Fujitsu LifeBook B6230 notebook User Manual
  1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Laptop
  5. Fujitsu LifeBook B6230 notebook
  6. User manual
Fujitsu LifeBook B6230 notebook User Manual

Fujitsu LifeBook B6230 notebook User Manual

Fujitsu computer systems corporation user guide
Hide thumbs Also See for Fujitsu LifeBook B6230 notebook:
Table of Contents

Advertisement

Quick Links

Download this manual
User's Guide
Learn how to use
your Fujitsu LifeBook
B6230 notebook

Advertisement

Table of Contents
loading

Related Manuals for Fujitsu Fujitsu LifeBook B6230 notebook

Summary of Contents for Fujitsu Fujitsu LifeBook B6230 notebook

  • Page 1 User’s Guide Learn how to use your Fujitsu LifeBook B6230 notebook...
  • Page 2 Copyright and Trademark Information Fujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document.
  • Page 3 ANDLING THE CORD ON THIS PRODUCT WILL EXPOSE YOU TO LEAD TATE OF ALIFORNIA TO CAUSE BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM ASH HANDS AFTER HANDLING © Copyright 2008 Fujitsu Computer Systems Corporation. All rights reserved. No part of this publication may be copied, reproduced, or translated, without prior written consent of Fujitsu. No part of this publication may be stored or transmitted in any electronic form without the written consent of Fujitsu.
  • Page 4 This unit requires an AC adapter to operate. Use only UL Listed I.T.E. Class II Adapters with an output rating of 16 VDC, with a current of 3.75 A. AC adapter output polarity: When using your notebook equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: •...

  • Page 5: Recycling Your Battery

    System Disposal INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL Recycling your battery Over time, the batteries that run your mobile computer will begin to hold a charge for a shorter amount of time; this is a natural occurrence for all batteries.

  • Page 6: Table Of Contents

    Contents Preface About This Guide ..........8 Conventions Used in the Guide .
  • Page 7 Wireless LAN/Bluetooth Device Access Indicator ....23 Hard Drive or Removable Drive Access Indicator ....23 PC Card Access Indicator .
  • Page 8 Power Sources ..........46 Connecting the Power Adapters .
  • Page 9 Lithium ion Battery..........63 Recharging the Batteries.
  • Page 10 Troubleshooting..........80 Identifying the Problem .
  • Page 11 Audio ........... . . 114 Mass Storage Device Options.
  • Page 12 Configuring the WLAN Using Windows Vista ..... 152 Configuring the WLAN Using Windows XP ..... . 153 Connection to the network .

  • Page 13: Preface

    Preface About This Guide The LifeBook B6230 notebook from Fujitsu Computer Systems Corporation provides desktop performance with a fast Intel® Core™2 Duo ultra-low voltage processor, has a built-in 12.1" color touch screen display, and brings the computing power of a desktop personal computer to a portable environment. This manual explains how to operate your LifeBook notebook’s hardware and built-in system software.

  • Page 14: Fujitsu Contact Information

    HE INFORMATION ICON HIGHLIGHTS INFORMATION THAT WILL ENHANCE YOUR UNDERSTANDING OF THE SUBJECT MATERIAL HE CAUTION ICON HIGHLIGHTS INFORMATION THAT IS IMPORTANT TO THE SAFE OPERATION OF YOUR COMPUTER OR TO THE INTEGRITY OF YOUR FILES CAREFULLY HE WARNING ICON HIGHLIGHTS INFORMATION THAT CAN BE HAZARDOUS TO EITHER YOU OOK NOTEBOOK Fujitsu Contact Information Service and Support...
  • Page 15 • Conditions under which the problem occurred • Any error messages that have occurred • Type of device connected, if any Fujitsu Shopping Online You can go directly to the online by going to the website at: www.shopfujitsu.com. OU MUST HAVE AN ACTIVE INTERNET CONNECTION TO USE THE ONLINE Limited Warranty Your LifeBook notebook is backed by a Fujitsu International Limited Warranty.

  • Page 16: Getting To Know Your Lifebook

    Getting to Know Your LifeBook Overview This section describes the components of your Fujitsu LifeBook B6230 notebook. We strongly recommend that you read it before using your notebook – even if you are already familiar with notebook computers. Figure 1. Fujitsu LifeBook B6230 notebook...

  • Page 17: Locating The Controls And Connectors

    Locating the Controls and Connectors Scroll Button/Fingerprint Recognition Sensor Touchpad Pointing Device Keyboard Figure 2. LifeBook notebook with display open 12 - Locating the Controls and Connectors Display Panel Latch Touch Screen Display Panel Status Indicator Panel LifeBook Security Application Panel Suspend/ Resume Button Stereo Speakers...

  • Page 18: Top Components

    Top Components The following is a brief description of your LifeBook notebook’s top components. Display Panel Latch The display panel latch is used to latch and unlatch the display. See “Opening the Display Panel” on page 48. Touch Screen Display Panel The display panel is a color LCD panel with back lighting for the display of text and graphics and touch screen functionality.
  • Page 19 Pen Garage The pen garage is used to store the system stylus when not in use. Keyboard A full-size keyboard with dedicated Windows keys. See “Keyboard” on page 25. Touchpad Pointing Device The Touchpad pointing device consists of two mouse-like buttons, a scroll button, and a cursor control pad.

  • Page 20: Left-Side Panel Components

    DC Power Jack Headphone/Line-Out Jack Microphone/Line-In Jack Figure 3. LifeBook notebook left-side panel Left-Side Panel Components The following is a brief description of your LifeBook notebook’s left-side components. Modem (RJ-11) Telephone Jack The Modem (RJ-11) telephone jack is for attaching a telephone line to the internal multinational 56K modem.
  • Page 21 HE INTERNAL MULTINATIONAL MODEM IS DESIGNED TO THE MAXIMUM SPEED OF RATE DEPENDS ON THE LINE CONDITIONS ACCORDANCE WITH OR ADDITIONAL INFORMATION ABOUT THE MODEM FUJITSU COMPUTERS PC Card Eject Button The PC Card Eject Button assists you in removing a PC Card from the PC Card slot. PC Card Slot The PC Card Slot allows you to install a Type I or Type II PC Card.

  • Page 22: Right-Side Panel Components

    CompactFlash Card Eject Button Stylus USB 2.0 Ports Anti-Theft Lock Slot CompactFlash Card Slot Figure 4. LifeBook notebook right-side panel Right-Side Panel Components The following is a brief description of your LifeBook notebook’s right-side components. Stylus The stylus is used as the pointing device for the touch screen. CompactFlash Card Eject Button Allows you to eject a CompactFlash card.

  • Page 23: Back Panel Components

    External Video Port Wireless LAN/Bluetooth On/Off Switch Gigabit LAN (RJ-45) Jack Figure 5. LifeBook notebook back panel Back Panel Components Following is a brief description of your LifeBook notebook’s back panel components. External Video Port The external monitor port allows you to connect an external monitor or LCD projector. See “External Video Port”...

  • Page 24: Bottom Components

    Main Unit and Configuration Label (approximate location) Battery Pack Latches Figure 6. LifeBook notebook bottom panel Bottom Components The following is a brief description of your LifeBook notebook’s bottom panel components. Docking Port Connector This connector allows you to connect the optional Port Replicator. Air Vents The air vents allow air to circulate through the system to cool down the components.
  • Page 25 O PROTECT YOUR NOTEBOOK FROM DAMAGE AND TO OPTIMIZE PERFORMANCE ALL AIR ALL VENTS UNOBSTRUCTED CLEANING DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED O NOT OPERATE THE NOTEBOOK IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED TIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION Memory Upgrade Compartment Your notebook comes with high speed Double Data Rate 2 Synchronous Dynamic RAM (DDR2...

