Universal Remote Control CLIKR-5 UR5L-8720L Operating Instructions

1 4
Introduction Button Functions
Operating Instructions For
The CLIKR TM -5 UR5L-8700L & UR5L-8720L
CLIKR ™ -5
are designed to operate the Scientific-
Atlanta, Pioneer, Pace Micro, Samsung and
Motorola digital set tops, plus the majority
Cable Remote Control
of TV, VCR, DVD and AUDIO equipment on
the market as shown below.
CABLE : Cable Converters TV : Televisions
UR5L-8700L & UR5L-8720L
VCR : VCRs and TV/VCRs DVD: DVD Players
AUX : Audio Receivers and DVRs, etc.
2
Replacing Batteries
Before you program or operate the remote con-
trol, you must install two new AA alkaline batter-
ies.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
3
Operations 5
Programming the Remote Control
DEFAULT STATE: There are two ways you can program your CLIKR
Component Default: CABLE Set Top Box (STB)
* The Pre-Programmed 3-Digit Code Method
Channel Default: CABLE channel and numbers * The Auto-Search Method
* The Learning Method
through the CABLE STB. You have the option of
controlling your CABLE channel and numbers The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit
through the TV or VCR. Refer to section I for pro- code numbers that correspond to a particular Component's manufacturer/brand, so it's the fastest
and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The
gramming steps.
Auto-Search Method scans through all the codes in the remote control, one at a time. The
Volume Default: Volume and Mute control are
Learning Method allows you to transfer functions from other remotes, one button at a time.
automatically transferred to the respective
IMPORTANT SETUP NOTE!
Component mode you select, as follows: CBL:
This pertains to all programming steps. When you are in setup mode, a component LED will light
Cable Set Top Box / TV: TV / AUX: AUX. Volume
for 30 seconds.If you do not press a button within 30 seconds, the LED light will turn off and exit
and Mute control for VCR and DVD are automat-
setup mode and you will need to start over.
Universal Remote Control, Inc. ically transferred to the TV. However, you have
the option of controlling CABLE Volume and A. Pre-Programmed 3-Digit Code Method
www.universalremote.com
Mute through the TV, VCR or AUX. Refer to sec-
OCE-0060F REV 12 (08/17/11)
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX).
tion J for programming steps.
STEP2 Press the [COMPONENT] button (TV, Now, repeat the Auto-Search Method for those
VCR, DVD or AUX) to be programmed
Components you could not program earlier
and [OK/SEL] button simultaneously for with the Pre-Programmed Method.If you can't
3 seconds. The Component LED light will
find the right code using the Auto-Search
turn on for 30 seconds indicating the
Method, try the Learning Method in Section C.
unit is ready to be programmed.
C. The Learning Method
STEP3 Point the remote control toward the
Component and enter the 3-digit code
STEP1 Press the [COMPONENT] button
number assigned to your brand.
(TV,VCR,DVD or AUX) to be pro-
*Note : If the 3-digit code number you just grammed and the [ASPECT] buttons
entered is correct, the Component will simultaneously for 3 seconds until the
turn Off. If it did not turn Off, continue
Component LED light turns on.
entering code numbers listed for that
STEP2 Line up the CLIKR
brand until the Component turns Off.
head-to-head, 1 or 2 inches apart.
STEP4 After you've entered the correct code
STEP3 Press any button on the CLIKR
number and the Component has turned
you want to teach a command to. For
Off, press the [POWER] button to turn the
example, if you want to teach the
Component back On. Now it is time to
[MUTE] button, press the [MUTE] but-
test the VOLUME and MUTE buttons for
ton.
the TV (or PLAY and STOP buttons for
VCR and DVD) to make sure they all work.
STEP4 Press and hold the [MUTE] button on
If any of the functions do not work as they
the other remote until the CLIKR
should, repeat from STEP 3 using the next
Component LED light blinks twice.
3-digit code number listed for that brand
until you find the best Component code.
*Note : The LED will blink 5 times if there
was an error in the learning
STEP5 Once you have found the correct 3-digit
code, save it by pressing the same process. In so, repeat STEPS 3 and
[COMPONENT] button one more time. 4. Continue learning other buttons
The Component LED light will blink
by repeating STEPS 3 and 4.
twice to confirm that the code was suc-
STEP5 Once you have completed teaching
cessfully stored.
CLIKR TM
Now, program the rest of your Components
Component, save the learned commands
by repeating STEPS 1-5.
by pressing the [COMPONENT] and
[ASPECT] buttons simultaneously until
*Note : If the Pre-Programmed Method did not
the Component LED blinks 3 times. Now
work, or if the Code Tables do not list
test all the buttons to make sure they
your Component brand, use the Auto-
Search Method as explained in Section B. learned correctly.
