Universal Remote Control UR3L-SR4 Operating Manual

Operating Manual
1 Introduction 3 Button Functions
This remote control is designed
For Easy Clicker
to operate most Digital and
Analog Cable Boxes, as well as
UR3L-SR4 TVs, and a VCR or DVD player.
2 Replacing Batteries
Before you program or operate the
remote control, you must install
two new AAA alkaline batteries.
STEP1 Remove the battery com-
partment cover from the
back of your remote control.
STEP2 Check battery polarity
carefully, and install the
batteries as shown in the
illustration below.
STEP3 Replace the battery
compartment cover.
4 Programming the Remote Control
*Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either the
CBL, TV, or DVD button, depending on which device you are programming the remote to operate.
A. A. Manual Pr Manual Programming ogramming
Universal Remote Control, Inc.
The remote control can be programmed by entering a three-digit code number that corresponds to particular brands
www.universalremote.com
and models of equipment. The three-digit code numbers are listed in the code tables sections of this instruction manual.
OCE-0082B REV 02 (08/18/10)
STEP1 Turn on the equipment that you B. B. Auto Auto Sear Search Method ch Method C. C. T T o find the o find the Thr
want the remote control to
that W that Was Pr as
If none of the three digit code numbers
operate (Cable Box, TV or DVD) .
the Auto Sear the Auto
assigned to your brand of equipment works,
or the code table does not list your brand,
STEP2 Press the [DEVICE] button and
STEP1 Press the appropriate [DEVICE]
you can use the Auto Search Method to
the [OK/SEL] button simultane-
button and the [OK/SEL] button
find the correct three-digit code number for
ously for three seconds. The
your equipment by following steps: simultaneously for three seconds.
corresponding device LED will
The device LED will turn on for
turn on indicating that it is ready STEP1 Turn on the equipment that you
30 seconds. The next step
to be programmed. The LED will want the remote control to
must be performed while the
remain on for 30 seconds. The operate (Cable Box, TV or DVD).
LED is on.
next step must be entered while
STEP2 Press the [DEVICE] button and
the LED is on.
STEP2 Press the [INFO] button. The
the [OK/SEL] button simulta-
device LED will blink a number
neously for three seconds.
STEP3 Point the remote control
The device LED will turn on of times indicating the number
toward the equipment and
indicating that it is ready to be of each digit for the code. Each
enter the three-digit code
programmed. The LED will
digit is separated by a one second
number assigned to your
remain on for 30 seconds. The
interval of the LED being off.
brand from the code tables.
next step must be entered
If there are more than one
while the LED is on. Example : One blink, then three blinks,
three-digit number listed for
then eight blinks indicates
STEP3 Press the [CH ] or [CH ] button
your brand, try one code
the code number 138.
one at a time or keep it
number at a time until your
pressed. The remote will emit
*Note : Ten blinks indicates the number 0.
equipment turns off.
a series of Power ON/OFF
code signals. Release the D. D. Pr Programming a Second ogramming a Second
*Note: You can verify that you have
[CH ] or [CH ] button as soon
selected the correct code by TV to the DVD Button TV to the DVD Button
as the equipment turns off.
pressing the [POWER] button.
STEP1 Press the [DVD] button and
The equipment should turn
*Note: You can verify that you have
the [OK/SEL] button simultane-
back on. Then try all of the
selected the correct code by
ously for 3 seconds. The DVD
functions on the remote control
pressing the [POWER] button.
LED will turn on for 30 seconds.
(i.e. volume, mute, etc.) to The equipment should turn
The next step must be performed
ensure you have the correct back on. Then try all of the
while the LED is on.
functions on the remote control
code. If any of the functions do
(i.e. volume, mute, etc.) to
not operate as they should,
STEP2 Press the [TV] button.
ensure you have the correct
repeat the instructions from
code. If any of the functions do
STEP3 Point the remote control
STEP 3 above using the next
not operate as they should,
toward the TV and enter the
three digit code number from
repeat the instructions from
three-digit code for your TV
the brand list.
STEP 3 above to continue the
from the TV codes table.
Auto Search Method.
STEP4 Store the three-digit code by
STEP4 Store the three-digit code by
pressing the same [DEVICE]
STEP4 Press the same [DEVICE]
pressing the [DVD] button.
button once again. The
button to store the code. The
The device LED will blink
device LED will blink twice Device LED will blink twice
to confirm that the code has twice to confirm that the
to confirm that the code has
been stored. been stored. code has been stored.
Three-Digit Code ee-Digit Code E. E. The Lear The Learning Method ning Method STEP2 Press and hold the button you
want to erase for 3 seconds.
Programmed using ogrammed using
STEP1 Press the [Device] button
The Device LED will blink
Search Method ch Method
(CBL, TV or DVD) to be
twice to confirm the erasure.
programmed and the [INPUT]
STEP3 To exit, press and hold both the
buttons simultaneously for 3
[Device] and [INPUT] buttons
seconds until the Device LED
simultaneously until the Device
light turns on.
LED blinks 3 times.
STEP2 Line up the UR3L-SR4 to the
G. Erasing All Learned Commands ned Commands
G. Erasing All Lear
other remote, head-to-head,
fr from One Device om One Device
1 or 2 inches apart.
STEP3 Press any button on the UR3L- STEP1 Press the [DEVICE] and
SR4 that you want to teach a [INPUT] buttons simultane-
ously for 3 seconds until the
command to. For example, if
Device LED light turns on.
you want to teach the [MUTE]
button, press the [MUTE] button.
