing child seat are incompatible, NEVER use a restraining device for rear- facing children on a seat with an ACTIVATED AIRBAG in front of it. This provides a risk of DEATH or sERIOUs INJURY to the CHILD.
  • Page 48 CHILD sAfETY: deactivating/activating the front passenger air bag (2/3) The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since front passenger airbag triggering and the position of a rear-facing child seat are incompatible, NEVER use a restraining device for rear-...
  • Page 49 CHILD sAfETY: deactivating/activating the front passenger air bag (3/3) Operating faults It is forbidden to fit a rear-facing child seat to the front passenger seat if the airbags activation/deactivation system is faulty. Allowing any other passenger to sit in that seat is not recommended. Contact your approved dealer as soon as possible.
  • Page 50: Driving Position

    DRIVING POsITION: LEfT-HAND DRIVE (1/2) 11 12 1.44...
  • Page 51: Instrument Panel

    26 Bonnet release control. 5 Multimedia system voice control button. 16 Glovebox. 27 Controls for: – electric headlight beam adjust- 17 RENAULT card reader. 6 Stalk: ment, – windscreen and rear screen – instrument panel lighting dimmer, wash/wipe; 18 Gear lever.
  • Page 52 DRIVING POsITION: RIGHT-HAND DRIVE (1/2) 5 6 7 12 13 14 1.46...
  • Page 53 7 Door electric locking switch. 15 Controls for: socket. – electric headlight beam adjust- 8 Centre air vents. 23 RENAULT card reader. ment, – instrument panel lighting dimmer, 9 Stalk: 24 Engine start/stop button. – direction indicator lights; – activate/deactivate the parking –...
  • Page 54 WARNING LIGHTs (1/4) The display of information shown below DEPENDs ON THE VEHICLE EQUIPMENT AND COUNTRY. š å side light warning light Air bag warning light This lights up when the ignition is switched on and goes out after a few á...
  • Page 55 WARNING LIGHTs (2/4) The display of information shown below DEPENDs ON THE VEHICLE EQUIPMENT AND COUNTRY. À Handbrake on and brake cir- Oil pressure warning light cuit incident warning light This lights up when the ignition This comes on when the ignition is is switched on and goes out after a few switched on and goes out as soon as seconds.
  • Page 56 WARNING LIGHTs (3/4) The display of information shown below DEPENDs ON THE VEHICLE EQUIPMENT AND COUNTRY. Ä Toxic fume filter system Anti-lock braking warning Warning Light light This lights up when the ignition is For vehicles equipped with this option, switched on and goes out after a few the light comes on when the ignition is seconds.
  • Page 57 WARNING LIGHTs (4/4) The display of information shown below DEPENDs ON THE VEHICLE EQUIPMENT AND COUNTRY. Φ Š‰ speed limiter and cruise fuel economy indicator light control indicator lights This lights up to advise you to change to a higher gear (up arrow) or See the information on the “Speed lim- lower gear (down arrow).
  • Page 58: Displays And Indicators

    DIsPLAYs AND INDICATORs Rev counter 1 speedometer 3 Low engine oil level (graduations x 1000) (km or miles per hour) warning 4 When the engine is started, display 4 Coolant temperature Overspeed buzzer alerts the driver when the oil level is at indicator 2 its minimum.
  • Page 59: On-Board Computer 1

    ON-BOARD COMPUTER: general information (1/2) f) distance travelled; g) average speed; h) distance before service; – service counter; – oil change counter; i) cruise control/speed limiter pro- grammed speed; j) clock and temperature; k) trip log, operating faults and informa- tion message readout.
  • Page 60 ON-BOARD COMPUTER: general information (2/2) Interpreting some of the Automatic resetting of the values displayed after journey parameters resetting Resetting occurs automatically when the maximum value of any of the pa- The values showing average fuel con- rameters is exceeded. sumption, range and average speed will become more stable and reliable the further you travel after pressing the...
  • Page 61 ON-BOARD COMPUTER: trip settings (1/6) The display of information shown below DEPENDs ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101778 km 112.4 km a) Total mileage and trip mileage recorder. Fuel used b) Journey parameters. fuel used.
  • Page 62 ON-BOARD COMPUTER: trip settings (2/6) The display of information shown below DEPENDs ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected Range e) Estimated range with remaining fuel. 541 km The value is displayed after driving 400 metres. Distance 522 km f) Distance travelled since last reset.
  • Page 63 ON-BOARD COMPUTER: trip settings (3/6) The display of information shown below DEPENDs ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer without mileage- before-service message h) Mileage before service. OIL CHANGE IN SCHEDULE SERVICE Distance remaining until the next service (displayed in WITHIN 100km 30000km/24 MOIS...
  • Page 64 ON-BOARD COMPUTER: trip settings (4/6) The display of information shown below DEPENDs ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with mileage- before-service message SERVICE IN SERVICE INTERVALS h) Mileage before service or oil change. 30,000 kms / 12 months Mileage before service With the ignition switched on but the engine not run-...
  • Page 65 ON-BOARD COMPUTER: trip settings (5/6) The display of information shown below DEPENDs ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with distance before next service message (cntd.) OIL CHANGE IN Mileage before service SERVICE INTERVALS 30,000 kms / 24 months With the ignition switched on and the engine not run-...
  • Page 66 ON-BOARD COMPUTER: trip settings (6/6) The display of information shown below DEPENDs ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected Speed limiter 90 km/H i) Cruise control/speed limiter programmed speed. Refer to the information on the “Speed limiter” and “Cruise control” in Section 2. Cruise control 90 km/H j) Clock and temperature.
  • Page 67 Interpreting the display selected “Parking brake on” Indicates that the parking brake has been applied. “Please remove keycard” Request to remove the RENAULT card from the reader when you leave the vehicle. “Traction control off” Indicates that you have deactivated the ASR function.
  • Page 68 TRIP COMPUTER AND WARNING sYsTEM: operating fault messages © These appear with the warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log.
  • Page 69 TRIP COMPUTER AND WARNING sYsTEM: warning message ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traf- fic conditions allow. stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages.
  • Page 70: Steering Wheel/Power-Assisted Steering

    sTEERING WHEEL/POWER-AssIsTED sTEERING Power Assisted steering Never drive with an inadequately charged battery. Variable power assisted steering The variable power assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier during parking manoeuvres (for added comfort) whilst the force needed to steer increases...
  • Page 71: Clock And Exterior Temperature