  • Page 26: Status Indicator Panel

    AC Adapter Power Status Indicator Panel The Status Indicator displays symbols that correspond with a specific component of your LifeBook notebook. These symbols tell you how each of those components are operating. Power Indicator The Power indicator symbol states whether your system is operational. It has several different states, each of which tells you what mode your notebook is in at that time.

  • Page 27: Ac Adapter Indicator

    • Steady On: This means that there is power to your notebook and that it is ready for use. • Flashing: This means that your notebook is in Sleep mode. • Steady Off: This means that your system is either in Hibernate mode, or it has been turned off. If you are charging your battery, the Power indicator symbol will remain on even if your LifeBook notebook is shut off.

  • Page 28: Battery Charging Indicator

    • SHORTED BATTERY IS DAMAGED AND MUST BE REPLACED • ATTERIES SUBJECTED TO SHOCKS DAMAGED F THERE IS NO BATTERY ACTIVITY ATTERY Battery Charging Indicator Located to the left of the Battery Level indicator is a small arrow symbol. This symbol states whether the battery is charging.

  • Page 29: Compactflash (Cf) Card Access Indicator

    CompactFlash (CF) Card Access Indicator The CompactFlash Card Access indicator states whether or not your notebook is accessing a CompactFlash Card. The indicator will flash if your software tries to access a CompactFlash Card even if there is no card inserted. See “CompactFlash Cards” on page 70. NumLk Indicator The NumLk indicator states that the integral keyboard is set in ten-key numeric keypad mode.

  • Page 30: Keyboard

    Keyboard Fn Key Start Key Using the Keyboard Your LifeBook notebook has an integral 82-key keyboard. The keys perform all the standard functions of a 101-key keyboard, including the Windows keys and other special function keys. This section describes the following keys. •...
  • Page 31 the right, left, up, or down within windows, applications and documents. • Function keys: The keys labeled [F1] through [F12], are used in conjunction with the [Fn] key to produce special actions that vary depending on what program is running. Windows keys: These keys work with your Windows operating system and function the same as the onscreen Start menu button, or the right button on your pointing device.
  • Page 32 Function Keys Your LifeBook notebook has 12 function keys, F1 through F12. The functions assigned to these keys differ for each application. You should refer to your software documentation to find out how these keys are used. [Fn] Key The [Fn] key provides extended functions for the notebook and is always used in conjunction with another key.

  • Page 33: Touchpad Pointing Device

    Touchpad Pointing Device Cursor Control Left Button Scroll button or optional Fingerprint Recognition Sensor The Touchpad pointing device comes built into your Fujitsu LifeBook notebook. It is used to control the movement of the pointer to select items on your display panel. The Touchpad is composed of a cursor control, a left button, a right button, and a scroll button (or fingerprint sensor, depending upon your system configuration).

  • Page 34: Clicking

    Clicking means pushing and releasing a button. To left-click, move the cursor to the item you wish to select, press the left button once, and then immediately release it. You can also perform the clicking operation by tapping lightly on the Touchpad once. To right- click, move the mouse cursor to the item you wish to select, press the right button once, then immediately release it.

  • Page 35: Dragging

    Dragging means pressing and holding the left button, while moving the cursor. To drag, move the cursor to the item you wish to move. Press and hold the left button while moving the item to its new location and then release it. Dragging can also be done using the Touchpad.

  • Page 36: Touch Screen

    Touch Screen The integrated touch screen allows you to use either the included stylus, or your fingertip, as a pointing device. You can use the stylus to click, double-click, drag items and icons, or to draw like a pen or pencil in applications that support this behavior, such as drawing or painting programs.

  • Page 37: Clicking

    O AVOID POTENTIAL SCRATCHING AND DAMAGE YOUR FINGER WITH THE TOUCH SCREEN O PURCHASE ADDITIONAL OR REPLACEMENT STYLUSES SHOPFUJITSU Clicking To left-click, touch the object you wish to select, then lift the stylus tip immediately. You also have the option to perform the left-click operation by tapping lightly with your finger on the touch screen once.

  • Page 38: Double-Clicking

    Double-Clicking To double-click on the touch screen, touch the item twice, and then immediately remove the stylus tip. You also have the option to perform the double-click operation by tapping lightly with your finger on the touch screen twice. Note that if the interval between taps is too long, the double-click will not be executed.

  • Page 39: Calibrating The Touch Screen

    In order to ensure accurate tracking between the stylus and cursor, you should run the Touch Screen Calibration Utility before you use the touch screen for the first time, or after you change the display resolution. Depending upon your operating system, the steps vary slightly, as noted below: Microsoft Windows XP Professional Edition To run the calibration utility: Go to [Start] ->...

  • Page 40: Volume Control

    Volume Control Your Fujitsu LifeBook notebook has multiple volume controls which interact with each other. NY SOFTWARE THAT CONTAINS AUDIO FILES WILL ALSO CONTAIN A VOLUME CONTROL OF ITS OWN YOU INSTALL AN EXTERNAL AUDIO DEVICE THAT HAS AN INDEPENDENT VOLUME CONTROL HARDWARE VOLUME CONTROL AND THE SOFTWARE VOLUME CONTROL WILL INTERACT WITH EACH OTHER THE EXTERNAL VOLUME CONTROL SETTING...

  • Page 41: Lifebook Security/Application Panel

    LifeBook Security/Application Panel A unique feature of your LifeBook notebook is the Security/Application Panel that allows you to secure your notebook from unauthorized use. The Security/Application Panel also allows you to launch applications with the touch of a button when your system is on. If the security system is activated, upon starting your notebook or resuming from Standby mode the security system requires you to enter a password code using the buttons on the Security/Application Panel.

  • Page 42: Setting Up Your Security Panel

    Setting up Your Security Panel When you receive your LifeBook notebook, the security panel application is pre-installed without any passwords. The following sections provide detailed information on your security panel, how to set, change or remove passwords. Numbered Buttons Use these buttons to enter your password. Enter Button After entering the button strokes, push this button to enter the password into the LifeBook notebook.
  • Page 43 Setting Passwords When shipped from the factory, no passwords are set. You have a choice of having no password or setting a supervisor and user password. You must set the supervisor password before the user password. • HE PURPOSE OF SUPERVISOR PASSWORD IS TO BE ABLE TO BYPASS THE USER PASSWORD IN CASE THE USER PASSWORD IS FORGOTTEN •...
  • Page 44 Microsoft Windows XP Tablet PC Edition Pre-Boot Pre-logon (Windows logon /Icon Security Button Button Function Function Security Button 1 Security Button 2 Security Screen Rotation Screen Rotation Screen Rotation Display Switching Button 3 Security Secondary Button 4 Function Selection Security Enter [Ctl]+[Alt]+[Del] Enter Button]...
  • Page 45 Setting Supervisor Password You must have set a supervisor password before setting any user passwords. The supervisor password can bypass the user password. Depending upon your operating system, use the appropriate procedure below. Windows XP: Go to the Start menu. Click on Run.