D. Erasing a Single Learned Command
B. Auto-Search Method
STEP1 Press the [COMPONENT] and [ASPECT]
STEP1 Turn on the Component you want to
buttons simultaneously for 3 seconds
program (TV, VCR, DVD or AUX).
until the Component LED light turns on.
STEP2 Press the [COMPONENT] button (TV,
VCR, DVD or AUX) to be programmed STEP2 Press and hold the button you want to
erase for 3 seconds. The Component LED
and [OK/SEL] button simultaneously for
3 seconds. The Component LED light will blink twice to confirm the erasure.
TM -5 remote:
will turn on for 30 seconds indicating
STEP3 To exit, press and hold both the [COM-
the unit is ready to be programmed.
PONENT] and [ASPECT] buttons simul-
STEP3 Point the remote toward the Component taneously until the Component LED
blinks 3 times.
and press the [CH ] or [CH ] button one
step at a time or keep it pressed. The
E. Erasing All Learned Commands
remote will emit a series of ON/OFF com-
mands. Release the [CH ] or [CH ] but- from One Component
ton as soon as the Component turns Off.
STEP1 Press the [COMPONENT] and [ASPECT]
STEP4 Test functions. (Same as for 3-Digit Code
buttons simultaneously for 3 seconds
Programming Method - Section A). If any
until the Component LED light turns on.
of the functions do not work as they
STEP2 Press and hold both the [COMPONENT]
should, repeat from STEP 3 using [CH ]
button you want to erase and the
or [CH ] buttons to find the correct code.
[PAUSE] button for 5 seconds. The
STEP5 Save the code. (Same as for 3-Digit Code
Component LED will blink twice to con-
Programming Method - Section A).
firm the erasure.
STEP3 To exit, press and hold both the [COMPONENT] H. Programming the System On/Off Button
and [ASPECT] buttons simultaneously until the
This allows you to program the System On/Off
Component LED blinks 3 times.
button so it can send up to five power On/Off
F. Finding a Component Button's
commands with one button press.
Setup Code Number
STEP1 Press the [CBL] button.
If you used either the Auto-Search or Learning
Methods to program a Component, you may not STEP2 Press the [SYSTEM ON/OFF] button
know what the correct code number is. Here is and the [OK/SEL] button simultaneously
for 3 seconds. The [CBL] button will turn
a way for you to identify the code number, so
you can record it for future reference. on for 30 seconds.
STEP1 Press the [COMPONENT] button (TV, STEP3 Press the first [COMPONENT] button you
VCR, DVD or AUX) you want to verify want to store in the [SYSTEM ON/OFF] but-
TM -5 to the other remote, and the [OK/SEL] button simultaneously
ton and then the [POWER] button. Repeat
for 3 seconds. The Component LED light
this for other Components until you have
will turn on for 30 seconds.
stored all the desired power commands into
TM -5 that
the [SYSTEM ON/OFF] button.
STEP2 Press the [INFO] button and count the
number of times the Component LED light
Press the [CH ] button to save the
STEP4
blinks. This number indicates the first
power commands you stored. The
digit of the code, followed by the second
[CBL] button will blink twice to confirm
and third, each separated by a one sec-
the commands have been saved.
ond pause when the LED will turn off.
TM -5
I. Programming Channel Control
*Note : 10 blinks represents the number zero.
You can program the channel controls (Channel
Example : One blink, (pause), eight blinks,
Up, Channel Down, Last and Numbers) from
(pause) and three blinks, indicates
one Component to operate in another
code number 183.
Component mode. Default channel control set-
G. AUX Function: Programming a 5 th
tings on the remote control are as follows:
Component
CBL : CBL T V : CBL
You can take advantage of the AUX function to
DVD: DVD AUX: AUX
program a 5 th Component such as a second
-5 all desired commands for that
TV, VCR, DVD or Audio Component.
If you wish to store the TV channel control in
TV mode, use the following steps.
STEP1 Turn on the 5 th Component you want
to program (TV, VCR, DVD or Audio).
STEP1 Press the [TV] button and the
[OK/SEL] button simultaneously for 3
STEP2 Press the [AUX] button and the
seconds. The [TV] Component LED
[OK/SEL] button simultaneously for 3
will turn on for 30 seconds.
seconds.The [AUX] Component LED
will turn on for 30 seconds.
STEP2 Press the [VOL ] button.
STEP3 Press the [COMPONENT] button you
STEP3 Press the [TV] button again.
want to setup. Point the remote con-
The Component LED will blink twice
trol toward the Component and enter
to confirm the programming.
the 3-digit code number assigned to
your brand.