    CLOCK AND EXTERIOR TEMPERATURE (1/2) 9°C 12:00 Display A Then press and hold button 3 to con- firm the time set. To access display 1 for setting the time, The minutes flash; repeatedly press or press button 2 or 3. Wait for a few sec- press and hold button 2 to set them.
  • Page 72 CLOCK AND EXTERIOR TEMPERATURE (2/2) External temperature indicator special note: When the exterior temperature is - 3°C to + 3°C, the °C characters flash (sig- nalling a risk of ice on the road). External temperature in- Display B dicator Vehicles fitted with touch-screen As ice formation is related multimedia, navigation aid systems, to climatic exposure, local...
  • Page 73: Door Mirrors

    REAR VIEW MIRRORs Heated door mirrors With the engine running, mirror de- icing is activated simultaneously with rear screen de-icing/demisting. folding door mirrors (depending on vehicle) Move button 1 to position F: the door mirrors fold away. To reset them for driving, return to position C, D or E.
  • Page 74: Exterior Lighting And Signals

    EXTERIOR LIGHTING AND sIGNALs (1/3) Dipped beam headlights Manual operation Turn the ring 2 until the symbol is oppo- site mark 3. This indicator light on the instrument panel comes on. Automatic operation (depending on vehicle) Turn ring 2 until the AUTO symbol is op- posite mark 3: with the engine running, the dipped beam headlights switch on or off automatically depending on the...
  • Page 75: Switching Off The Lights

    EXTERIOR LIGHTING AND sIGNALs (2/3) switching off the lights There are two possibilities: – Manually, move ring 2 to position 0; – automatically, the lights will go out when the engine is switched off, the driver’s door is opened or the vehicle is locked.
  • Page 76: Front Fog Lights

    EXTERIOR LIGHTING AND sIGNALs (3/3) Rear fog light switching off the lights Turn centre ring 4 on the stalk Turn ring 4 again until mark 5 is oppo- until the symbol faces mark 5, then re- site the symbol for the fog light you wish lease it.
  • Page 77: Audible And Visual Signals

    AUDIBLE AND VIsUAL sIGNALs Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. One-touch mode When driving, it is possible that the steering wheel may not be turned suf- ficiently to return the stalk automatically to its starting position.
  • Page 78: Headlight Beam Adjustment

    HEADLIGHT BEAM ADJUsTMENT for manual settings Examples of positions for adjusting control A according to the load Driver alone or with front passenger Driver with one front passenger and two or three rear passengers On vehicles fitted with this function, Driver with one front control A allows you to adjust the height of the beams according to the load.
  • Page 79 WINDsCREEN WAsH/WIPE (1/2) Vehicles with automatic wiper function With the engine running, move stalk 1 – A park. – B automatic wiper function When this position is selected, the system detects water on the wind- screen and triggers the wipers at a suitable wiping speed.
  • Page 80: Windscreen Washer

    WINDsCREEN WAsH/WIPE (2/2) In freezing or snowy weather, ensure they are not stuck to the windscreen (including the central area located behind the interior rear-view mirror) and the rear screen before starting the wipers (risk of motor overheat- ing). Check the condition of the wiper blades.
  • Page 81: Special Note

    REAR sCREEN WAsH/WIPE Rear screen wash/wipe With the ignition on, turn the end of stalk 1 to align mark 2 with the symbol. In freezing or snowy weather, ensure When the stalk is released, it returns to they are not stuck to the windscreen the rear wipe position.
  • Page 82: Fuel Grade

    fUEL TANK (1/3) fuel grade Petrol version It is essential to use unleaded petrol. Use a high-grade fuel that complies The octane rating (RON) must comply with the legislation in force in each with the information given on the label country and which must comply with on the cover A.
  • Page 83: Fuel Tank Filling With Fuel

    fUEL TANK (2/3) filling with fuel With the ignition off, insert the nozzle and insert it fully before turning it on to fill the fuel tank (risk of splashing). Keep the nozzle in this position through- out the entire filling operation. When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts...
  • Page 84 Running out of fuel on diesel Vehicles without priming bulb 4 wiring, fuel circuit, injectors, pro- versions Insert the RENAULT card into the 5 tective covers, etc.) as this may be Vehicles with priming bulb 4 card reader. Press the start button 3...
  • Page 85 Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in ..............Starting, stopping the engine .
  • Page 86: Running In

    RUNNING IN Petrol version Diesel version For the first 600 miles (1,000 km), do For the first 900 miles (1,500 km), not exceed 78 mph (130 km/h) in the do not exceed 2,500 rpm. After com- highest gear, or 3,000 to 3,500 rpm. pleting this mileage you may drive faster, although you may only expect You may only expect top performance...
  • Page 87: Starting/Stopping The Engine

    To start, press button 1. If a gear is en- Starting with the tailgate gaged, depress the clutch pedal to start open (in hands-free mode) the vehicle. In this case, the RENAULT card must not be located in the luggage compart- ment.
  • Page 88 In certain cases, the hands-free RENAULT card, insert the card into RENAULT card may not work: reader 2; – when the RENAULT card battery is – vehicles with a RENAULT “hands- drained, flat battery, etc. free” card, with the card in the pas- –...
  • Page 89 If the card is no longer in the reader cle, especially if you have when you try to switch the engine off, your RENAULT card with the message “No keycard Press and you, check that the engine hold” appears on the instrument panel: is completely switched off.
  • Page 90: Stop And Start Function

    SToP AND START function (1/3) This system enables a reduced fuel Special feature of the automatic  consumption and lower greenhouse engine re-start Warning light is displayed on the gas emissions. instrument panel. This notifies you that Under certain conditions, the engine The system is activated automatically the engine is on standby.
  • Page 91 SToP AND START function (2/3) Conditions preventing the Special cases – the “Clear View” function is activated (please see the information on “Air standby of the engine – Depending on the vehicle, while the conditioning” in Section 3); system is operating and the engine Depending on the vehicle, certain con- –...
  • Page 92 SToP AND START function (3/3) operating faults The system is automatically reactivated each time the vehicle is started using When the message “Check Stop & the start button (please see “Starting, Start” appears on the instrument panel stopping the engine)”. and the integrated warning light 2 lights Special note: engine on standby, up on the switch 1, the system is deac-...
  • Page 93: Special Features Of Petrol Versions

