Remote Control; General - Insignia NS-42L260A13A User Manual

Insignia 42" LCD TV
Problem Solution
Dotted lines or stripes
• Make sure that the antenna or cable TV is
appear on the screen.
• If you are using an antenna, the digital channel
• If you are using an antenna and the signal
• Make sure that the video cables are connected
• The video cable(s) you are using may be bad. Try
• Other devices (for example, a surround sound
Double images.
• Use a highly directional outdoor antenna, cable
The picture has a few bright
• A few bright or dark spots on an LCD screen is
or dark spots.
Good picture, but no sound.
•
• Make sure that the sound is not muted.
• Make sure you do not have headphones
• Make sure that the correct audio mode is
• Make sure that the audio cables are connected
• Make sure that the antenna or cable TV is
• If you are using an antenna, the digital channel
• The audio cable(s) you are using may be bad. Try
Poor picture.
• Make sure that the room is not too bright. Light
• If an S-VHS camera or a camcorder is connected
Good sound but poor color.
•
Audio noise.
• Other devices (for example, a surround sound
connected correctly and securely. See
"Connecting a cable or satellite box" on page
or "Connecting an antenna or cable TV (no
on page 13.
signal may be low. To check the digital channel
signal strength, see "Checking the digital signal
strength" on page 30.
strength is low, adjust the antenna or use a
highly directional outdoor antenna or set-top
antenna with a built-in amplifier.
securely to your TV.
a new set.
receiver, external speakers, fans, or hair dryers)
may be interfering with your TV. Try turning off
one device at a time to determine which device
is causing interference. After you have
determined which device is causing
interference, move it further from the TV to
eliminate the interference.
TV, or satellite TV.
normal. It does not affect the operation of
your TV.
Increase the volume.
connected. When headphones are connected,
no sound comes from the TV speakers.
selected.
correctly and securely to your TV.
connected correctly and securely. See
"Connecting a cable or satellite box" on page
or "Connecting an antenna or cable TV (no
on page 13.
signal may be low. To check the digital channel
signal strength, see "Checking the digital signal
strength" on page 30.
a new set.
reflecting off the screen can make the picture
difficult to see.
while another connected device is turned on,
the picture may be poor. Turn off one or more
devices.
Adjust the contrast, color, and brightness
settings. See "Adjusting the TV picture" on
page 24.
receiver, external speakers, fans, or hair dryers)
may be interfering with your TV. Try turning off
one device at a time to determine which device
is causing interference. After you have
determined which device is causing
interference, move it further from the TV to
eliminate the interference.
www.insigniaproducts.com
Problem
No output from one of the
speakers.
10
box)"
After images appear.

Remote control

Problem
Remote control does not
work.
Trouble programming your
existing universal remote
control.
10
box)"

General

Problem
No power.
"No signal" error
message is displayed.
Solution
• Adjust the audio balance. See
settings" on page 26.
• Make sure that the audio cables are connected
correctly and securely to your TV.
• Do not display a still image, such as a logo,
game, or computer image, for an extended
period of time. This can cause a permanent
after-image to be burned into the screen. This
type of damage is not covered by your warranty.
Solution
• Make sure that the power cord is correctly
connected to your TV and a power outlet.
• Make sure that there are no obstructions
between the remote control and the remote
control sensor on the front of the TV.
• Point the remote control directly at the remote
control sensor on your TV. For the location of the
remote control sensor, see "Aiming the remote
control" on page 20.
• The supplied batteries are wrapped tightly in
clear plastic. Make sure that you have removed
this plastic from the batteries.
• Make sure that the batteries are installed
correctly. See "Installing remote control
batteries" on page 20.
• Replace dead batteries with new batteries. See
"Installing remote control batteries" on page 20.
• See instructions and a table of common codes in
"Programming a different universal remote
control" on page 49.
• Codes are subject to change. For up-to-date
codes, go to
www.insigniaproducts.com/remotecodes
• Replace dead batteries with new batteries. See
"Installing remote control batteries" on page 20.
• Refer to the User Guide that accompanied your
universal remote control and contact the
manufacturer if problems persist.
Solution
• Make sure that the power cord is correctly
connected to your TV and a power outlet.
• Unplug the power cord, wait 60 seconds, then
plug the cord back in and turn on your TV.
• Other devices (for example, a surround sound
receiver, external speakers, fans, or hair dryers)
may be interfering with your TV. Try turning off
one device at a time to determine which device
is causing interference. After you have
determined which device is causing
interference, move it further from the TV to
eliminate the interference.
• Press INPUT and make sure that you have
selected the correct input for the device or
service you are trying to use.
• If you are using a cable or satellite box, use the
remote that came with that box to change
channels.
• Make sure that you have the correct input
selected to view channels from the cable or
satellite box.
"Adjusting sound
47