Advertisement
Assembling the drum module and cymbal pads
Each cymbal pad
PCY135 Cymbal Pad
PCY135
1.
Cymbal Pad
Using the tuning key, loosen the stopper's key bolt.
Drum module
2.
Remove the wing nut, the two felt pads, and the bolt
cover from the cymbal holder.
A cymbal pad's built-in sensor is located close to the
Yamaha logo found on the top surface. In order to
achieve the best performance from your pad, position
it such that the area around the logo can be easily
struck. (See the figure above.)
Drum module
1.
Secure the module holder to the bottom of the drum
module using the module holder screws.
3.
Place the stopper on the cymbal holder.
Module holder
* If the key bolt was not sufficiently loosened in
Module holder
Bottom of drum
Step 1 above, it may not be possible to pass the
screws
module
stopper over the cymbal holder's shaft. In such a
case, loosen the key bolt as much as possible
without removing it.
4.
Replace the bolt cover.
Front side
* Turn the bolt cover to tighten it onto the threaded
section and firmly secure it in place.
2.
Push the module holder into the holder clamp and
tighten the clamp bolt to secure it in place.
Drum module
+
module holder
Push in
Clamp bolt
Holder clamp
Assembling the hi-hat stand
1.
5.
If a drum mat (sold separately) is not available, lay
As shown on the right, loosen the hi-hat clutch's
wing bolt b and remove the hi-hat clutch.
a sheet of cardboard on the floor to prevent it from
being scratched.
* The hi-hat clutch is not required when assembling
the electronic drum kit in the standard fashion de-
2.
Loosen the hi-hat stand's wing bolt a.
scribed in this manual. Instead, the hi-hat clutch
that came with the RHH135 Real Hi-Hat Pad will be
3.
Open up the three legs as shown below and then re-
used.
tighten the wing bolt a to lock them in place.
6.
Remove the hi-hat shaft
4.
Insert the connecting rods into the holes in the frame
.
as shown below.
7.
Insert the hi-hat shaft
go into the lower tube
a
Wing bolt
8.
Insert the upper tube
and tighten the wing bolt c to secure it in place with
the bottom seat approximately half way between the
top of the lower tube c and the top of the hi-hat
shaft
9.
Remove the felt pad from the top of the bottom seat.
It is not required when assembling the electronic
Connecting
drum kit in the standard fashion described in this
rod
manual.
Connecting
rod
5.
With the stopper making full contact with the bottom
surface of the bolt cover as shown below, tighten the
stopper's key bolt using the tuning key.
Stopper
Bolt cover
Key bolt
Full contact
Tuning key
6.
Place one of the felt pads removed in Step 2 on the
cymbal holder.
7.
Mount the pad on the cymbal stand. Lower the pad
Wing nut
into place with the cymbal holder's shaft passing
Felt pads
through the central hole. When mounted, the stop-
per's pin should rest inside the pad's smaller hole.
Bolt cover
* If you were to play your cymbal pad without the
stopper's pin positioned well inside the smaller
hole, the pad could rotate, causing the cable to be
pulled out. It is very important, therefore, to en-
sure that the stopper is secured as shown in Step
Cymbal holder
5 above.
8.
Assemble the felt pad that came with the cymbal
pad.
The second felt pad removed from the cymbal
holder in Step 2 above is not required for assem-
bly.
9.
Tighten the wing nut to secure the pad to the cymbal
holder.
Wing nut
Felt pad that
came with
cymbal
Bolt cover
Cymbal pad
Stopper
Threaded section
Felt pad
Bolt cover
Cymbal holder
Hi-hat clutch
b
from the upper tube
Bottom
seat
from Step 6 as far as it will
and screw in the tip.
over the hi-hat shaft
.
10.
Assemble the RHH135 Real Hi-hat Pad.
* For detailed instructions, refer to the Setting
Up section in the RHH135 Owner's Manual.
Assembling the kick pad
1.
If a drum mat (sold separately) is not available, lay a sheet of cardboard on the
floor to prevent it from being scratched.
2.
Remove the four wing bolts, spring washers, and flat washers from the kick pad
frame, and line up each set nearby in the order of removal.
3.
Join the base section to the frame as shown on the right, and then secure it in
place by assembling the wing bolts, spring washers, and flat washers removed in
the previous step from the base side.
Stopper
Cymbal holder
Arrange the hi-hat stand and the kick pad as shown in Example of standard assembly on the other side of this sheet.
4
Lay a drum mat (sold separately) on the floor underneath the hi-hat stand and the kick pad. Alternatively, you can place card-
NOTICE
board from the drum kit packaging or the like on the floor to prevent it from being scratched.
Connect the pads to the drum module.
5
Connect the output of each pad to the corresponding drum-module input.
1.
Plug the straight ends of the nine-channel snake cable into the trigger input
jacks ([qSNARE] to [oHI-HAT] and [HI-HAT CONTROL]) on the back of the
drum module.
• When using the standard setup, the stickers on each of the snake cable's plugs
will indicate the name of the corresponding pad.
Drum-module rear panel
7
6
5
Stopper
Cymbal pad
Smaller hole
Pin
Nine-channel
Stopper
snake cable
Cymbal holder
Straight
plugs
L plugs
HH CON HI HAT CRASH
Felt pad
Connect the power adaptor to the drum module.
6
Bottom
seat
1.
Plug the power adaptor's DC cord into the
c
the cord clip to secure it in place.
Drum-module rear panel
Cord clip
2.
Using the cable bands, secure the cables to the kit rack at the positions circled in the figure on the right. (
3.
Plug the adaptor's AC cord into a domestic wall socket.
Your electronic drum kit is now ready.
Frame
2.
Plug the L-shaped ends of the nine-channel snake cable into the corresponding
pads.
Locations of pad jacks
4
3
2
1
RIDE
9
8
DTX502 jack names
Straight plug names
TOM3
(as shown on stickers)
1: qSNARE
SNARE
2: wTOM1/!0
TOM1
3: eTOM2/!1
TOM2
4: rTOM3/!2
TOM3
5: tRIDE
RIDE
6: yCRASH
CRASH
7: uKICK/i
KICK
8: oHI-HAT
HI HAT
9: HI HAT CONTROL
HH CON
3.
In the case of snare and tom pads, wrap the cables around the cable clips to pre-
vent them from being pulled out.
NOTICE
KICK
SNARE TOM1 TOM2 TOM3 RIDE
connector. Hook the power adaptor's DC cord around
connector
* For instructions on turning on the drum module, producing sounds, and other subsequent steps,
Spring washer
Flat washer
Wing bolt
Frame
Base
CRASH
HI HAT HI CON
SNARE
TOM2
TOM1
KICK
Excessive bending can damage pad cables. Ensure, therefore,
that these cables are not bent at an extreme angle when
wrapped around the clips.
)
please refer to the Owner's Manual that came with the module.
Advertisement