    SPECIAL FEATURES oF PETRoL VERSIoNS The following operating conditions: If you notice any of the above operating faults, have the necessary repairs car- – driving for long periods when the low ried out as soon as possible by an ap- fuel level warning light is lit;...
  • Page 94: Special Features Of Diesel Versions

    SPECIAL FEATURES oF DIESEL VERSIoNS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with injection equipment which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of – ensure that the battery is always fully the gear selected.
  • Page 95: Gear Lever/Handbrake

    GEAR LEVER/HANDbRAkE Handbrake To release: Pull the lever 3 up slightly, press button 2 and then lower the lever to the floor. The red warning light on the instrument panel will light up if you are driving with an incorrectly released handbrake. To apply: Pull lever 3 upwards.
  • Page 96: Eco-Driving

    ECo-DRIVING (1/2) Depending on the vehicle, you will have various functions which enable you to lower your fuel consumption: – the rev counter; – the gear change indicator; – the driving style indicator; – the journey record and eco-driving advice via the multimedia display; –...
  • Page 97: Eco Mode

    ECo-DRIVING (2/2) ECo mode Activating the function Press switch 4. ECO mode is a function which opti- mises fuel consumption. It acts on all The 5 ECO warning light comes on the elements which consume fuel (engine instrument panel to confirm activation. power, heating and/or air conditioning, It is possible to regain your motor per- etc).
  • Page 98: Engine Adjustments

    ADVICE: antipollution, fuel economy and driving (1/3) Aiding fuel economy Your vehicle complies with criteria for Have your vehicle adjusted and recycling and recovering vehicles at the checked by an approved Dealer, in ac- Depending on the vehicle, in order to end of their service life which will come cordance with the instructions given in optimise consumption, an indicator light...
  • Page 99 ADVICE: antipollution, fuel economy and driving (2/3) Exhaust gas monitoring – Brake as little as possible. If you an- ticipate an obstacle or bend in ad- system vance, you may then simply release The exhaust gas monitoring system will the accelerator pedal. detect any operating faults in the vehi- –...
  • Page 100 ADVICE: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (es- pecially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
  • Page 101: Environment

    ENVIRoNMENT Emissions Your vehicle has been designed with – At the end of the vehicle’s service respect for the environment in mind for life, it should be sent to approved Your vehicle has been designed to its entire service life: during production, centres to ensure that it is recycled.
  • Page 102: Driver Correction Devices And Aids

    DRIVER CoRRECTIoN DEVICES AND AIDS (1/4) Anti-lock braking system operating faults: Depending on the vehicle, this is com- posed of: (AbS) © – anti-lock braking system (AbS); – lit up on the in- Under heavy braking, the ABS prevents – electronic stability control (ESC) strument panel alongside mes- the wheels from locking, allowing the with understeer control and trac-...
  • Page 103: Electronic Stability Program

    DRIVER CoRRECTIoN DEVICES AND AIDS (2/4) Electronic stability program Understeer control operating faults (ESC) with understeer control This system optimises the action of the When the system detects an operat- and traction control (ASR) ESC in the case of pronounced under- ing fault the message “Check ESC”...
  • Page 104: Emergency Brake Assist

    DRIVER CoRRECTIoN DEVICES AND AIDS (3/4) Emergency brake assist Hazard warning lights switching on Depending on the vehicle, these may This system supplements the ABS light up in the event of sudden decel- and helps reduce vehicle stopping dis- eration. tances.
  • Page 105 DRIVER CoRRECTIoN DEVICES AND AIDS (4/4) Hill start assistance The hill start assistance This function assists the driver when system cannot completely starting on hills. It prevents the vehicle prevent the vehicle from from rolling backwards, depending on rolling backwards in all sit- the slope, by automatically applying the uations (extremely steep gradients, brakes when the driver lifts his/her foot...
  • Page 106: Speed Limiter

    CRUISE CoNTRoL/SPEED LIMITER: speed limiter function (1/3) Controls Switching on The speed limiter function helps you stay within the driving speed limit that  1 Main “On/Off” switch. Press switch 1 on side . Indicator you choose, known as the limit speed. light 6 comes on, lit orange, and the 2 Limit speed activation, storage and message “Speed limiter”...
  • Page 107 CRUISE CoNTRoL/SPEED LIMITER: speed limiter function (2/3) Varying the limit speed Exceeding the limit speed The limit speed may be changed by re- It is possible to exceed the limit speed peatedly pressing: at any time. To do this: press the accel- erator pedal firmly and fully (beyond –...
  • Page 108 CRUISE CoNTRoL/SPEED LIMITER: speed limiter function (3/3) Recalling the limit speed If a speed has been saved, it can be re- called by pressing switch 4 ((R)). Putting the function on Switching off the function standby The speed limiter function is deac- tivated if you press switch 1: in this The speed limiter function is suspended case a speed is no longer stored.
  • Page 109 CRUISE CoNTRoL/SPEED LIMITER: cruise control function (1/4) This function is an addi- tional driving aid. However, the function does not take the place of the driver. Therefore, it can under no circum- Controls The cruise control function helps you to stances replace the driver’s respon- maintain your driving speed at a speed sibility to respect speed limits and to...
  • Page 110 CRUISE CoNTRoL/SPEED LIMITER: cruise control function (2/4) Switching on Activating cruise control Driving  At a steady speed (above 18 mph Once a cruising speed is stored and Press switch 1 side (30 km/h approximately)) press switch 2 the cruise control function is active, Indicator light 6 comes on, lit green, or (+): the function is activated and the you may lift your foot off the accelera-...
  • Page 111 CRUISE CoNTRoL/SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While it is being exceeded, the cruising speed flashes on the in- strument panel. Then, release the accelerator: after a few seconds, the vehicle will automati- cally return to its set cruising speed.
  • Page 112 CRUISE CoNTRoL/SPEED LIMITER: cruise control function (4/4) Returning to the cruising speed If a speed is stored, it can be recalled, once you are sure that the road con- ditions are suitable (traffic, road sur- face, weather conditions, etc.). Press switch 4 (R) if the vehicle speed is above 20 mph (30 km/h).
  • Page 113: Selector Lever