  • Page 46: Operating Your Lifebook Security/ Application Panel

    Go to the Start menu. Select All Programs. Select Security Panel Application and Set User Password. Follow instructions to set the user password. OU MAY CHANGE OR REMOVE THE SUPERVISOR OR USER PASSWORD BY REPEATING THE STEPS DEFINED ABOVE Operating Your LifeBook Security/ Application Panel The security lock feature is in effect both when the system resumes from Off or Standby state.

  • Page 47: Precautions

    Incorrect Password Entry If an invalid supervisor or user password is entered three times in succession, the system will “beep” for about one minute. If a valid password is entered within a minute (while system beeps), the beeping will stop and the notebook will resume normal operation. If no or an invalid password is entered while the system beeps, the system will return to its previous locked state (standby or off) and the Security Indicator will go off.
  • Page 48 Uninstalling the Security Panel Software Remove passwords when User wants no password protection whatsoever and doesn’t want to give anybody the utility to set a password on their computer. In this case, if passwords (supervisor, user, or both) are set, the passwords must first be cleared before removing the application. To clear passwords, follow same procedure in “Setting Passwords”...
  • Page 49 Reinstalling the Security/Application Panel To reinstall supervisor or user security application, you will need your Drivers and Applications CD. The Utilities/Security Application Panel folder contains two separate folders: Supervisor and User. The setup files for supervisor and user security applications are contained in those folders. Go to the Utilities/Security Application Pane/Supervisor folder on the CD and double-click the setupS.exe file.

  • Page 50: Launching Applications With The Lifebook Application Panel

    When you start Windows, the LifeBook Application Panel is automatically activated. As an application launcher, the LifeBook Application Panel is very flexible, giving you a variety of options. An icon resembling a finger pressing a button will appear on the system tray (the indented portion of the status bar where the clock is displayed).

  • Page 51: Power Sources

    Chapter 2 Getting Started with Your LifeBook DC Power Jack AC Cable DC Output Cable AC Adapter Figure 20. Connecting the AC Adapter Power Sources Your Fujitsu LifeBook notebook has three possible power sources: a primary Lithium ion battery, an AC adapter or an optional Auto/Airline adapter.

  • Page 52: Connecting The Power Adapters

    The AC adapter or optional Auto/Airline adapter provides power for operating your notebook and charging the batteries. Connecting the AC Adapter Plug the DC output cable into the DC power jack of your LifeBook notebook. Plug the AC adapter into an AC electrical outlet. Connecting the Optional Auto/Airline Adapter Plug the DC output cable into the DC power jack on your notebook.

  • Page 53: Display Panel

    Display Panel Latch Button Display Panel Your Fujitsu LifeBook notebook contains a display panel that is backlit for easier viewing in bright environments and maintains top resolution through the use of active-matrix technology. Opening the Display Panel Press the Display Panel latch button in. This releases the locking mechanism, allowing you to raise the display. Lift the display backwards, being careful not to touch the screen, until it is at a comfortable viewing angle.

  • Page 54: Using The Keyboard

    OTE THAT WHEN YOU CHANGE THE DISPLAY SETTINGS IN WILL BE RETAINED AFTER STANDBY AND RESTART SETTINGS ARE TEMPORARY BY DEFAULT PTIONS UTILITY IN THE Using the Keyboard • [Fn+F6]: Pressing repeatedly will lower the brightness of your display. • [Fn+F7]: Pressing repeatedly will increase the brightness of the display. Using the Power Options (Windows Vista) To change the brightness using the Power Options utility, open the Control Panel and double-click on the Power Options icon.

  • Page 55: Starting Your Lifebook Notebook

    Starting Your LifeBook Notebook Power On Suspend/Resume Button The Suspend/Resume button is used to turn on your LifeBook notebook from its off state. Once you have connected your AC adapter or charged the internal Lithium ion battery, you can power on your notebook. HEN YOU TURN ON YOUR THAT A BATTERY IS INSTALLED AND CHARGED CONNECTED AND HAS POWER...

  • Page 56: Boot Sequence

    O NOT CARRY YOUR OR VIBRATION AS YOU RISK DAMAGING YOUR NOTEBOOK When you turn on your LifeBook notebook, it will perform a Power On Self Test (POST) to check the internal parts and configuration for correct functionality. If a fault is found, your LifeBook notebook will emit an audio warning and/or an error message will be displayed.

  • Page 57: Hard Disk Drive Passwords

    To provide additional security for your data, you can assign passwords to your hard disk drive(s). This feature is managed in the system BIOS Setup Utility. See BIOS Setup Utility below for information about accessing the utility. EMEMBER YOUR PASSWORDS PASSWORDS UJITSU HAVE TO REPLACE YOUR SYSTEM BOARD OR HARD DISK DRIVE...

  • Page 58: Booting The System

    Using the TrustedCore Menu When the Fujitsu logo appears on the screen. press the [Enter] key or click on the left mouse or touchpad button; the TrustedCore Menu will appear. The TrustedCore Menu provides shortcuts to the following menus and information screens: •...

  • Page 59: Starting Windows Vista The First Time

    HE FIRST TIME YOU INITIALIZE YOUR APPROXIMATELY TWO MINUTES BOX WILL APPEAR MPORTANT URING THE SETUP PROCEDURE BUTTONS OR USE ANY PERIPHERAL DEVICES SUCH AS A MOUSE In order to ensure that you receive the most benefits from the Windows Vista operating system, it should be registered the first time you use it.

  • Page 60: Starting Windows Xp The First Time

    Windows will then boot up for the first time. As noted above, the first time you initialize your Windows Vista system, the screen will be blank for approximately two minutes. This is normal. During this period, do not disconnect the power supply, press any buttons, or use any peripheral devices such as mouse, keyboard, or remote control.

  • Page 61: Registering Your Lifebook Notebook With Fujitsu

    Several additional windows will appear, prompting you to enter a name and description for your computer, an Administrator password, and a domain name. Read the instructions on the screens carefully and fill in the information as directed. You will then be automatically connected to the Internet, if you have an appropriate connection available. If an automatic connection is not possible, you will be asked about how you dial out from where you will be using your LifeBook notebook.

  • Page 62: Fujitsu Driver Update Utility

    Windows XP Systems The first time you boot up your system, you will see an icon called Click Me! in the Start menu. We highly recommend that you install the ClickMe! utility the first time you boot up. When you click the Click Me! icon, your system will automatically create the related icons in the system tray in the bottom right of the screen.

  • Page 63: Power Management

    Power Management Your notebook has many options and features for conserving battery power. Some of these features are automatic and need no user intervention, such as those for the internal modem. However, others depend on the parameters you set to best suit your operating conditions, such as those for the display brightness. Internal power management for your notebook may be controlled from settings made in your operating system, pre-bundled power management application, or from settings made in BIOS setup utility.

  • Page 64: Hibernation (Save-To-Disk) Feature

    • Timing out from lack of activity. • Allowing the battery to reach the Dead Battery Warning condition. Your notebook’s system memory typically stores the file on which you are working, open application information, and any other data required to support operations in progress. When you resume operation from Sleep mode, your notebook will return to the point where it left off.

  • Page 65: Windows Power Management

    Enable or Disable the Hibernation Feature Windows Vista: The default settings are not enabled. To enable or disable the Hibernation feature follow these steps: From the Start menu, select Control Panel, then select Power Options (if you are in Control Panel Home view, you’ll need to click Mobile PC before clicking Power Options).