To return to original state:
*Note : If the 3-digit code number you just
If you wish to restore the CABLE channel con-
entered is the correct number, the
trol in TV mode, repeat the above steps but
Component will turn Off. If it did not
press [CBL] in STEP3 .
turn Off, continue entering code num-
bers listed for that brand until the J. Programming Volume Control
Component turns Off.
Volume and Mute control are factory-programmed to
STEP4 Test functions. (Same as for 3-Digit Code
automatically transfer to the respective Component
Programming Method - Section A). If any
mode you select, as follows:
of the functions do not work as they
should, you need to find a new code. CBL : CBL T V : TV
DVD : TV AUX : AUX
STEP5 Once you have found the correct 3-digit
code, save it by pressing the [AUX] but-
However, you can program the volume controls
ton one more time. The Component
(Volume Up, Volume Down and Mute) from one
LED light will blink twice to confirm the
Component to operate in another Component.
code was stored. Now when you
press the AUX button, all the buttons If you wish to store the TV volume control in CBL
will work with that 5 th Component. mode, use the following steps.
6
STEP1 Press the [CBL] button and the [OK/SEL] but- Set-up Code Tables
ton simultaneously for 3 seconds. The [CBL]
Component LED will turn on for 30 seconds.
CBL-CABLE Converters
STEP2 Press the [VOL ] button.
Manufacturer/Brand Set-Up Code Number
STEP3 Press the [TV] button.
MOTOROLA 002 111 148
The Component LED will blink twice to
PACE 001 005 002
confirm the programming. PIONEER 001 103 034 051 063 076 105
SAMSUNG 001 030
To return to original state:
SCIENTIFIC ATLANTA/CISCO 001 003 041 042 045 046
If you wish to restore the CBL volume control in CBL
TV
mode, repeat the above steps but press [CBL] in STEP3 .
Manufacturer/Brand Set-Up Code Number
K. Programming a 'Macro' button.
A MARK 112 143
If your remote model has custom-programmable Macro ABEX 025
buttons available, they can be programmed to act as a ACCURIAN 036
'Macro' or Favorite Channel button in CABLE mode. This ADMIRAL 072 251 333
ADVENT 247 388
allows you to program up to five 2-digit channels, four 3-
ADVENTURA 002
digit channels or three 4-digit channels that can be
AIKO 103
accessed with one button press.
AKAI 116 146 248 404 405 473 475 323 387 391 615
ALBATRON 017
STEP1 Press the [CBL] button to select the CBL mode.
ALERON 028
STEP2 Press the [MACRO] button and [OK/SEL] AMERICA ACTION 043
button simultaneously for 3 seconds. The AMPRO 073
AMSTRAD 052
[CBL] button will turn on for 30 seconds.
ANAM 043 054 056 080 112
STEP3 Enter the the 2, 3 or 4-digit code for the channel AOC 116 363 112 058 616
you want programmed first (for example, 007) APEX 572
APEX DIGITAL 006
using the Number Pad, then press the [STOP]
AQUAVISION 573 574
button. Then enter the code for the next chan-
ASTAR 477
nel (for example, 050), then press the [STOP]
AUDIOVOX 076 454 388
button. Repeat this process for the third chan-
VCR: CBL
AVENTURA 052
nel. The [CBL] button will blink once for each
AVIELO 627 628
channel entered.
AVION 441
AXION 039
STEP4 Press the [CH ] button to store the channels
BELCOR 116
that were selected. The [CBL] button will blink
BELL&HOWELL 333 072
twice to confirm the storage of commands.
BENQ 423 600
BOXLIGHT 266
To access the programmed channels, press the
BRADFORD 043
[MACRO] button once. This will bring up the BROCKWOOD 116
first channel. Press once again and it will bring BROKSONIC 238
BYDESIGN 031 032
up the second channel. Press again and it will
CANDLE 116 002 003 363
bring up the third channel.
CAPEHART 058
CARY AUDIO DESIGN 266
L. Low Battery Warning
CELEBRITY 001
CENTURION 116
When the batteries are low and need to be replaced
CETRONIC 043
with fresh batteries, the Component LED lights will
CHANGHONG 247
blink 2 times in sequence whenever a [POWER] button
CITIZEN 116 002 003 363 043 258 103 143
is pressed to turn on equipment.