    AUToMATIC TRANSMISSIoN (1/3) Selector lever 1 operation Gear change paddles 5 P: park With the selection lever 1 in position P, The paddles 5 enable you to change switch on the ignition. gear while the gear lever is in ‘manual R: reverse mode’...
  • Page 114: Automatic Gearbox

    AUToMATIC TRANSMISSIoN (2/3) Driving in automatic mode Driving in manual mode Special circumstances With the selection lever 1 in position D, Put lever 1 into position D. – If the bends and road surface do move the lever to the left. Shifting the not allow you to stay in automatic In most road conditions you will en- lever repeatedly allows you to change...
  • Page 115: Automatic Transmission

    AUToMATIC TRANSMISSIoN (3/3) Parking the vehicle operating faults When the vehicle is stopped, move the – when driving, if the ‘check gearbox’ lever to position P while keeping your message appears on the instrument foot on the brake pedal: the gearbox is panel, it indicates a fault.
  • Page 116: Parking Distance Control

    PARkING DISTANCE CoNTRoL (1/2) operating principle Ultrasonic detectors, installed in the rear bumper (depending on the vehi- cle), measure the distance between the vehicle and an obstacle whilst revers- ing. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 30 centi-...
  • Page 117 PARkING DISTANCE CoNTRoL (2/2) operating faults Depending on the vehicle, when the system detects an operating fault, the message “check parking distance con- trol” appears on the instrument panel, accompanied by the warning light © and a beep lasting approxi- mately 5 seconds.
  • Page 118: Reversing Camera

    REVERSING CAMERA (1/2) operation Note: make sure that the reversing Note: depending on the vehicle, cer- camera is not obscured (by dirt, mud, tain settings can be adjusted from the 2 Moving into reverse gear, the 1 camera snow, etc.). touchscreen.
  • Page 119 REVERSING CAMERA (2/2) This gauge remains fixed and indicates the vehicle trajectory if the wheels are in line with the vehicle. This system is initially used with the aid of several gauges (mobile for trajectory and fixed for distance). When the red zone is reached, use the bumper image to stop accurately.
  • Page 120 2.36...
  • Page 121: Your Comfort

    Section 3: Your comfort Air vents............... Manual air conditioning/heating system .
  • Page 122: Air Vents

    air vents, air outlets (1/2) 1 left-hand side window demister 5 right-hand side air vent. vent. 6 right-hand side window demister 2 left-hand side air vent. outlet. 3 windscreen demisting vents. 7 passenger footwell heater outlets. 4 centre air vents. 8 control panel.
  • Page 123 air vents, air outlets (2/2) To remove bad odours from your ve- hicles, only use the systems designed for this purpose. Consult an approved Dealer. Centre air vents. side air vents air flow air flow Move the control knob 9 (beyond the To open air vent 11, press on the air resistance point).
  • Page 124: Manual Air Conditioning/Heating System

    Manual air ConDitioning (1/3) the controls switching air conditioning on or off 1 Adjusting the air temperature. (depending on vehicle) 2 Adjusting the ventilation speed. The air conditioning is switched on (in- 3 Air conditioning. dicator light on) or off (indicator light off) using button 3.
  • Page 125: Passenger Compartment

    Manual air ConDitioning (2/3) Distribution of air in the passenger compartment There are five air distribution options. Turn control 4 to choose the distribution option. The air flow is directed to the windscreen and the front side window demisting vents. The air flow is distributed be- tween all the air vents, the front side window demisting vents, the...
  • Page 126 Manual air ConDitioning (3/3) adjusting the air temperature Turn control 1 to obtain the desired temperature. The further towards the red the slide is, the higher the tempera- ture will be. When the air conditioning system is used for long periods, it may begin to feel cold.
  • Page 127: Automatic Climate Control

    autoMatiC CliMate Control (1/4) varying the ventilation speed In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. You can still adjust the ventilation speed by turning control 6 to increase or reduce the ventilation speed.
  • Page 128 autoMatiC CliMate Control (2/4) Clear view function Press button 3 – the integrated indica- tor light comes on. This function quickly demists and de- ices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-ic- ing functions must be activated.
  • Page 129 autoMatiC CliMate Control (3/4) rear screen de-icing/ switching air conditioning on demisting or off Press button 8 – the integrated indica- In automatic mode, the system switches tor light comes on. This function en- the air conditioning system on or off, ables rapid demisting or de-icing of the depending on the climate conditions.
  • Page 130 autoMatiC CliMate Control (4/4) Manual use Press button 7 – the integrated indica- tor light comes on. Prolonged use of this position may lead to odours, caused by non-renewal of air, and the formation of condensation on the windows. We therefore advise you to return to au- tomatic mode as soon as air recircula- tion is no longer needed, by pressing button 7.
  • Page 131: Air Conditioning: Information And Advice On Use

    air ConDitioning: information and advice on use advice on use Fuel consumption operating faults In some situations, (air conditioning You will normally notice an increase in As a general rule, contact your ap- off, air recirculation activated, ventila- fuel consumption (especially in town) proved dealer in the event of an oper- tion speed at zero or low, etc.) you may when the air conditioning is operating.
  • Page 132: Electric Windows