  • Page 66: Powering Off

    URNING OFF YOUR NOTEBOOK WITHIN YOU START THE NEXT TIME Powering Off Before turning off the power, check that the hard drive/optical drive access indicator is off. If you turn off the power while accessing a disk there is a risk of data loss. To ensure that your notebook shuts down without error, use the Windows shut down procedure.
  • Page 67 Click the [Start] button. Move the mouse over the small arrow at the bottom right of the right-hand pane. Select Shut Down from the list. If you are going to store your notebook for a month or more, see the Care and Maintenance section. 62 - Power Management...

  • Page 68: Lithium Ion Battery

    Chapter 3 User-Installable Features Lithium ion Battery Your LifeBook notebook has a Lithium ion battery that provides power for operating your notebook when no external power source is available. The battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals or other hazards.

  • Page 69: Recharging The Batteries

    • CTUAL BATTERY LIFE WILL VARY BASED ON SCREEN BRIGHTNESS MANAGEMENT SETTINGS DRIVE USAGE MAY ALSO HAVE A SIGNIFICANT IMPACT ON BATTERY LIFE CAPACITY IS REDUCED AS THE BATTERY AGES SHOULD REPLACE IT WITH A NEW ONE • NDER FEDERAL THEM IN THE TRASH PROPERLY HECK WITH YOUR LOCAL GOVERNMENT AUTHORITY FOR DETAILS REGARDING RECYCLING...
  • Page 70 Low Battery State When the battery is running low, your notebook will beep every 15 seconds and the Battery Level indicator will flash. If you do not respond to the low battery alarm, the batteries will continue to discharge until they are too low to operate. When this happens there will be a multiple beep alarm and the Battery Level indicator will show a dead battery.

  • Page 71: Replacing The Battery

    Your LifeBook notebook comes with one battery pack, but it’s a good idea to purchase a second one. By keeping a spare battery fully charged, you can immediately swap with one that is not charged. If the system is not plugged into a power adapter, the battery can only be replaced by cold-swapping; doing otherwise could result in loss of data.

  • Page 72: Pc Cards

    PC Cards Your LifeBook supports Type I and Type II PC Cards which can perform a variety of functions. Some available PC Cards include: • Gigabit Ethernet Local area network (LAN) cards • S-ATA II cards • IEEE1394 cards • IEEE802.11n WLAN cards For further information, refer to the instructions supplied with your PC card.

  • Page 73: Installing Pc Cards

    PC Cards are installed in the PC Card slot. To install a PC Card: • NSTALLING OR REMOVING A PROCESS MAY DAMAGE THE CARD AND • O NOT INSERT A YOU MAY PERMANENTLY DAMAGE THE CARD OU MAY BE REQUIRED TO LOG ON AS AN ROUP TO COMPLETE THIS PROCEDURE POLICY SETTINGS MAY ALSO PREVENT YOU FROM COMPLETING THIS PROCEDURE See your PC Card manual for instructions on the installation of your card.

  • Page 74: Smart Card Reader

    Unlock the card from the slot by pressing the eject button associated with the slot in which the card is located. When pressed, the button will pop out. Firmly press the button again until it is flush with the notebook. This will eject the card slightly out of the slot allowing you to remove the card.

  • Page 75: Compactflash Cards

    CompactFlash Cards Your Fujitsu LifeBook notebook supports CompactFlash (CF) cards, which can perform a variety of functions. Some available CompactFlash Cards: • Memory cards • Fax/data modem cards • Local area network (LAN) cards For further information, refer to the instructions supplied with your PC Card. CompactFlash Eject Button Figure 25.

  • Page 76: Installing Compactflash Cards

    CompactFlash Cards are inserted in the CompactFlash Card slot. To insert a CompactFlash Card, follow these steps: • NSERTING OR REMOVING A BOOTUP PROCESS MAY DAMAGE THE CARD AND • O NOT INSERT A ON THE CARD AS YOU MAY PERMANENTLY DAMAGE THE CARD See your CompactFlash Card manual for specific instructions on the insertion of your card.

  • Page 77: Removing Compactflash Cards

    To remove a CompactFlash Card, follow these easy steps: INDOWS HAS A SHUTDOWN PROCEDURE FOR BEFORE REMOVING A CARD CORRECT PROCEDURE ARDWARE ICON IN THE SYSTEM TRAY See your CompactFlash Card manual for specific instructions on removing your card. Some CompactFlash Cards may require your notebook to be in Standby Mode or Off while removing them.

  • Page 78: Memory Upgrade Module

    Memory Upgrade Module Your notebook has been configured with a minimum of 512 MB of high speed DDR2 533 MHz RAM factory installed. In addition to the installed memory, there is a second DIMM slot in which you can install a second module.
  • Page 79 Insert the memory upgrade module at a 45° angle. Press the connector edge of the module firmly down and into the connector until it lodges under the retaining clip. You will hear a click when it is properly in place. Replace the memory compartment cover.

  • Page 80: Checking The Memory Capacity

    Removing a Memory Upgrade Module Turn off power to your notebook and remove any attached power adapter (AC or auto/airline). Make sure you are properly grounded. Make sure that all connector covers are closed. Turn the notebook bottom side up, with the battery toward you.
  • Page 81 F THE TOTAL MEMORY DISPLAYED IS INCORRECT CHECK THAT YOUR MEMORY UPGRADE MODULE IS . (I PROPERLY INSTALLED F THE MODULE IS PROPERLY INSTALLED AND THE CAPACITY IS STILL NOT CORRECTLY RECOGNIZED ROUBLESHOOTING ON PAGE 76 - Memory Upgrade Module...

  • Page 82: Device Ports

    Device Ports Your Fujitsu LifeBook notebook and the optional Port Replicator come equipped with multiple ports to which you can connect external devices including: disk drives, keyboards, modems, printers, etc. Modem (RJ-11) Telephone Jack The modem (RJ-11) telephone jack is used for an internal modem. (See Figure 3 for location). To connect the telephone cable follow these easy steps: Align the connector with the port opening.

  • Page 83: Internal Lan (Rj-45) Jack

    HE INTERNAL MODEM IS NOT INTENDED FOR USE WITH TO A IGITAL AS IT MAY CAUSE SERIOUS DAMAGE TO THE MODEM OR YOUR NOTEBOOK MANUFACTURER BEFORE FIND OUT YOU CONNECT YOUR MODEM • HE INTERNAL MODEM IS DESIGNED TO THE HIGHEST ALLOWED BY MAXIMUM SPEED IS •...

  • Page 84: Headphone/Line-Out Jack

    The headphone/line-out jack allows you to connect headphones or powered external speakers to your notebook. (See Figure 3 for location.) Your headphones or speakers must be equipped with a 1/8” (3.5 mm) stereo mini-plug. In order to connect headphones or speakers follow these easy steps: Align the connector with the port opening.

  • Page 85: Troubleshooting Your Lifebook

    Chapter 4 Troubleshooting Your LifeBook Troubleshooting There may be occasions when you encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices that can be solved by replacing the device. The information in this section helps you isolate and resolve some of these straightforward issues and identify failures that require service.
  • Page 86 If the problem has not been resolved, refer to the Troubleshooting Table, that follows, for more detailed troubleshooting information. F YOU KEEP NOTES ABOUT WHAT YOU HAVE TRIED ABLE TO HELP YOU MORE QUICKLY BY GIVING ADDITIONAL SUGGESTIONS OVER THE PHONE If you have tried the solutions suggested in the Troubleshooting Table without success, contact your support representative: Toll free: 1-800-8Fujitsu (1-800-838-5487)

  • Page 87: Specific Problems

    Using the Troubleshooting Table When you have problems with your LifeBook notebook, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions.

