Advertisement
2
Remove
cooktop
burner
grates
.
and
caps
oackaae
from
shipping
box.
Remove
p?essure
regulator
ond
hardware
package
from
side of carton.
Property
Damage
Lift entire
cookiop
up from
cutout
when
repositioning
cooktop
in
counterlop
opening.
Failure
to do so could
scratch
countertop.
lnse:
the cooktop
into the countertop
cutout.
Center
the
cooktop
rn the
cutout.
Check
that
the
front
of the
cookiop
is parallel
to the front
edge
of the countertop
Check
that
all
required
clearances
are met
If
cooktop
is not properly
posltioned,
lift the
entire
cooktop
out of opening
to moke
adjustments
so that
foam
sealrng
strrp can
seal
properly
4.
instoll
the pressure
regulator
wth
the
arrow
on the
regulator
pointing
up
toward
the unit
and
in position
where
you
can
reach
ihe
access
cop.
Fire Hazard
Do Not make
connection
too tight
The regulator
is die cost.
Overtightening
may
crack
regulator
resulting
in a gas leak
and
possible
fire or explosion.
5
Assimble
the
flexrble
connector
from
the Qas supply
pipe
to the pressure
regulator
in this order
manual
shuioff
valve.
112 nrpple.
l/2"
adapter,
flexible
connector,
l/2'
adapter
and
l/2"
nipple
All connections
must
be
wrench
lightened.
6.
Use pope-Joint
compound
made
for
use wrth
NATURAL
and
L P Qas to seal
all gas connections
If flexible
connectors
are used,
be certarn
connecton
are not kinked
7
Open
the shutoff
valve
in the
n
gas supply
line.
Walt
0 few
minutes
for the gas to move
through
the
QOS line
Fire Hazard
Do Not use an open
flame
to test for
leaks
from
gas connections.
Checking
for leaks
with
o flame
may
result
in 0 fire, explosion
or
personal
injury.
8
Use o brush
and
liquid
.
detergent
to test all gas
connectrons
for leaks
Bubbles
around
the
connectrons
WIII indicate
o leak.
If a leak
appears,
shut off gas
valve
controls
and
adlust
connectors
Then
check
connectlons
ogarn
NEVER TEST FOR GAS LEAKS WITH A
MATCH
OR OTHER OPEN
FLAME.
Clean
oil the
detergent
solutron
from
cooktop.
grounded
outlet
10
Place
trim
rings over
each
.
burner
Make
sure burner
cap
IS properly
OlIQned
and
level
Locate
the tab
on the
burner
cap
and
place
over
the white
electrode
rn the
burner
base
Place
burner
grates
over
burner?
and
cops.
Electronic
ignition
System
-
initial
lighting
Cooktop
burners
use eleCtrOniC
ignrters
1-1 place
of StOndinQ
pilots.
When
the cooktop
control
knob
is
turned
to the
'LITE'
posrtion.
the
system
creates
a spark
to lrght the
burner.
This sparking
COniinUeS
until
the control
knob
is turned
to the
desired
setting.
11
Check
the operation
of the
.
cooktop
burners
Push in
and
turn
each
control
knob
lo "NE'
posItron
The flame
should
light
within
4 seconds.
Do Not leave
the knob
in
the IITE'
position
after
burner
lights.
If the
burners
do not light
property.
turn
the control
knob
to the
"OFF"
positIon.
Check
that
the burner
cop
is
In the
proper
position.
Check
that
the
power
cord
is plugged
In and
that
the
circuit
breaker
or fuse has not blown.
Check
that
the shutoff
valve
is in the
'ON'
positron.
Check
operotlon
again
If burner
does
not IkQht at this point.
contact
your
Whrrlpool
deoler
for
assrstance
12
After
burner
lights.
turn
-
control
to 'HI" position.
Check
each
cooktop
burner
for
proper
flame.
The small
inner
cone
should
have
o very
drstinct
blue
flame
opprodmotety
l/Z'
long.
The
outer
cone
is not as distinct
OS the
inner
cone.
The 'LO'
(or simmer)
sening
on each
burner
has been
factory
set to the
lowest
settrng
ovalIable.
If any
burner
does
not stay
lit at the
'LO'setting.
contact
your
Whirlpool
dealer
for assistance.
Numbers
correspond
to sleps.
'ANEL
C
Advertisement