    4. A confirmation message is displayed on the instrument panel. Driver’s responsibility Never leave your vehicle with the RENAULT card inside and never leave a child (or a pet) unsuper- vised, even for a short while. They electric windows...
  • Page 133 eleCtriC WinDoWs (2/2) one-touch mode operating faults Depending on the vehicle, this mode In case of a fault when closing a window, works in addition to the operation of the the system reverts to normal mode: electric windows described previously. pull the switch concerned up as often It is only fitted to the driver’s window.
  • Page 134 FixeD sunrooF/sun visor Fixed sunroof blind Front sun visor – opening: push handle 1 upwards, Lower sun visor 2. then guide it until it opens fully; – Closing: pull the handle 1 until it Courtesy mirrors clicks into the catch. Slide cover 3.
  • Page 135: Interior Lighting

    interior ligHting Courtesy light luggage compartment light 4 Press switch 2 for: Light 4 comes on when the boot is opened. – permanent lighting; – intermittent lighting, which comes on when a door is opened. It only switches off after a time delay and when the doors concerned have been closed correctly;...
  • Page 136 Passenger CoMPartMent storage, Fittings (1/4) Front door storage pockets 1 sun visor storage 2 Centre console storage compartment 3 They can hold a 1.5 litre bottle. This can be used for storing motorway tickets, cards, etc. Nothing should be placed Ensure that no hard, heavy on the floor area in front of or pointed objects are...
  • Page 137 Passenger CoMPartMent storage, Fittings (2/4) Passenger storage armrest storage storage compartment 7 compartment 4 compartment Cup holders 8 With the armrest in its lowered position, Passenger storage press button 6 and lift armrest cover. This can be used for storing a mobile compartment 5 ashtray, cup holder, etc.
  • Page 138 Passenger CoMPartMent storage, Fittings (3/4) rear centre console storage Front seat storage pockets 10 compartment 9 This can be used for storing a mobile ashtray, cup holder, etc. When turning corners, accelerating or braking, ensure that the recepta- cle being held by the cup holder is not dislodged.
  • Page 139 Passenger CoMPartMent storage, Fittings (4/4) rear door storage grab handle 12 compartment 11 This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle. Ensure that no hard, heavy or pointed objects are placed in the “open”...
  • Page 140: Ashtray/Cigarette Lighter

    asHtray, Cigarette ligHter, aCCessories soCket accessories socket 1 It is provided for connecting acces- sories approved by our Technical Department with a maximum power of 120 Watts (12V). Cigarette lighter 1 ashtray With the ignition on, push in the ciga- It can be housed in either position 2 rette lighter 1.
  • Page 141 rear HeaD rests Position for use to raise the headrest Raise the headrest as far as possible to Raise the headrest as far as it will go, use it in the high position. Check that it then press button A and remove the is correctly locked.
  • Page 142: Rear Bench Seat: Functions

    rear BenCH seat: functions to replace the seatback, proceed in the reverse order to removal. Refit the seatback and click it back into place. When moving the rear seats, ensure that nothing obstructs the anchorage points (passenger’s arm or to fold down the seatback leg, a pet, gravel, cloth, toys, etc.).
  • Page 143 Boot to open opening the doors manually from the inside Press button 1 and lift the tailgate. If it is impossible to unlock the tailgate, it can be done manually from inside: to close – access the luggage compartment by Lower the tailgate using the handles 2 tilting the rear bench seatback(s), inside the tailgate to help you.
  • Page 144: Rear Parcel Shelf

    rear ParCel sHelF removal utility version – push the shelf in and turn; – pull the shelf towards you. – Lower the rear headrests; Unclip mountings 2 on either side of the parcel shelf, then remove it via the boot. To refit, proceed in the reverse order to –...
  • Page 145: Compartment Cover

    luggage CoMPartMent Cover: estate version to remove the flexible removing the luggage luggage compartment cover section of the luggage compartment cover storage 1 compartment cover 1 Using the handle 2, push the luggage Lift the mobile floor (please refer to the cover to the right (movement A) and lift information on “Boot storage space and Pull handle 2 gently to release the pins...
  • Page 146 Boot arrangeMents Mobile floor Movable floor storage removing the mobile floor – Lower section 1 onto section 2; – Lower section 1 onto section 2; When fitted to the vehicle, it can be used to make loading easier. – lift the assembly and position it –...
  • Page 147 transPorting oBJeCts in tHe luggage CoMPartMent Always position the objects transported so that the largest surface is against: – The rear bench seatback for normal loads (example A). – The front seatbacks with the rear seatbacks folded down, as is the case for maximum loads (example B).
  • Page 148: Transporting Objects

    transPorting oBJeCts towbar A: 697 mm (5-door version). A: 697 mm (Utility version). A: 948 mm (Estate version). Permissible nose weight, maxi- mum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. For fitting and conditions of use, If the towbar ball obscures the regis- refer to the equipment’s fitting in- tration plate or the rear fog lights, it...
  • Page 149: Luggage Net

    transPorting oBJeCts: luggage net (1/2) luggage net A Fitting the luggage net – to access the lower net ring 2 the first time you use it, please contact behind the front seats On equipped vehicles, this can be used an authorised dealer; when transporting animals or luggage, Inside the vehicle on each side: –...
  • Page 150 transPorting oBJeCts: luggage net (2/2) Fitting the luggage net Marking – in the boot, it is essential to attach the hook of the lower mounting strap behind the rear bench seat A marking on the boot floor indicates of the net to the anchoring hook 5 the location of the seat rings ISOFIX 6 Inside the vehicle on each side: identified by the marking 7 (if fitted...
  • Page 151: Roof Bars

    rooF Bars/sPoiler Precautions during use Handling the tailgate Before handling the tailgate, check the objects and/or accessories (bike rack, roof box, etc.) fitted to the roof bars: these must be correctly positioned and secured, so as not to hinder the opera- tion of the tailgate.
  • Page 152: Multimedia Equipment

    MultiMeDia equiPMent The presence and location of this equip- ment depends on the vehicle version. 1 Multimedia touch-screen; 2 Multimedia sockets; 3 Steering column control; 4 Voice commands; 5 Microphone. To use this equipment, consult the instructions for the equipment which should be kept with the other vehi- cle documentation.
  • Page 153 Section 4: Maintenance Bonnet ............... . Engine oil level: general information .
  • Page 154: Bonnet

    BONNET Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and lower it to 30 cm above the closed position, then release it. It will latch automatically under its own weight.
  • Page 155: Engine Oil Level: General Information

    ENGINE OIL LEVEL: general information It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level be- In order to prevent splashback, it is tween oil changes. recommended that a funnel be used when topping up/filling with oil However, contact your approved...
  • Page 156: Engine Oil Level: Topping Up/Filling

    ENGINE OIL LEVEL: topping up/filling (1/2) Topping up/filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on the dipstick 2 (for instance, before the engine is is between 1.5 and 2 litres, depend-...
  • Page 157: Engine Oil Change