  • Page 88: Problem

    Problem Possible Cause Audio Problems There is no sound coming The software volume from the built-in speakers. control is set too low. Headphones are plugged into your notebook. Software driver is not configured correctly. The speakers have been muted using the Volume icon in the sys- tem tray.

  • Page 89: Hard Drive Problems

    Problem Possible Cause You cannot access your The floppy disk drive optional external floppy may not be properly disk. installed. (continued) Security is set to protect access to floppy disk data. Hard Drive Problems You cannot access your The wrong drive desig- hard drive.

  • Page 90: Memory Problems

    Problem Possible Cause You have connected an Your operating system external keyboard or a software is not setup mouse and it seems to be with correct software locking up the system. driver for that device. The system crashed. Memory Problems Your System Properties Your memory upgrade screen does not show the...

  • Page 91: Pc Card Problems

    Problem Possible Cause PC Card Problems A card inserted in the PC The card is not properly Card slot t does not work or installed. is locking up the system. The card may have been installed while an application was running, so your notebook is not aware of its installation.
  • Page 92 Problem Possible Cause You turn on your LifeBook Power adapter has no notebook and nothing power from the AC out- seems to happen. let, airplane jack, or the (continued) car’s cigarette lighter. Your LifeBook notebook The power manage- turns off all by itself. ment parameters are set for auto timeouts which are too short for...

  • Page 93: Shutdown And Startup Problems

    Problem Possible Cause The battery seems to You are running a pro- discharge too quickly. gram that uses a lot of power due to frequent hard drive or optical drive access, or use of a modem, or LAN PC card. The power savings fea- tures may be disabled.

  • Page 94: Video Problems

    Problem Possible Cause System powers up and dis- You have a secured plays power on information system requiring a but fails to load the operat- password to load your ing system. (continued) operating system. An error message is dis- Power On Self Test played on the screen during (POST) has detected a the notebook (boot)
  • Page 95 Problem Possible Cause The notebook turned on Power On Self Test has with a series of beeps and detected a failure which the built-in display is blank. does not allow the dis- play to operate. The display goes blank by The notebook has gone itself after you have been into Video timeout,...

  • Page 96: Miscellaneous Problems

    Problem Possible Cause The application display You are running a pro- uses only a portion of your gram that does not sup- screen and is surrounded port the system’s native by a dark frame. pixel resolution and dis- play compression is enabled.

  • Page 97: Power On Self Test Messages

    Power On Self Test Messages The following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual.
  • Page 98 *Incorrect Drive B type – run SETUP Type of floppy drive B: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.
  • Page 99 *Parity Check 1 nnnn Parity error found in the system bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is a potentially data destroying failure. Contact your support representative.
  • Page 100 *System battery is dead – Replace and run SETUP The BIOS CMOS RAM memory hold up battery is dead. This is part of your BIOS and is a board mounted battery which requires a support representative to change. You can continue operating but you will have to use setup utility default values or reconfigure your setup utility every time you turn off your notebook.

  • Page 101: Modem Result Codes

    The operating system and application software that is factory installed detects the modem characteristics and provides the necessary command strings to operate the modem. The internal modem operation is controlled by generic AT commands from the operating system and application software. The standard long form result codes may, in some cases, be displayed on your screen to keep you informed of the actions of your modem.

  • Page 102: Restoring Your Pre-Installed Software

    Restoring Your Pre-installed Software The Drivers and Applications Restore (DAR) disc contains sets of device drivers and Fujitsu utilities (in specific directories) that are unique to your computer configuration for use as documented below. • • Re-installing Individual Drivers and Applications The Drivers and Applications CD can be used to selectively re-install drivers and/or applications that may have been uninstalled or corrupted.

  • Page 103: Restoring The Operating System For Windows Xp Systems

    HE COMPONENTS LISTED ARE COLOR THAT THE COMPONENT CAN BE INSTALLED INSTALLED SEPARATELY CAN BE REINSTALLED COMPONENT IS ALREADY INSTALLED In the list, check off all components you want to install. If you want to install all components, click [Select All]. Clicking [Select All] will select all of the blue-coded components;...

  • Page 104: Restoring The Operating System For Windows Vista Systems

    BOOT Priority Change Before restoring an image, you must first verify that the system is set up to boot from the optical drive. To verify/change the boot-up priority (rather than booting-up from the hard drive or an external floppy disk drive), perform the following steps: Power on your system.
  • Page 105 Methods for accessing the utilities Certain LifeBooks have the Recovery and Utility applets pre-installed on a hidden drive. Other systems require that the Recovery and Utility disc be used (or in the event the hard disk has been reformatted). In order to determine the method for accessing the Recovery and Utility applet, perform the following procedures in order.
  • Page 106 Running Recovery and Utility from the disc • HE USE OF THIS DISC REQUIRES THAT YOU HAVE A DEVICE CAPABLE OF READING SYSTEM OU WILL NEED TO ATTACH AN EXTERNAL PLAYER DEVICES VISIT OUR • HIS DISC CAN ONLY BE USED WITH THE SYSTEM WITH WHICH IT WAS PURCHASED BOOT Priority Change Before restoring an image, you must first verify that the system is set up to boot from the optical drive.
  • Page 107 Recovery and Utility tabs Diagnostics tab: The Diagnostics tool is designed for use by IT professionals. It is not likely you will need to use this tool. When you select devices from the Diagnosis window then click [Execute], several tests are performed on the selected components.

  • Page 108: Automatically Downloading Driver Updates

    Automatically Downloading Driver Updates Your system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. The FDU icon should appear in the system tray at the bottom right of your screen (roll the cursor over the icons to find the correct one).

  • Page 109: Care And Maintenance

    Chapter 5 Care and Maintenance Caring for your LifeBook Notebook If you use your Fujitsu LifeBook notebook carefully, you will increase its life and reliability. This section provides some tips for looking after the notebook and its devices. • • HE SYSTEM CONTAINS COMPONENTS THAT CAN BE SEVERELY DAMAGED BY ELECTROSTATIC DISCHARGE O MINIMIZE RISK TO THE COMPONENTS OBSERVE THE FOLLOWING PRECAUTIONS...
  • Page 110 • Make a habit of transporting it in a suitable carrying case. • Do not attempt to service the computer yourself. Always follow installation instructions closely. • Keep it away from food and beverages. • To protect your notebook from damage and to optimize system performance, be sure to keep all air all vents unobstructed, clean, and clear of debris.

  • Page 111: Cleaning Your Lifebook Notebook

    • Always disconnect the power plug. (Pull the plug, not the cord.) • Clean your LifeBook notebook with a damp, lint-free cloth. Do not use abrasives or solvents. • Use a soft cloth to remove dust from the screen. Never use glass cleaners. •...

  • Page 112: Storing Your Lifebook Notebook

    • Wipe the surface with a soft cloth wipe and a 50% ethanol solution or use another ethanol-based germicide which has been registered as a hospital disinfectant by the EPA. • SE OF INCORRECT CLEANERS CAN RESULT IN OPTICAL IMPAIRMENT OF THE COMPUTER LWAYS REFER TO THE CLEANER MANUFACTURER SHEETS FOR PROPER HANDLING AND USE OF THE PRODUCTS...

