About The Optional Accessories; Projection Lens; Input Board; Exhaust Duct Adaptor - Sony SRX-T105 Installation Manual

On lamp break
Should the lamp explode, it is dangerous to be near the
ventilation holes for exhaust. Keep at least 2 m (approx.
6.6 feet) (page 41) away from the projector's ventilation
holes for exhaust.
Note
If someone is likely to enter the dangerous area, attach the
LKRA-001 exhaust duct adaptor to the projector and
install the exhaust duct.
On cleaning
• To keep the cabinet looking new, periodically clean it
with a soft cloth. Stubborn stains may be removed with
a cloth lightly dampened with a mild detergent solution.
Never use strong solvents, such as thinner, benzene, or
abrasive cleansers, since these will damage the cabinet.
• Avoid touching the lens. To remove dust on the lens, use
a soft dry cloth. Do not use a damp cloth, detergent
solution, or thinner.
On repacking
Save the original shipping carton and packing material;
they will come in handy if you ever have to ship your unit.
For maximum protection, repack your unit as it was
originally packed at the factory.
On prohibiting continuous lighting
Continuously lighting the Xenon lamp for 24 hours will
reduce approximately half of its lamp life. Be sure to off
the lamp for an hour or more after continuously lighting for
24 hours.
To light the lamp continuously for 24 hours, it is
recommended to use the lamps alternately. To use the
lamps alternately, select "User-Defined" in "Single" (page
29) under "LAMP SELECT" in the INSTALLATION
window and set the time.
For better image projection
Uniformity may change according to the setting
environment. It is recommended to adjust the uniformity
during setting and adjustment using the optional tool kit
(PCAT). As uniformity may change with each use, it is
recommended to adjust the uniformity regularly
(approximately once every two times the lamp is
replaced).
For purchase of the kit, contact your Sony dealer.
About the Optional
Accessories
The projection lamps of this projector are provided as
optional accessories. Install the lamp houses to the
projector according to your model.
For versatile use of the projector, the optional accessories
mentioned below can be used with the projector. Select to
use them according to your system requirements.
For details on optional accessories, refer to the relevant
operating instructions.
Lamp house
• LKRX-B110 projection lamp house for SRX-T110
• LKRX-B105 projection lamp house for SRX-T105
Lamp for replacement
• LKRX-110 projection lamp for SRX-T110
• LKRX-105 projection lamp for SRX-T105

Projection lens

• LKRL-Z115 1.48- to 1.81-times zoom lens
• LKRL-Z117 1.72- to 2.39-times zoom lens (with zoom/
focus memory function)
• LKRL-Z119 1.81- to 2.94-times zoom lens (with zoom/
focus memory function)
• LKRL-Z122 2.23- to 4.03-times zoom lens (with zoom/
focus memory function)
• LKRL-Z140 3.81- to 7.12-times zoom lens
• LKRL-90 0.9-times fixed focus lens

Input board

• LKRI-001 analog input board
• LKRI-002 HD-SDI (4:2:2) input board
• LKRI-003 HD-SDI/DC-SDI (4:4:4) input board
• LKRI-004 DVI interface board
• LKRI-005 HDCP DVI board

Exhaust duct adaptor

LKRA-001 8-inch exhaust duct adaptor
Note
When LKRA-001 is attached, be sure to use an external
fan with the specified air flow. If the projector does not
exhaust enough heat, the projector becomes hot. This may
cause damage to the parts in the projector.
For details on the air flow specification of the external fan,
refer to the Installation Instructions of LKRA-001.

About the Optional Accessories

5