    ENGINE OIL LEVEL: topping up, filling OIL ChANGE (2/2) Engine oil grade Refer to the Maintenance Service Booklet for your vehicle. Filling: take care when topping up the oil that no oil drips onto engine components - risk of fire. Remember to refit the cap securely as there is a risk of fire if oil splashes Consult your approved dealer at...
  • Page 158: Levels

    LEVELS (1/3) Frequency of checking coolant level Replacement interval Check the coolant level regularly Refer to the Maintenance Document for (very severe damage is likely to be your vehicle. caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...
  • Page 159: Brake Fluid Level

    LEVELS (2/3) Level 2 It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MINI" warn- ing line. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking pro- cedure from the manufacturer’s net- work or web site.
  • Page 160: Windscreen Washer Reservoir

    LEVELS /FILTERS (3/3) Filters The replacement of filter components (air filter, cabin filter, diesel filter, etc.) is scheduled in the maintenance opera- tions for your vehicle. Replacement intervals for filter el- ements: refer to the Maintenance Document for your vehicle. Windscreen washer reservoir Topping up With the engine switched off, open the...
  • Page 161: Tyre Pressure

    TyRE pRESSURE E: front tyre pressure. F: rear tyre pressure. G: tyre pressure for the emergency spare wheel. Special note concerning fully laden vehicles (Maximum Permissible All-Up Weight) and towing a trailer: the maxi- mum speed must be limited to 60 mph (100 kph) and the tyre pressure in- creased by 0.2 bar.
  • Page 162: Battery

    BATTERy Replacing the battery As this operation is complex, we advise you to contact an approved Dealer. This is located under cover 1 and does Label A not need to be serviced. Observe the indications on the battery: – 2 naked flames and smoking are for- bidden;...
  • Page 163: Bodywork Maintenance

    BODyWORk MAINTENANCE (1/2) What you should not do you should A well-maintained vehicle will last longer. It is therefore recommended to Do not degrease or clean mechani- Wash your car frequently, with the maintain the exterior of the vehicle reg- cal components (e.g.
  • Page 164 BODyWORk MAINTENANCE (2/2) Vehicles with a matte paint Using a roller type car wash Respect local regulations about wash- ing vehicles (e.g. do not wash your ve- finish Return the windscreen wiper stalk to hicle on a public highway). the Park position (refer to the informa- This type of paint requires certain pre- Observe the vehicle stopping distances tion on the “Windscreen washer, wiper”...
  • Page 165: Interior Trim Maintenance

    INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g. instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display, radio display, etc.) larly.
  • Page 166 INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable you should not: equipment originally fitted in You are strongly advised not to po- the vehicle sition objects such as deodorants, scents, etc. near air vents, as this could If you need to remove equipment in damage your dashboard trim.
  • Page 167: Practical Advice

    RENAULT card: battery ........
  • Page 168: Puncture, Emergency Spare Wheel

    PUNCTURE, EMERGENCY SPARE WHEEL (1/4) In case of puncture Depending on the vehicle, a tyre infla- tion kit or emergency spare wheel is provided (refer to the following pages). If the emergency spare wheel has been stored for several years, have it checked by your Dealer to ensure that it is safe to use.
  • Page 169: Emergency Spare Wheel

    PUNCTURE, EMERGENCY SPARE WHEEL (2/4) Emergency spare wheel – unscrew nut 3 in an anti-clockwise – pull the wheel towards you; direction until it comes off com- – lay the wheel down flat and unfasten – Open the tailgate; pletely, then place the palm of your cable 5 from its housing 6.
  • Page 170 PUNCTURE, EMERGENCY SPARE WHEEL (3/4) To refit a wheel To carry out this operation, the cable After changing a wheel, position the must be unwound. replaced wheel on support 7, with the valve facing the ground. Clip cable 5 If the cable has been wound back up on in its housing 6, then push the wheel its own, unwind it again as follows: Do not refit a wheel with an alloy...
  • Page 171: Special Features

    PUNCTURE, EMERGENCY SPARE WHEEL (4/4) NB: if the tool kit does not lock in place, check the tightness of nut 3 and the correct positioning of handle 4. Special features The emergency spare wheel holder should always be present when you are driving even when the wheel itself is not present: risk of water entering the ve- hicle.
  • Page 172 TYRE PRESSURE KIT (1/3) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
  • Page 173 TYRE PRESSURE KIT (2/3) With the engine running and the – after a maximum of 15 minutes, stop parking brake applied, inflating and read the pressure (on pressure gauge 5). – unroll the hose from the container; Note: while the container is empty- –...
  • Page 174 TYRE PRESSURE KIT (3/3) Precautions when using the – Affix the driving recommendation label to the dashboard where it can easily be seen by the driver; The kit should not be operated for more – Put the kit away. than 15 consecutive minutes. –...
  • Page 175: Tools

    TOOLS Jack 2 Fold it correctly before refitting it in its housing (ensure that the wheelbrace is correctly positioned). Hubcap tool 3 This tool is used to remove the wheel trims. Wheel bolt guide 4 To finish loosening or starting to tighten the wheel bolts.
  • Page 176: Wheel Trims - Wheel

    WHEEL TRIMS - WHEEL Do not leave the tools un- secured inside the vehicle as they may come loose under braking. After use, Remove the wheel trim using hubcap check that all the tools are correctly tool 1 (located in the tool kit) by en- clipped into the tool kit, then posi- gaging the hook in the opening near tion it correctly in its housing: risk of...
  • Page 177: Changing A Wheel

    CHANGING A WHEEL (1/2) Vehicles equipped with a jack Continue to crank the jack so that the baseplate is correctly positioned (it and wheelbrace should be underneath the vehicle and If necessary, remove the wheel trim. aligned with the jack head). Use the wheelbrace 1 to slacken off the Turn it a few times to lift the wheel off wheel bolts.
  • Page 178 CHANGING A WHEEL (2/2) Undo the bolts and take off the wheel. Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub. Tighten the bolts, checking that the wheel is correctly positioned on its hub.
  • Page 179: Tyres (Tyre And Wheel Safety, Use In Winter)

    TYRES (1/3) Tyre and wheel safety When the tyre tread has been worn to the level of the warning strips, they The tyres are the only contact between become visible 2: it is then neces- the vehicle and the road, so it is essen- sary to replace your tyres because the tial to keep them in good condition.
  • Page 180: Tyre Pressures