  • Page 113: Traveling With Your Lifebook Notebook

    • Do not transport your notebook while it is turned on. • It is recommended that you carry your notebook with you while traveling, rather than checking it in as baggage. • Always bring your System Recovery disc that came with your notebook when you travel. If you experience system software problems while traveling, you may need it to correct any problems.

  • Page 114: Batteries

    Caring for your Batteries • Always handle batteries carefully. • Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). • Do not carry loose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects.

  • Page 115: Media Care

    Caring for your Media (DVD/CD/CD-R) Media discs are precision devices and will function reliably if given reasonable care. • Always store your media disc in its case when it is not in use. • Always handle discs by the edges and avoid touching the surface. •...

  • Page 116: Pc/Compactflash Cards

    • Avoid using or storing the drive where it will be subjected to shock or vibration. • Do not disassemble or dismantle the optical drive. • Use of a commercially available lens cleaner is recommended for regular maintenance of your drive.

  • Page 117: System Specifications

    Chapter 6 System Specifications Specifications This section provides the hardware and environmental specifications for your Fujitsu LifeBook notebook. Specifications of particular configurations will vary. Configuration Label The configuration label located on the bottom of your notebook contains specific information regarding the options you’ve chosen for your notebook.

  • Page 118: Microprocessor

    Intel Core 2 Duo microprocessor (To determine the processor speed, right-click My Computer, select Properties, then select the General tab.) Chipset Intel 945GM Memory System Memory • DDR2-533 MHz SDRAM dual-channel memory module. • Two DIMM slots; upgradeable to 4 GB of total memory (2 GB x 2). Note that when 4 MB of memory is installed in a Windows Vista system, approximately 3.25 GB is addressable memory;...

  • Page 119: Audio

    • Realtek codec ALC262 with 2-channel High Definition (HD) audio. • Headphones: Stereo headphone/line-out jack, 3.5 mm, 1 V • Microphone: Stereo microphone/line-in jack, 3.5 mm, 100 mV • Two built-in boxless stereo speakers Mass Storage Device Options Floppy Disk Drive Optional external USB 3.5"...

  • Page 120: Security Features

    Theft Prevention Lock Slot Lock slot for use with physical restraining security systems. Fingerprint Sensor Optional fingerprint sensor in some configurations Trusted Platform Module (TPM) The embedded TPM 1.2 protects digital identification and data, and authenticates you to your network. It also allows you to securely store private keys and certificates for file and folder encryption, Web, email, digital signature and passwords.

  • Page 121: Keyboard

    • One LAN (RJ-45) jack • One stereo headphone/line-out jack. (See Audio specifications) • One stereo microphone/line-in jack. (See Audio specifications) • One 80-pin connector for docking devices • Embedded Smart Card Reader (requires optional Smart Card holder and third-party application) On the Optional Port Replicator: •...

  • Page 122: Power

    Power Batteries One 6-cell Lithium ion battery, rechargeable, 7.2V, 7800 mAh, 56.2 Whr AC Adapter Autosensing 100-240V AC, 60W, supplying 16V DC, 3.75A, to the LifeBook notebook, Fujitsu Model FPCAC58AP, which includes an AC cable. Power Management Conforms to ACPI (Advanced Configuration and Power Interface) standards. Dimensions and Weight Overall Dimensions Approximately 10.55"(w) x 9.02"(d) x 1.29"(h) (268 mm x 229 mm x 32.7 mm)

  • Page 123: Popular Accessories

    For ordering or additional information on Fujitsu accessories, please visit our Website at www.shopfujitsu.com or call 1-800-FUJITSU. Pre-Installed Software Depending on your operating system, your notebook comes with pre-installed software for playing audio and video files of various formats. In addition there is file transfer software, virus protection software and power management software.

  • Page 124: Learning About Your Software

    Tutorials All operating systems and most application software have tutorials built into them. We recommend that you step through the tutorial before you use an application. Manuals Included with your notebook you will find manuals for your installed operating system and other pre- installed software.
  • Page 125 Fujitsu Driver Update Utility The Fujitsu Driver Update (FDU) utility is pre-installed on your system. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. See “Automatically Downloading Driver Updates” on page 103. Fujitsu HotKey Fujitsu HotKey lets you control the display brightness of your notebook in order to maximize battery life.
  • Page 126 OmniPass Fingerprint Recognition Software (optional) The optional fingerprint sensor uses Softex OmniPass which provides password management capabilities to Microsoft Windows operating systems. OmniPass lets you use a "master password" for all Windows, applications, and on-line passwords. The software also presents a convenient user interface through which you can securely manage passwords, users, and multiple identities for each user.

  • Page 127: Glossary

    Glossary AC Adapter A device which converts the AC voltage from a wall outlet to the DC voltage needed to power your LifeBook notebook. Access point Wireless network device used to bridge wireless and wired network traffic. ACPI Advanced Configuration and Power Interface Active-Matrix Display A type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.
  • Page 128 ADSL Asymmetric Digital Subscriber Line. Technology for transporting high bit-rate services over ordinary phone lines. Accelerated Graphics Port. Graphics port specifically designed for graphics-intensive devices, such as video cards and 3D accelerators. Auto/Airline Adapter A device which converts the DC voltage from an automobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your LifeBook notebook.
  • Page 129 An electrical circuit which passes data between the CPU and the sub-assemblies inside your LifeBook notebook. Byte 8 bits of parallel binary information. Cache Memory A block of memory built into the micro-processor which is much faster to access than your system RAM and used in specially structured ways to make your overall data handling time faster.
  • Page 130 COM Port Abbreviation for communication port. This is your serial interface connection. Command An instruction which you give your operating system. Example: run a particular application or format a floppy disk. Configuration The combination of hardware and software that makes up your system and how it is allocated for use. Cathode Ray Tube.
  • Page 131 DIMM Dual-in-line memory module. Disk A spinning platter of magnetic data storage media. If the platter is very stiff it is a hard drive, if it is highly flexible it is a floppy disk, if it is a floppy disk in a hard housing with a shutter it is commonly called a diskette.
  • Page 132 Disk Operating System (MS-DOS is a Microsoft Disk Operating System). Driver A computer program which converts application and operating system commands to external devices into the exact form required by a specific brand and model of device in order to produce the desired results from that particular equipment.
  • Page 133 Floppy Disk A spinning platter of magnetic data storage media which is highly flexible. Gigabyte. One billion bytes. Hard drive A spinning platter of magnetic data storage media where the platter is very stiff. Input/Output. Data entering and leaving your notebook in electronic form. I/O Port The connector and associated control circuits for data entering and leaving your notebook in electronic form.
  • Page 134 IEEE802.11g Wireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11g devices operate in the 2.4 GHz ISM band. Infrared Light just beyond the red portion of the visible light spectrum which is invisible to humans. Infrastructure A name of a wireless LAN configuration.
  • Page 135 An abbreviation for infrared. IrDA Infrared Data Association. An organization which produces standards for communication using infrared as the carrier. Interrupt Request. An acronym for the hardware signal to the CPU that an external event has occurred which needs to be processed. Kilobyte.
  • Page 136 MAC Address Media Access Control Address. A unique physical address of a network card. For Ethernet, the first three bytes are used as the vendor code, controlled and assigned by IEEE. The remaining three bytes are controlled by each vendor (preventing overlap), therefore, every Ethernet card is given a unique physical address in the world, being assigned with a different address from other cards.
  • Page 137 Maximum Transmission Unit The maximum data size that can be transferred at a time through the Internet or other networks. You can set a smaller MTU size to obtain successful communication, if you have difficulty transferring data due to the fact that the maximum size is too large. Network key Data that is used for encrypting data in data communication.
  • Page 138 Partition A block of space on a hard drive which is set aside and made to appear to the operating system as if it were a separate disk, and addressed by the operating system accordingly. PCMCIA PCMCIA is a trademark of the Personal Computer Memory Card International Association. The Personal Computer Memory Card International Association is an organization that sets standards for add-in cards for personal computers.
  • Page 139 Program An integrated set of coded commands to your computers telling your hardware what to do and how and when to do it. Protocol Procedures and rules use to send and receive data between computers. - Method of sending and receiving data - Process used to handle communication errors Conditions required for communication are organized in procedures for correct transfer of information.
  • Page 140 Read Only Memory. A form of memory in which information is stored by physically altering the material. Data stored in this way can not be changed by your notebook and does not require power to maintain it. SDRAM Synchronous Dynamic Random Access Memory. Serial Port A connection to another device through which data is transferred one bit at a time on a single wire with any other wires only for control of the device not for transfer of data.
  • Page 141 Status Indicator A display which reports the condition of some portion of your hardware. On your LifeBook notebook this is an LCD screen just above the keyboard. Stereo (audio) A system using two channels to process sound from two different sources. Subnet mask TCP-IP network is controlled by being divided into multiple smaller networks (subnets).
  • Page 142 Thin Film Transistor – A technology for flat display panels which uses a thin film matrix of transistors to control each pixel of the display screen individually. Underwriters Laboratories – An independent organization that tests and certifies the electrical safety of devices.

