Universal Remote Control Easy Clicker UR3L-SR4 Operating Manual

1 3
Operating Manual Introduction Button Functions
This remote control is designed
For Easy Clicker
to operate most IPTV and DTA
STBs as well as Digital and
UR3L-SR4 Analog Cable Boxes.
2
Replacing Batteries
Before you program or operate the
remote control, you must install
two new AAA alkaline batteries.
STEP1 Remove the battery com-
partment cover from the
back of your remote control.
STEP2 Check battery polarity
carefully, and install the
batteries as shown in the
illustration below.
STEP3 Replace the battery
compartment cover.
4
Programming the Remote Control
*Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either the
CBL, TV, or DVD button, depending on which device you are programming the remote to operate.
A. Quick Set-Up Method A. Quick Set-Up Method
Universal Remote Control, Inc.
STEP1 Turn on the equipment you want toprogram. To program your TV, turn on the TV.
www.universalremote.com
STEP2 Point the remote at the component andpress and hold the [DEVICE] key for 5seconds until the Device LED blinks
OCE-0082B REV 10 (06/08/12)
The equipment should turn The equipment should turn
off and turns back on. Continue hold-
back on. Then try all of the back on. Then try all of the
ing the [DEVICE] key and press the
numberkeys, one at a time, starting functions on the remote control functions on the remote control
with 1, then2, 3...0. Stop pressing the (i.e. volume, mute, etc.) to (i.e. volume, mute, etc.) to
number keys when the device turns ensure you have the correct ensure you have the correct
off. code. If any of the functions do code. If any of the functions do
not operate as they should, not operate as they should,
STEP3 Release the [DEVICE] key to
repeat the instructions from repeat the instructions from
save the code. The Device
STEP 3 above using the next STEP 3 above to continue the
LED will blink twice to confirm
three digit code number from Auto Search Method.
the code is stored.
the brand list.
STEP4 Press the same [DEVICE]
Repeat the steps above for all components
button to store the code. The
STEP4 Store the three-digit code by
(CBL, TV, DVD).
pressing the same [DEVICE] Device LED will blink twice
B. B. Manual Manual Pr Programming ogramming
button once again. The device to confirm that the code has
LED will blink twice to confirm been stored.
The remote control can be programmed
that the code has been stored.
by entering a three-digit code number
D. D. T T o find the o find the Thr
that corresponds to particular brands
C. C. Auto Auto Sear Search Method ch Method
that that W Was Pr
and models of equipment. The three-
the Auto
the Auto Sear
If none of the three digit code numbers
digit code numbers are listed in the
assigned to your brand of equipment works,
code tables sections of this instruction
STEP1 Press the appropriate [DEVICE]
or the code table does not list your brand,
manual.
button and the [OK/SEL] button
you can use the Auto Search Method to
simultaneously for three seconds.
STEP1 Turn on the equipment that you
find the correct three-digit code number for
The device LED will turn on for
want the remote control to
your equipment by following steps:
30 seconds. The next step
operate (Cable Box, TV or DVD) .
must be performed while the
STEP1 Turn on the equipment that you
STEP2 Press the [DEVICE] button and LED is on.
want the remote control to
the [OK/SEL] button simultane-
operate (Cable Box, TV or DVD).
STEP2 Press the [INFO] button. The
ously for three seconds. The
device LED will blink a number
STEP2 Press the [DEVICE] button and
corresponding device LED will
the [OK/SEL] button simulta- of times indicating the number
turn on indicating that it is ready
of each digit for the code. Each
to be programmed. The LED will neously for three seconds.
remain on for 30 seconds. The The device LED will turn on digit is separated by a one second
indicating that it is ready to be interval of the LED being off.
next step must be entered while
programmed. The LED will
the LED is on.
Example : One blink, then three blinks,
remain on for 30 seconds. The
STEP3 Point the remote control
then eight blinks indicates
next step must be entered
toward the equipment and the code number 138.
while the LED is on.
enter the three-digit code
*Note : Ten blinks indicates the number 0.
STEP3 Press the [CH ] or [CH ] button
number assigned to your
one at a time or keep it
brand from the code tables.
E. E. Pr Pr ogramming a Second ogramming a Second
If there are more than one pressed. The remote will emit
TV to the DVD Button
TV to the DVD Button
three-digit number listed for a series of Power ON/OFF
your brand, try one code code signals. Release the
STEP1 Press the [DVD] button and
[CH ] or [CH ] button as soon
number at a time until your
the [OK/SEL] button simultane-
as the equipment turns off.
equipment turns off.
ously for 3 seconds. The DVD
*Note: You can verify that you have *Note: You can verify that you have
LED will turn on for 30 seconds.
selected the correct code by selected the correct code by
The next step must be performed
pressing the [POWER] button.
pressing the [POWER] button.
while the LED is on.
STEP2 Press the [TV] button. G. G. Erasing a Single Erasing a Single Lear
Command Command
STEP3 Point the remote control
toward the TV and enter the
STEP1 Press the [Device] and [INPUT]
three-digit code for your TV
buttons simultaneously for 3
from the TV codes table.
seconds until the Device LED
light turns on.
STEP4 Store the three-digit code by
pressing the [DVD] button.
STEP2 Press and hold the button you
The device LED will blink
want to erase for 3 seconds.
twice to confirm that the
The Device LED will blink
code has been stored.
twice to confirm the erasure.
F . The Learning Method ning Method
F . The Lear
STEP3 To exit, press and hold both the
[Device] and [INPUT] buttons
STEP1 Press the [Device] button
simultaneously until the Device
(CBL, TV or DVD) to be
LED blinks 3 times.
programmed and the [INPUT]
Three-Digit Code ee-Digit Code
buttons simultaneously for 3
H. Erasing All Learned Commands ned Commands
H. Erasing All Lear
as Programmed using ogrammed using seconds until the Device LED
fr from One Device om One Device
light turns on.