    TYRES (2/3) Tyre pressures Emergency spare wheel Pressures should be checked when the tyres are cold; ignore higher pressures Adhere to the tyre pressures (including Refer to the information on the which may be reached in hot weather the emergency spare wheel). The tyre “Emergency spare wheel”...
  • Page 181 TYRES (3/3) Use in winter Snow or Winter tyres Studded tyres We would recommend that these be This type of equipment may only be Chains fitted to all four wheels to ensure that used for a limited period and as laid For safety reasons, fitting snow your vehicle retains maximum adhe- down by local legislation.
  • Page 182: Front Headlights: Changing Bulbs

    FRONT HEADLIGHTS: changing bulbs (1/3) Main beam headlight To change the bulb: – remove cover C; – disconnect wiring 4; – unclip spring 5 and remove the bulb. Bulb type: H1 It is essential to use anti-U.V. 55W bulbs so as not to damage the plastic on the headlights.
  • Page 183 FRONT HEADLIGHTS: changing bulbs (2/3) Front side light To change a bulb, remove cover A. Pull bulb holder 6 to access the bulb. Bulb type: W5W. The engine may be hot when carrying out opera- tions in close proximity. In To comply with local legislation, or The bulbs are under pres- as a precaution, you can obtain an...
  • Page 184 FRONT HEADLIGHTS: changing bulbs (3/3) Additional lights If you wish to fit fog lights to your ve- hicle, please see an authorised dealer. Daytime running lights 7 Please see an authorised dealer. Front fog lights 8 The front bumper needs to be removed; Any operation on (or modi- consult an approved Dealer.
  • Page 185 REAR AND SIDE LIGHTS: changing bulbs (1/4) Five-door version To release the light unit, start by moving Refit the bulb holder and push the unit the exterior edge away to a suffi- in fully until it locks in place. Side lights/brake and direction cient extent (movement A) to release Check that the light is properly locked indicator lights...
  • Page 186 REAR AND SIDE LIGHTS: changing bulbs (2/4) Estate version Remove the bulb holder by carefully re- leasing clips 9, and gently pull the bulb Side lights/brake and direction holder. indicator lights Change the bulb. Unclip the cover to access nut 7. Refit the bulb holder and push the unit Unscrew nut 7.
  • Page 187 REAR AND SIDE LIGHTS: changing bulbs (3/4) Five door and estate versions Unclip cover 13 and remove it. Turn bulb holder 14 fully anticlockwise and change the bulb. Reversing lights and rear fog To reassemble, proceed in the reverse lights 12 order to removal.
  • Page 188: Rear Lights And Side Lights: Changing Bulbs

    REAR LIGHTS AND SIDE LIGHTS: changing bulbs (4/4) High-level brake light 15 Number plate lights 16 Side indicator lights 18 Consult an approved dealer. – Unclip light 16 by pressing tab 17; Consult an approved dealer. – remove the light cover to gain access to the bulb.
  • Page 189: Interior Lighting: Changing Bulbs

    INTERIOR LIGHTING: changing bulbs Courtesy light Luggage compartment light Press tab 3 to release the bulb holder and access bulb 4. Unclip the lens (using a flat-blade Unclip light 2 by pressing the tabs on Bulb type: C5W festoon type bulb. screwdriver or similar).
  • Page 190: Renault Card: Battery

    (insert the the next time the vehicle is started, the replace the RENAULT card battery, RENAULT card in the card reader) and message will disappear. press button 1, pulling on emergency lock/unlock the vehicle (refer to the in- Note: it is not advisable to touch the key 2, then unclip cover 3 using tab 4.
  • Page 191: Fuses

    FUSES (1/5) Fuses in passenger compartment A Clip 1 Fuses in engine compartment B If any electrical component does not Some functions are protected by fuses Remove the fuse using tweezers 1, lo- work, check the condition of the fuses. located in the engine compartment cated at the back of flap A.
  • Page 192 FUSES (2/5) Allocation of fuses diagram C (the presence of certain fuse depends on the vehicle equipment level) 5.26...
  • Page 193 FUSES (3/5) Number Allocation Number Allocation Number Allocation Courtesy light, boot light, Front windscreen wiper Automatic gearbox air-conditioning Front left daytime running Reversing light, rear wiper, light, right side light, left- ABS-ESC, brake switch passenger compartment hand main beam headlight, right-hand dipped beam headlight Empty location...
  • Page 194 FUSES (4/5) Allocation of fuses diagram D (the presence of certain fuse depends on the vehicle equipment level) 5.28...
  • Page 195 FUSES (5/5) Number Allocation Number Allocation Number Allocation Empty location ABS-ESC, brake switch Automatic gearbox Front fog lights Steering column control Reversing light, rear wiper, passenger compartment Wipers Horn Right-hand side lights Rear fog lights Instrument panel Cigarette lighter Left-hand side lights Steering column control, Radio and multimedia, additional equipment...
  • Page 196: Battery

    BATTERY: breakdown recovery (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any electrical consumers The battery charger must be com- (courtesy lights, etc.) are switched patible with a battery with nominal off before disconnecting or recon- voltage of 12 volts.
  • Page 197 BATTERY: breakdown recovery (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.
  • Page 198: Fitting A Radio

    FITTING A RADIO – In all cases, it is very important to follow the manufacturer’s instruc- tions carefully. – The specifications of the brack- Radio location 1 Door speakers 2 ets and wires (available from our network) vary depending on the Unclip the blanking cover.
  • Page 199: Accessories

    ACCESSORIES Electrical and electronic accessories Before installing this type of accessory, make sure it is compatible with your vehicle. You can get advice from an au- thorised dealer. Connect accessories with a maximum power of 120 watts only. Fire hazard. No work may be carried out on the vehicle’s electrical or radio circuits, except by authorised dealers: an incorrectly connected system may result in damage being caused to the electrical equipment and/or the components connected to it.
  • Page 200: Windscreen Wiper Blades