  • Page 143: Regulatory Information

    Regulatory Information Notice Changes or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment. FCC NOTICES Notice to Users of Radios and Television This equipment has been tested and found to comply with the limit for class B digital devices, pursuant to parts 15 of the FCC Rules.
  • Page 144 Notice to Users of the US Telephone Network This equipment complies with Part 68 of the FCC rules, and the requirements adopted by ACTA. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment;...
  • Page 145 The equipment cannot be used on public coin service provided by the telephone company. Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commission or corporation commission for information). If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this computer does not disable your alarm equipment.
  • Page 146 connect this equipment to the local telecommunication facilities. The user should be aware that compliance with the certification standards does not prevent service degradation in some situations. Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility. Any repairs or alterations not expressly approved by Fujitsu or any equipment failures may give the telecommunication company cause to request the user to disconnect the equipment from the telephone line.
  • Page 147 connecter cet équipement aux installations de télécommunications locales. L’utilisateur est averti que même la conformité aux normes de certification ne peut dans certains cas empêcher la dégradation du service. Les réparations de l’équipement de télécommunications doivent être effectuées par un service de maintenance agréé...

  • Page 148: Appendix A: Wlan User's Guide

    Appendix A: WLAN User’s Guide FCC Regulatory Information Please note the following regulatory information related to the optional wireless LAN device. Regulatory Notes and Statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones.
  • Page 149 Regulatory Information/Disclaimers Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
  • Page 150 FCC Radio Frequency Exposure statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the Wireless LAN antenna (located on the top edge of the LCD screen) and your body.

  • Page 151: Before Using The Optional Wireless Lan

    Before Using the Optional Wireless LAN This manual describes the procedures required to properly set up and configure the optional integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the manual). Before using the WLAN device, read this manual carefully to ensure it's correct operation. Keep this manual in a safe place for future reference.

  • Page 152: Wireless Lan Modes Using This Device

    Wireless LAN Modes Using this Device Ad Hoc Mode "Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer fashion. That is why Ad Hoc networks are also known as peer-to-peer networks.
  • Page 153 Access Point (Infrastructure) Mode Infrastructure mode refers to a wireless network architecture in which devices communicate with wireless or wired network devices by communicating through an Access Point. In infrastructure mode, wireless devices can communicate with each other or with a wired network. Corporate wireless networks operate in infrastructure mode because they require access to the WLAN in order to access services, devices, and computers (e.g., file servers, printers, databases).

  • Page 154: Wireless Network Considerations

    How to Handle This Device The WLAN device comes pre-installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The operating system that your mobile computer comes with has been pre-configured to support the WLAN device. Wireless Network Considerations •...
  • Page 155 The Wireless LAN/Bluetooth On/Off Switch will power off both the optional wireless LAN and Bluetooth devices at the same time. To enable or disable either one of the devices individually, perform the following steps: Slide the Wireless LAN/Bluetooth on/off switch to On position. In the Control Panel, double-click the Fujitsu Radio Control icon.

  • Page 156: Activating The Wlan Device

    Windows XP: Deactivation using Atheros Client Utility software Click [Start] > Program Files > Atheros > Atheros Client Utility. Choose Action and click Disable Radio. Activating the WLAN Device Activation of the WLAN device can be accomplished using the same methods as the deactivation process •...

  • Page 157: Configuring The Wireless Lan

    Configuring the Wireless LAN The optional WLAN device can be configured to establish wireless network connectivity using the software that is built into Windows Vista. Support for most industry standard security solutions is contained in this software. Pre-defined parameters will be required for this procedure. Please consult with your network administrator for these parameters: Configuring the WLAN Using Windows Vista Click the Start button, then select Control Panel.

  • Page 158: Configuring The Wlan Using Windows Xp

    Procedure Click the Start button, then select Control Panel. If the Control Panel is not in Classic View, select Classic View from the left panel. Double-click the Network Connections icon. Double-click on the Wireless Network Connection icon. Choose a wireless network. Click [Connect].

  • Page 159: Troubleshooting The Wlan

    Troubleshooting the WLAN Troubleshooting Causes and countermeasures for troubles you may encounter while using your wireless LAN are described in the following table. Problem Possible Cause Unavailable Incorrect network network name (SSID) or connection network key Weak received signal strength and/or link quality Possible Solution Ad hoc connection: verify that the network names (SSID’s) and...
  • Page 160 Problem Possible Cause Unavailable The WLAN device network has been connection deactivated or disabled (continued) The computer to be connected is turned off RF interference from Access Points or other wireless networks Wireless network authentication has failed Incorrectly configured network settings Incorrect IP address configuration...

  • Page 161: Wlan Specifications

    WLAN Specifications Specifications Item Type of network Transfer rate Active frequency Typical operating distances** Number of channels Security Maximum recommended number of computers to be connected over wireless LAN (during ad hoc connection) Specification Atheros Super AG (802.11a+b/g) WLAN device conforms to IEEE 802.11a and 802.11b/g (Wi-Fi based)* •...
  • Page 162 * “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of wireless LAN (Wi-Fi Alliance) has been passed. ** The communication ranges shown above will increase or decrease depending on factors such as number of walls, reflective material, or interference from external RF sources.

  • Page 163: Using The Bluetooth Device

    What is Bluetooth Bluetooth technology is designed as a short-range wireless link between mobile devices, such as laptop computers, phones, printers, and cameras. Bluetooth technology is used to create Personal Area Networks (PANs) between devices in short-range of each other.
  • Page 164 FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The Bluetooth antenna is located on the front edge of the right palm rest and is exempt from minimum distance criteria due to its low power. The transmitters in this device must not be co-located or operated in conjunction with any other antenna or transmitter.