STEP2 Press and hold both the
[DEVICE] button you want to
STEP4 Press and hold the [MUTE]
erase and the [PAUSE] button
button on the other remote
for 5 seconds. The Device LED
until the UR3L-SR4 Device LED
will blink twice to confirm the
light blinks twice.
erasure.
*Note : The LED will blink 5 times if there
STEP3 To exit, press and hold both the
was an error in the learning
[DEVICE] and [INPUT] buttons
process. In so, repeat STEPS 3 and
simultaneously until the Device
4. Continue learning other buttons
LED blinks 3 times.
by repeating STEPS 3 and 4.
H. H. Pr Programming the All Of ogramming the All
STEP5 Once you have completed
teaching UR3L-SR4 all desired
This allows you to program the All Off
commands for that Device,
button so it can send up to three power
save the learned commands
On/Off commands with one button press.
by pressing the [Device] and
STEP1 Press the [CBL] button.
[INPUT] buttons simultane-
ously until the Device LED
STEP2 Press the [All OFF] button and the
blinks 3 times. Now test all the
[OK/SEL] button simultaneously
buttons to make sure they for 3 seconds. The [CBL] button
learned correctly. will turn on for 30 seconds.
STEP3 Press the first [Device] button
F F . . Erasing a Single Lear Erasing a Single Learned ned
you want to store in the [ALL OFF]
Command Command
button and then the [POWER]
STEP1 Press the [Device] and [INPUT] button. Repeat this for other
buttons simultaneously for 3 Device until you have stored all
seconds until the Device LED the desired power commands
light turns on. into the [ALL OFF] button.
STEP4 Press the [CH ] button to save To access the programmed channels,
press the [MACRO] button once. This
the power commands you
will bring up the first channel. Press
stored. The [CBL] button will
once again and it will bring up the
blink twice to confirm the
second channel. Press again and it
Device have been saved.
will bring up the third channel.
I. I. Pr Programming for ogramming for
To erase the Macro programming
Advanced Functions. Advanced Functions.
and return to the original function:
If your remote model has custom-
STEP1 Press the [CBL] button to
programmable Macro buttons available,
select the CABLE mode.
they can be programmed to act as a
'Macro' or Favorite Channel button in STEP2 Press a [MACRO] button and the
[OK/SEL] button simultaneously
CABLE mode. This allows you to program
for 3 seconds. The CBL device
up to five 2-digit channels, four 3-digit
LED will turn on for 30 seconds.
channels or three 4-digit channels that
The next step must be performed
can be accessed With one button press.
while the LED is on.
*Note : The FAV button is not
STEP3 Press the [CH ] button to
programmable if you have a
erase the functions stored in
Digital Cable Box made by
the button. The CBL device
Pace, Pioneer or CISCO/SA.
LED will blink twice to confirm
STEP1 Press the [CBL] button to
that the memory button has
select the CBL mode.
been erased.
STEP2 Press the [MACRO] button and
J. Pr J. Programming V ogramming Volume Contr olume Control ol
[OK/SEL] button simultaneously
Volume and Mute control are factory-
for 3 seconds. The [CBL] button
programmed to automatically transfer
will turn on for 30 seconds.
Off Button f Button to the respective Device mode you
STEP3 Enter the the 2, 3 or 4-digit
select, as follows:
code for the channel you want
CBL : TV TV : TV DVD : TV
programmed first (for example,
007) using the Number Pad,
If you wish to store the Cable volume
then press the [STOP] button.
control in CBL mode, use the following steps.
Then enter the code for the
STEP1 Press the [OK/SEL] button and
next channel (for example,
[CBL] button simultaneously for
050), then press the [STOP]
three seconds. The device LED
button. Repeat this process for
will turn on for 30 seconds. The
the third channel. The [CBL]
next step must be performed
button will blink once for each
while the LED is on.
channel entered.
STEP2 Press the [VOL ] button.
STEP4 Press the [CH ] button to
The device LED will blink.
store the channels that were
selected. The [CBL] button
STEP3 Press [CBL] button. The
will blink twice to confirm device LED will blink twice
the storage of commands.
to confirm the programming.
Note : To return CBL device to TV
volume repeat steps above
replacing [CBL] with [TV] in
Step 3.
K. K. Pr Programming Channel Contr ogramming Channel Control ol
Channel controls are factory-programmed
to automatically transfer to the respective
Device mode you select, as follows:
CBL : CBL TV : CBL DVD : DVD
If you wish to store the TV channel
controls in TV mode, use the following
steps.
STEP1 Press the [OK/SEL] button and
[TV] button simultaneously for
three seconds. The device LED
will turn on for 30 seconds. The
next step must be performed
while the LED is on.
STEP2 Press the [VOL ] button. The
device LED will blink.
STEP3 Press [TV] button. The device
LED will blink twice to confirm
the programming.
Note : To return TV device to CBL
channel repeat steps above
replacing [TV] with [CBL]
in Step 3.
L. Low Battery W y War arning ning
L. Low Batter
When the battery is low (2.3V-2.0V) and
needs to be replaced with fresh batteries,
device LED will blink 2 times in sequence
whenever a [DEVICE] button is pressed
to turn on equipment.
M. Memory Lock System. y Lock System.
M. Memor
This remote control is designed to
retain programmed memory for 10
years — even after batteries are
removed from the remote control.
For additional information about your
remote control, go to www.universal-
remote.com