    WINDSCREEN WIPER BLADES (1/2) Check the condition of the wiper blades. You are responsible for their service life: – clean the blades, windscreen and rear screen regularly with soapy water; – do not use them when the wind- screen or rear screen are dry; –...
  • Page 201 WINDSCREEN WIPER BLADES (2/2) To refit To refit the wiper blade, proceed in re- verse order to removal. Make sure that the blade is correctly locked in position. Rear screen wiper blade 5 – In frosty weather, make sure that the wiper blades –...
  • Page 202 If your vehicle is the towing or R for vehicles with automatic gear- vehicle, do not exceed the maximum boxes), insert the RENAULT card in the towing weight for your vehicle (refer card reader, then press the engine start to the information on “Weights”...
  • Page 203 Unclip cover 4 or 6 by sliding a flat tool (never use the drive shafts or any other (or the key integrated in the RENAULT part of the vehicle). card) under the cover. These towing points may only be used...
  • Page 204 Dealer as soon as possible. Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not lock or Card battery is flat. Replace the battery. You can still lock/ unlock the doors. unlock and start your vehicle (refer to the information on “Locking/unlocking the...
  • Page 205: Operating Faults

    Starting conditions are not Refer to the information on “Starting/stopping the fulfilled. engine” in Section 2. The RENAULT “hands-free” Insert the card in the card reader in order to start the card does not work. engine. Refer to the information on “Starting/stopping the engine”...
  • Page 206 OPERATING FAULTS (3/5) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pres- Check the tyre pressures: if this is not the sures, incorrectly balanced or dam- problem, have them checked by an ap- aged. proved Dealer.
  • Page 207 OPERATING FAULTS (4/5) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine is overheating. The cool- Engine cooling fan not working. Stop the vehicle, switch off the engine and ant temperature indicator is in the contact an approved dealer.
  • Page 208 OPERATING FAULTS (5/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse, refer to the information on “Fuses”.
  • Page 209: Technical Specifications

    Section 6: Technical specifications Vehicle identification plate ............Engine identification plate .
  • Page 210: Vehicle Identification Plate

    Vehicle identification plates the information shown on the ve- 4 MAM (Maximum Authorised Mass) hicle identification plate should be for front axle. quoted on all correspondence or 5 GTW (Gross train weight: vehicle orders. fully loaded, with trailer). 6 MPAW (Maximim Permissible the presence and location of the in- Weight) for front axle.
  • Page 211: Engine Identification Plate

    enGine identification plates please quote the information on the engine plate or label A in all corre- spondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
  • Page 212: Dimensions

    dimensions (in metres) (1/2) five-door version 0,853 2,589 0,621 1,509 4,063 1,448 1,512 1,945 * unladen...
  • Page 213 dimensions (in metres) (2/2) estate version 0,853 2,589 0,825 1,509 4,267 1,445 1,512 1,945 * unladen...
  • Page 214: Engine Specifications

    enGine specifications Versions 0.9 tce 1.2 16V 1.2 tce 1.5 dci engine type H4B Turbo H5F Turbo K9K Turbo (see engine plate) cubic capacity (cc) 1149 1 197 1461 type of fuel It is essential that you use It is essential that you use unleaded petrol of Diesel: the label octane rating unleaded petrol of the octane...
  • Page 215: Towing Weights

    WeiGhts (in kg) the weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. consult your approved dealer. Five door Estate maximum permissible all-up weight (mmac) Weights are indicated on the vehicle identification plate (refer to maximum permissible all-up weight (mmta) the information on “Vehicle identification plates”...
  • Page 216: Replacement Parts And Repairs

    Replacement paRts and RepaiRs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
  • Page 217: Service Sheets

    seRVice sheets (1/6) Vin: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........□ anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □...
  • Page 218 seRVice sheets (2/6) Vin: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........□ anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □...
  • Page 219 seRVice sheets (3/6) Vin: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........□ anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □...
  • Page 220 seRVice sheets (4/6) Vin: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........□ anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □...
  • Page 221 seRVice sheets (5/6) Vin: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........□ anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □...
  • Page 222 seRVice sheets (6/6) Vin: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........□ anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □...
  • Page 223: Anticorrosion Check

    anticoRRosion check (1/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.15...
  • Page 224 anticoRRosion check (2/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.16...
  • Page 225 anticoRRosion check (3/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.17...
  • Page 226 anticoRRosion check (4/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.18...
  • Page 227 anticoRRosion check (5/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.19...
  • Page 228 anticoRRosion check (6/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.20...
  • Page 229: Alphabetical Index

    AlphAbeticAl index (1/5) ABS ..............1.50, 2.18 → 2.21 catalytic converter............. 2.9 – 2.10 accessories................ 5.33 central door locking ......1.4 → 1.8, 1.12 → 1.14 accessories socket ............3.20 changing a bulb .............5.16 → 5.23 additional methods of restraint .......... 1.29 changing a wheel............
  • Page 230 AlphAbeticAl index (2/5) driving position front seats settings ............1.19 → 1.22 adjustment ............1.15 → 1.19 fuel advice on fuel economy ..........2.14 electric beam height adjustment ........1.72 filling ............1.48, 1.76 → 1.78 electric windows ............. 3.12 – 3.13 grade ..............1.76 → 1.78 electronic stability control: ESC ......2.18 →...
  • Page 231 AlphAbeticAl index (3/5) indicators: number plate lights ............5.22 direction indicators ............1.71 reversing lights ............. 5.19 instrument panel ..........1.48 → 1.54 side lights ..........1.68, 5.16 → 5.19 instrument panel ............1.48 → 1.63 lights-on warning buzzer............ 1.10 instrument panel messages........1.53 → 1.63 load permitted on the roof............
  • Page 232 ..............3.22 sun visor ................3.14 rear view mirrors ..............1.67 switching on the vehicle ignition ........2.3 → 2.5 RENAULT ANTI-INTRUDER DEVICE (RAID) ....1.14 RENAULT card tailgate ............3.23, 3.26 – 3.27 battery ................5.24 tanks and reservoirs use .............
  • Page 233 AlphAbeticAl index (5/5) tyre pressures ..............4.9 tyres ..............4.9, 5.13 → 5.15 unlocking the doors ..........1.12 – 1.13 variable power-assisted steering ........1.64 vehicle identification plates ..........6.3 ventilation ..............3.2 → 3.11 warning lights............1.48 → 1.63 washing ..............4.11 – 4.12 weights ................
  • Page 235 à999107769Rò î í ä RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60 NU 955-2 –...

Table of Contents