Table of Contents
Advertisement
Quick Links
WASHER INSTALLATION INSTRUCTIONS
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
W10038090
WASHER SAFETY............................................ 1
INSTALLATION REQUIREMENTS ................. 2
Tools and Parts ............................................. 2
Location Requirements................................. 2
Drain System................................................. 3
Electrical Requirements ................................ 3
INSTALLATION INSTRUCTIONS ................... 4
Before You Start............................................ 4
Remove Shipping Materials.......................... 4
Connect Drain Hose...................................... 5
Connect the Inlet Hoses ............................... 6
Secure the Drain Hose.................................. 7
Level the Washer........................................... 7
Complete Installation .................................... 8
WASHER SAFETY
Your safety and the safety of others are very important.
Table of Contents
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
Advertisement
Table of Contents
Related Manuals for Whirlpool W10038090
Summary of Contents for Whirlpool W10038090
-
Page 1: Table Of Contents
You can be killed or seriously injured if you don't follow WARNING instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. W10038090... -
Page 2: Installation Requirements
INSTALLATION REQUIREMENTS Alternate Parts Tools and Parts Your installation may require additional parts. For information on ordering, please refer to the toll-free phone numbers on the front Gather the required tools and parts before starting installation. page of the Washer User Instructions. The parts supplied are in the washer basket. -
Page 3: Drain System
Recessed area or closet installation Laundry tub drain system (view C) The dimensions shown are for the recommended spacing allowed The laundry tub needs a minimum 76 L (20 gal.) capacity. The top (A and B), except the closet door ventilation openings. The of the laundry tub must be at least 99 cm (39") above the floor and dimensions shown for the closet door ventilation openings (C) are no higher than 244 cm (96") from the bottom of the washer. -
Page 4: Installation Instructions
To minimize possible shock hazard, the cord must be plugged into a mating, earthing-type outlet, earthed in accordance with EARTHING INSTRUCTIONS local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer For an earthed, cord-connected washer: to have the properly earthed outlet installed by a qualified This washer must be earthed. -
Page 5: Connect Drain Hose
2. Firmly grasp the power cord and pull to completely remove 2. Check that two (2) cotter pins were removed with the shipping the power cord, cord restraint, and pin from the rear panel. strap. 3. Confirm that the power cord restraint (A), and pin (B) are removed. -
Page 6: Connect The Inlet Hoses
To keep drain water from going back into the washer: Check the temperature of the water to make sure that the hot water hose is connected to the hot water faucet and that the Do not force excess drain hose into standpipe. Hose should cold water hose is connected to the cold water faucet. -
Page 7: Secure The Drain Hose
5. Attach the cold water hose to the top inlet valve. Level the Washer 6. Screw on coupling by hand until it is seated on the washer. 7. Using pliers, tighten the couplings with an additional Properly leveling your washer avoids excessive noise and two-thirds turn. -
Page 8: Complete Installation
Close the lid. Select any cycle, and then pull the cycle control knob out to start the washer. Allow it to complete one whole cycle. W10038090 4/06 © 2006 Whirlpool Corporation. Benton Harbor, Michigan 49022 Printed in U.S.A.