Introduction This remote control is designed to operate most Digital and Analog Cable Boxes, as well as TVs, and a VCR or DVD player. Replacing Batteries Before you program or operate the remote control, you must install two new AAA alkaline batteries. STEP1 Remove the battery compartment cover from the back of your remote control.
Button Functions Programming the Remote Control. *Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either the CBL, TV, or DVD button, depending on which device you are programming the remote to operate. A.
Page 5
LED blinks off and turns back on. Continue holding the [DEVICE] key and press the number keys, one at a time, starting with 1, then2, 3...0. Stop pressing the number keys when the device turns off. STEP3 Release the [DEVICE] key to save the code. The Device LED will blink twice to confirm the code is stored.
three-digit code number from the same brand list. C. Auto Sear ch Method C. Auto Sear ch Method If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps:...
Page 7
digit for the code. Each digit is separated by a one second interval of the LED being off. Example : One blink, then three blinks, then eight blinks indicates the code number 138. *Note : Ten blinks indicates the number 0. ogramming a Second TV to the DVD Button ogramming a Second TV to the DVD Button STEP1...
Page 8
process for the third channel. The [CBL] button will blink once for each channel entered. STEP4 Press the [CH ] button to store the channels that were selected. The [CBL] button will blink twice to confirm the storage of commands. To access the programmed channels, press the [MACRO] button once.
Page 9
operate your Cable Box, press the [CBL] button in Step3. Assigning the Channel keys to a Assigning the Channel keys to a ent Device ent Device By default, the CH+, CH-, NUMERIC and LAST keys operate through your Cable Box. If you would like those keys to operate those functions on a different device, follow these steps.
Page 10
Quick Set-up Code Tables Manufacturer/Brand Quick Number PACE SCIENTIFIC ATLANTA/CISCO, PACE, SAMSUNG MOTOROLA AMINO AT&T CISCO DIRECTV MOXI TIVO HUMAX Manufacturer/Brand Quick Number SANYO SONY SAMSUNG TOSHIBA PANASONIC PHILIPS HITACHI SHARP VIZIO Manufacturer/Brand Quick Number HITACHI SONY PHILIPS SAMSUNG PHILIPS MAGNAVOX PANASONIC DENON PIONEER...
Set-up Code Tables CABLE TV CONVERTER CODE No MAKER(BRAND) NAME CISCO/SA EXPLORER Series 001 007 8600X 8600 8540,8570,8590 8500 IPN Series MOTOROLA DCT Series (DVR Model) VIP Series GENERAL INSTRUMENT DCT Series,DCH Series, CFT2200 DL4,DQNV/DRX,DPBB,DPV/DP/DQN,DRZ 027 JERROLD BMC9012/BMC9022 DSR470 CFT2000 DL4,DP(V),DQN(V),DPBB Some Model DL4,DQNV/DRX,DPBB,DPV/DP/DQN,DRZ 027...
Page 12
CABLE TV CONVERTER CODE No MAKER(BRAND) NAME NFUSION NUVENIO SD PHOENIX, NUVENIO HD, SOLARIS, NOVA NOW TV NOWTV IM781R IM781 SIGMAONE, P1,P2,P3, SIGMA 2000 RTC56,RKDM SIGMA 2001,2002 SIGMA 450,500,550 PACE 500 Series 001 007 TDC Series DTA Series PANASONIC 140,145,170,175 110,120,130,150,160 PIONEER VOYAGER Series...