CLARION 043
CLASSIC 043
M. Memory Lock System
CLP CLASSIC 333
COBY 640 641
This remote control is designed to retain pro-
COLORTYME 116
grammed memory for 10 years even after batteries
CONCERTO 363
are removed from the remote control. CONCIERGE 073
CONTEC 043 050 051
N. Record Your Component Set-up Codes
CORNEA 116
CORONADO 143
VCR : TV
TV Set-up Code Number:
CRAIG 043 054
CROSLEY 164
VCR Set-up Code Number:
CROWN 043 143
CURTIS MATHES 116 258 363 143
DVD Set-up Code Number:
CXC 043
AUX Set-up Code Number:
CYBERHOME 015
DAEWOO 363 016 043 044 076 103 114 125 127 143
For additional information about your remote
DAYTRON 363 143
control, go to www.universalremote.com
DELL 320 164 363 618
TV TV
Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number
DIGITAL PROJECTION 570 LITEON 268
DIMENSIA 333 LODGENET 072
DREAMVISION 235 LOEWE 164
DUKANE 011 025 LOGIK 072
DUMONT 116 073 LUXMAN 363
DURABRAND 096 052 LXI 166 007 138 052 251 333 164
DWIN 257 MAGNAVOX 164 059 116 003 060 061 363 127 022 333 094
DYNASTY 043 226 390 467 431
DYNEX 400 MAJESTIC 333 072
EIKI 187 MARANTZ 116 164 281 562 584
ELECTROBAND 001 MATSUI 164
ELECTROGRAPH 466 MATSUSHITA 080
ELECTROHOME 143 024 076 196 MAXENT 242
ELEKTRA 072
MEGATRON 116 011
ELEMENT 363 494 526 622
MEMOREX 007 072 363
EMERSON 028 048 043 155 005 116 363 047 050 051 076 MGA 116 363 024 028 042
096 143 153 154 052 514 MIDLAND 333 073
ENVISION 116 MINTEK 362
EPSON 324 590 MINUTZ 008
ESA 323 MISAKAI 052
FISHER 007 057 MITSUBISHI 124 109 024 028 040 042 146 363 348 450
FUJITSU 246 198 410 MONIVISION 017
FUNAI 028 043 052 MONTGOMERY WARD 333 072
FUSION 642 MOTOROLA 081
FUTURETECH 043 MTC 116 363 258
GATEWAY 242 268 MULTITECH 043
GE 073 116 008 009 034 056 074 155 333 363 NAD 138 025
GEM 391 NEC 272 197134 116 040 016 024 056 019 262 236
GIBRALTER 116 073 281 575
GO VIDEO 026
NET TV 242
GOLDSTAR 113 116 102 363 106 112 127 143
NEXUS 620 454
GRUNPY 028 043 NIKEI 043
HAIER 363 501 623 NIKKO 116
HALL MARK 363 NIKO 527
HANNSPREE 349 381 NORCENT 390
HARLEY DAVIDSON 028 NORWOOD MICRO 027
HARVARD 043 NTC 103
HAVERMY 081 NUVISION 351 567
HELLO KITTY 076 OLEVIA 432 363 333
HIMITSU 043 ONKING 043
HISENSE 419 442 619 630 631 ONWA 043
HITACHI 011 166 009 010 012 023 075 143 158 072 363 OPTIMUS 025
250 587 613 OPTOMA 265 249
HP 378 316 327 421 OPTONICA 019 251
HUMAX 518
ORION 096
HYPERION 609
PANASONIC 080 034 056 164 208 359 552 524 607
HYUNDAI 337 338 PHILCO 116 003 059 060 164 363 024 056
ILO 472 399 PHILIPS 164 005 093 038 116 003 363 059 127 206 431
INFINITY 164 333 161 594 629
INFOCUS 333 230 547 548 470 532 564 595 PILOT 116
INITIAL 035 282 PIONEER 234 135 025 018 023 116 393 272 520 582
INSIGNIA 350 400 052 164 403 454 457 604 617 POLAROID 388 323 328 353 354 355 356 494 387 391 505
INTEQ 073 506 508
JANEIL 002 PORTLAND 363 143
JBL 164 PRINCETON 004
JCB 001 PRISM 034
JCPENNEY 024 116 008 009 030 065 258 143 333 363
PROSCAN 333
JENSEN 013
PROTON 363 112 058 143 171 172 033 528
JVC 038 034 001 083 199 210 533 581 639 406 PROTRON 392 398 498 499 500
KAWASHO 116 001 PROVIEW 494
KEC 043 PROX 572
KENWOOD 116 001 PULSAR 116 073
KLEGG 466 QUASAR 034 056 606
KLOSS 002 059 RADIO SHACK 019 363 143 043 127
KMC 143
RCA 333 065 116 363 024 056 152 023 074 161 588
KNOLL SYSTEMS 230
REALISTIC 007 019 043 047
KONKA 457
REVOLUTION HD 466
KREISEN 530 RUNCO 182 073 395 416 072 342
KTV 043 116 143 154 SAMPO 116 058 363 242
KURAZAI 072 SAMSUNG 258 050 089 105 363 127 143 333 228 229 515
LG 363 113 116 102 106 112 127 143 569 284 SAMSUX 116