  • Page 165: Appendix B: Fingerprint Sensor Device

    Appendix B: Fingerprint Sensor Device Introducing the Optional Fingerprint Sensor Device Your system may have an optional fingerprint sensor device below the Touchpad, between the left and right buttons. This also serves as a scroll button. FINGERPRINT SENSOR CAN BE USED FOR SCROLLING SENSOR THE SAME AS YOU WOULD USE A SCROLL BUTTON Figure 31.

  • Page 166: Getting Started

    • Log onto Windows • Resume from sleep mode • Cancel a password-protected screen saver • Log into web sites that require a username and password After you have “enrolled” - or registered - your fingerprint, you can simply swipe your fingertip over the sensor for the system recognize you.
  • Page 167 • The Softex program group in the Programs group of the Start menu System Requirements The OmniPass application requires space on your hard drive; it also requires specific Operating Systems (OS’s). The minimum requirements are as follows: • Windows Vista operating system •...
  • Page 168 Verifying Information about OmniPass After you have completed installing OmniPass and restarted your system, you may wish to check the version of OmniPass on your system. To check the version information of OmniPass: From the Windows Desktop, double-click the key-shaped OmniPass icon in the taskbar (usually located in the lower right corner of the screen), Click the Start button, select Settings, and click Control Panel.

  • Page 169: User Enrollment

    User Enrollment Before you can use any OmniPass features you must first enroll a user into OmniPass. Master Password Concept Computer resources are often protected with passwords. Whether you are logging into your computer, accessing your email, e-banking, paying bills online, or accessing network resources, you often have to supply credentials to gain access.
  • Page 170 HE ENROLLMENT PROCEDURE ASSUMES YOU HAVE NO HARDWARE AUTHENTICATION DEVICES OR ALTERNATE STORAGE LOCATIONS THAT YOU WISH TO INTEGRATE WITH SUCH FUNCTIONALITY Basic Enrollment The Enrollment Wizard will guide you through the process of enrolling a user. Unless you specified otherwise, after OmniPass installation the Enrollment Wizard will launch on Windows login.
  • Page 171 Enrolling a Fingerprint Enrolling a fingerprint will increase the security of your system and streamline the authentication procedure. You enroll fingerprints in the OmniPass Control Center. With an OmniPass user logged in, double-click the system tray OmniPass icon. Select the User Settings tab and click Enrollment under the User Settings area.

  • Page 172: Using Omnipass

    Using OmniPass You are now ready to begin using OmniPass. Used regularly, OmniPass will streamline your authentications. Password Replacement You will often use the password replacement function. When you go to a restricted access website (e.g., your bank, your web-based email, online auction or payment sites), you are always prompted to enter your login credentials.
  • Page 173 Using the following procedure, you can store a set of credentials into OmniPass. These credentials will then be linked to your “master password” or fingerprint. Go to a site that requires a login (username and password), but do not log in yet. At the site login prompt, enter your username and password in the prompted fields, but do not enter the site (do not hit [Enter], [Submit], [OK], or Login).
  • Page 174 HIS SETTING IS MORE CONVENIENT IN THAT WHENEVER YOU GO TO A SITE REMEMBERED WITH THIS SETTING YOU WILL BYPASS ANY AUTHENTICATION PROCEDURE AND GAIN INSTANT ACCESS TO THE SITE UT SHOULD YOU LEAVE YOUR SYSTEM UNATTENDED WITH YOUR ANYONE USING YOUR SYSTEM CAN BROWSE TO YOUR PASSWORD PROTECTED SITES AND GAIN AUTOMATIC ACCESS If you uncheck both boxes in Settings for this Password Site, OmniPass will prompt you for your master password or fingerprint authentication device.
  • Page 175 Logging into Windows with a Fingerprint Device When logging into Windows with a fingerprint device, the fingerprint capture window will now appear next to the Windows Login screen. Place your enrolled fingertip on the sensor to authenticate. You will be simultaneously logged into Windows and OmniPass. The capture window will also appear if you have used Ctrl-Alt-Del to lock a system, and the fingerprint device can be used to log back in as stated above.
  • Page 176 The two check boxes in Manage Passwords govern whether OmniPass prompts you to authenticate or directly logs you into the remembered site. OmniPass will overwrite an old set of credentials for a website if you attempt to use Remember Password on an already remembered site. The exception to the above rule is when resetting the Windows password.

  • Page 177: Configuring Omnipass

    [Apply] to ensure the settings are saved. If you log in to OmniPass with a fingerprint device, you will automatically be logged in to the default identity for that OmniPass user. You can choose the identity with which you are logging in if you login using "master password". Choosing User Identity during Login To choose your identity during login, type your username in the User Name: field.
  • Page 178 process backs up all remembered sites, credentials, and enrolled fingerprints for an OmniPass user. All OmniPass data for a user is backed up to a single encrypted database file. During the import process, the Windows login of the exported user is required. If the proper credentials cannot be supplied, the user profile will not be imported •...

  • Page 179: Omnipass Control Center

    will need User Name, Password, and Domain. If you don’t remember the value for Domain, in a PC or SOHO environment Domain should be your computer name. OmniPass will notify you if the user was successfully imported. Things to Know Regarding Import/Export •...
  • Page 180 double-click the Softex OmniPass icon. User Management The User Management tab has two major interfaces: Add/Remove User and Import/Export User. Import/Export User functionality is documented in “Exporting and Importing Users” on page 172. Add/Remove User functionality is straightforward. If you click Adds a new user to OmniPass you will start the OmniPass Enrollment Wizard. The Enrollment Wizard is documented in “User Enrollment”...

  • Page 181: Troubleshooting

    System Settings The OmniPass Startup Options interface can be found in the System Settings tab. With these options you can specify how your OmniPass Logon is tied to your Windows Logon. The first option, Automatically log on to OmniPass as the current user, will do just as it says; during Windows login, you will be logged on to OmniPass using your Windows login credentials.
  • Page 182 Cannot add a User with a Blank Password to OmniPass If you experience difficulties adding a user with a blank password to OmniPass, you may need to adjust your local security settings. First attempt the procedure explained in the Cannot add Windows user to OmniPass section.

  • Page 183: Index

    Index About This Guide adapter indicator plug adapters Anti-theft lock slot Application Panel Auto/Airline Adapter Automatically Downloading Driver Updates Battery alarm care cold-swapping conserving power dead faulty increasing life lithium ion battery problems recharging replacing shorted standby mode BIOS guide setup utility Bluetooth, where to find information CapsLock...
  • Page 184 Double-Clicking Dragging Drivers and Application Restore CD Emergency tray release Error Messages External Floppy Disk Drive External Monitor Port Fingerprint Sensor Device enrolling a fingerprint getting started installing OmniPass logging into a remembered site OmniPass authentication toolbar password replacement remembering a password uninstalling OmniPass user enrollment using OmniPass...
  • Page 185 Memory Stick installing Microphone Jack Modem problems Modem Jack Modem Result Codes Mouse problems Numeric Keypad NumLk PC Card access indicator removing slot Pointing Device See Touchpad Port Replicator problems Power AC adapter Auto/Airline adapter failure indicator management problems sources Power Management Power On Self Test Power specifications...
  • Page 186 Theft Prevention Lock Touch Screen calibrating clicking double-clicking dragging Touchpad buttons controls Touchpad Pointing Device Troubleshooting port replicator Universal Serial Bus Ports Unpacking 18, 78 problems Volume control Warranty Windows keys Application key Start keys Windows Vista configuring the WLAN restoring the Operating System Windows XP configuring the Wireless LAN...

This manual is also suitable for:

Lifebook b6230

Table of Contents