Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
In This Chapter
In This Chapter
Overview
About the Vanguard 100
This chapter describes the features and pre-installation activities appropriate to
Vanguard 100 devices.
Topic
Features .........................................................................................................
Memory DRAM Recovery ...........................................................................
Pre-Installation Procedures ...........................................................................
Unpacking ................................................................................................
and Requirements for DSU ...................................................................... 1-10
The Motorola Vanguard 100 Frame Relay Access Device (FRAD) connects serial
devices to a Frame Relay network. This FLASH-based Vanguard is available either
with or without an integral DSU daughtercard, DIM Site daughtercard, ISDN
daughtercard, or Voice daughtercard, in a desktop-size standalone enclosure, as
shown in Figure 1-1.
Figure 1-1. Motorola Vanguard 100
The Vanguard 100 can be ordered in mono FRAD or duo FRAD configurations with
either two or three serial ports, respectively.
You can use the optional second port for dial backup or as a second user port,
permitting two applications with different protocols share the same Frame Relay
circuit.
Chapter 1
About the Vanguard 100
See Page
1-3
1-5
1-6
1-8
1-1
Advertisement
Related Manuals for Motorola 68436 - Vanguard 100I - Remote Access Server
Summary of Contents for Motorola 68436 - Vanguard 100I - Remote Access Server
-
Page 1: Table Of Contents
Requirements for DSU ..............1-10 Overview The Motorola Vanguard 100 Frame Relay Access Device (FRAD) connects serial devices to a Frame Relay network. This FLASH-based Vanguard is available either with or without an integral DSU daughtercard, DIM Site daughtercard, ISDN daughtercard, or Voice daughtercard, in a desktop-size standalone enclosure, as shown in Figure 1-1. - Page 2 This Offers... Configuration... mono FRAD DIM Port orderable as V.24, V.35, V.36, or V.11 V.24 interface mono FRAD with V.24 interface DSU daughtercard interface duo FRAD DIM Port orderable as V.24, V.35, V.36, or V.11 DIM Site daughtercard interface V.24 interface duo FRAD with DIM Port orderable as V.24, V.35, V.36, or V.11 V.24 interface...
-
Page 3: Features
Diagnostic loopbacks from the telephone company are supported. You activate local diagnostics from the Control Terminal Port (CTP). CTP Manageability You can manage the Motorola Vanguard 100 from the CTP for configuration, reporting, and troubleshooting. Vanguard 100 is available in two and three serial port versions. Ports have the following characteristics. - Page 4 Features Memory The board contains 1 Mbyte of FLASH memory and 2 Mbytes of DRAM. Default Report Log On software releases prior to 4.35, 140 data buffers were allocated for reports, for a Size total of 200 reports. For the 4.35 software, 10 data buffers are allocated for reports, for a total of 20 reports that can be logged on the Vanguard 100, thereby saving 130 data buffers.
-
Page 5: Memory Dram Recovery
Memory DRAM Recovery Memory DRAM Recovery Introduction On software prior to Release 4.35, 65 kilobytes was allocated for configuration memory size internally, which is identical to the allotment for the 6525. For the Vanguard 100, 65 kilobytes is unnecessary, since configuration memory size is only 8 kilobytes. -
Page 6: Pre-Installation Procedures
Power Source Choose a site that is within an appropriate distance of a power source. Depending on your application and the country in which you operate the Motorola Vanguard 100, this must be a grounded 100 to 240 VAC outlet. - Page 7 Pre-Installation Procedures Cable Clearance/ Allow at least 12 inches (30.5 cm) in back of the unit for air circulation and interface Air Circulation cable clearance. Refer to Figure 1-2. Caution To avoid overheating the unit’s circuitry, never place anything: • On top of the unit, •...
-
Page 8: Unpacking
Vanguard 100 components are factory installed in the base unit. In addition to the Your Vanguard 100 base unit and accompanying components, the shipping carton may include a sleeve containing the power cord. Upon receipt of the Motorola Vanguard 100, check the contents of the shipping container as follows. Step Action Check the shipping carton and its contents for damage. - Page 9 Pre-Installation Procedures In Case of Damage If the equipment is damaged in transit, contact the shipper. If you have additional concerns in case of failure, about missing parts, or to return equipment, contact your nearest Motorola ISG representative. For Locations... Contact...
-
Page 10: Fcc Part 68 And Telephone Company Procedures And Requirements For Dsu
FCC Part 68 and Telephone Company Procedures and Requirements for DSU Before You Begin Before the Motorola Vanguard 100 can be connected to the network, you must: • Provide the local telephone company with the equipment’s registration number • Order the proper connections...