Search Method ch Method
STEP1 Press the [DEVICE] and
STEP2 Line up the UR3L-SR4 to the
[INPUT] buttons simultane-
other remote, head-to-head,
ously for 3 seconds until the
1 or 2 inches apart.
Device LED light turns on.
STEP3 Press any button on the UR3L-
STEP2 Press and hold both the
SR4 that you want to teach a
[DEVICE] button you want to
command to. For example, if
erase and the [PAUSE] button
you want to teach the [MUTE]
for 5 seconds. The Device LED
button, press the [MUTE] button.
will blink twice to confirm the
erasure.
STEP4 Press and hold the [MUTE]
button on the other remote
STEP3 To exit, press and hold both the
until the UR3L-SR4 Device LED
[DEVICE] and [INPUT] buttons
light blinks twice.
simultaneously until the Device
LED blinks 3 times.
*Note : The LED will blink 5 times if there
was an error in the learning
I. Programming the All Of ogramming the All
I. Pr
process. In so, repeat STEPS 3 and
4. Continue learning other buttons This allows you to program the All Off
by repeating STEPS 3 and 4. button so it can send up to three power
On/Off commands with one button press.
STEP5 Once you have completed
teaching UR3L-SR4 all desired STEP1 Press the [CBL] button.
commands for that Device,
STEP2 Press the [All OFF] button and the
save the learned commands
[OK/SEL] button simultaneously
by pressing the [Device] and
for 3 seconds. The [CBL] button
[INPUT] buttons simultane-
will turn on for 30 seconds.
ously until the Device LED
blinks 3 times. Now test all the STEP3 Press the first [Device] button
buttons to make sure they you want to store in the [ALL OFF]
learned correctly. button and then the [POWER]
Learned ned button. Repeat this for other To access the programmed channels,
Device until you have stored all press the [MACRO] button once. This
the desired power commands will bring up the first channel. Press
into the [ALL OFF] button. once again and it will bring up the
second channel. Press again and it
STEP4 Press the [CH ] button to save
will bring up the third channel.
the power commands you
stored. The [CBL] button will To erase the Macro programming
blink twice to confirm the and return to the original function:
Device have been saved.
STEP1 Press the [CBL] button to
J. J. Pr Programming for ogramming for select the CABLE mode.
Advanced Functions.
Advanced Functions.
STEP2 Press a [MACRO] button and the
[OK/SEL] button simultaneously
If your remote model has custom-
for 3 seconds. The CBL device
programmable Macro buttons available,
they can be programmed to act as a LED will turn on for 30 seconds.
'Macro' or Favorite Channel button in The next step must be performed
CABLE mode. This allows you to program
while the LED is on.
up to five 2-digit channels, four 3-digit
STEP3 Press the [CH ] button to
channels or three 4-digit channels that
erase the functions stored in
can be accessed With one button press.
the button. The CBL device
*Note : The FAV button is not
LED will blink twice to confirm
programmable if you have a
that the memory button has
Digital Cable Box made by
been erased.
Pace, Pioneer or CISCO/SA.
K. Pr K. Programming V ogramming Volume Contr olume Control ol
STEP1 Press the [CBL] button to
select the CBL mode.
Volume and Mute control are factory-
STEP2 Press the [MACRO] button and programmed to automatically transfer
[OK/SEL] button simultaneously
to the respective Device mode you
for 3 seconds. The [CBL] button
select, as follows:
will turn on for 30 seconds.
CBL : TV TV : TV DVD : TV
STEP3 Enter the the 2, 3 or 4-digit
code for the channel you want
If you wish to store the Cable volume
programmed first (for example,
Off Button f Button control in CBL mode, use the following steps.
007) using the Number Pad,
STEP1 Press the [OK/SEL] button and
then press the [STOP] button.
Then enter the code for the
[CBL] button simultaneously for
next channel (for example,
three seconds. The device LED
050), then press the [STOP]
will turn on for 30 seconds. The
button. Repeat this process for
next step must be performed
the third channel. The [CBL]
while the LED is on.
button will blink once for each
channel entered.
STEP2 Press the [VOL ] button.
The device LED will blink.
STEP4 Press the [CH ] button to
store the channels that were
STEP3 Press [CBL] button. The
selected. The [CBL] button
device LED will blink twice
will blink twice to confirm
to confirm the programming.
the storage of commands.
Note : To return CBL device to TV
volume repeat steps above
replacing [CBL] with [TV] in
Step 3.
L. L. Pr Programming Channel Contr ogramming Channel Control ol
Channel controls are factory-programmed
to automatically transfer to the respective
Device mode you select, as follows:
CBL : CBL TV : CBL DVD : DVD
If you wish to store the TV channel
controls in TV mode, use the following
steps.
STEP1 Press the [OK/SEL] button and
[TV] button simultaneously for
three seconds. The device LED
will turn on for 30 seconds. The
next step must be performed
while the LED is on.
STEP2 Press the [VOL ] button. The
device LED will blink.
STEP3 Press [TV] button. The device
LED will blink twice to confirm
the programming.
Note : To return TV device to CBL
channel repeat steps above
replacing [TV] with [CBL]
in Step 3.
M. Low Battery W y War arning ning
M. Low Batter
When the battery is low (2.3V-2.0V) and
needs to be replaced with fresh batteries,
device LED will blink 2 times in sequence
whenever a [DEVICE] button is pressed
to turn on equipment.
N. Memory Lock System. y Lock System.
N. Memor
This remote control is designed to
retain programmed memory for 10
years — even after batteries are
removed from the remote control.
For additional information about your
remote control, go to www.universal-
remote.com