Universal Remote Control CLIKR-5 Operating Instructions

1 4
Operating Instructions For
Introduction Button Functions
The CLIKR TM -5 UR5L-8700L-IP is designed
CLIKR ™ -5 SYSTEM ON/OFF
Designed to send Power On/Off
to operate ADB, Amino, AT&T, Myrio,
commands for up to five Components
with one button press.
Motorola and Wegener IPTV set tops, plus
Refer to section E for details.
the majority of TV, VCR, DVD and AUDIO
MENU
Cable Remote Control
Displays the Applications Menu.
equipment on the market as shown below.
GUIDE
STB : Set top boxes TV : Televisions Displays the program guide listings.
VCR : VCRs and TV/VCRs DVD: DVD Players
UR5L-8700L-IP
OK/SELECT
Selects highlighted screen options.
AUX : Audio Receivers and DVRs, etc.
SETTINGS
2
Displays settings menu.
Replacing Batteries
MUTE
Silences the audio. Press to activate.
Press again to restore sound to the
Before you program or operate the remote
previous level.
control, you must install two new AA alkaline
VOLUME
batteries.
Raises or lowers the sound level.
FAV
STEP1 Remove the battery compartment cover
Displays favorite channels.
on the back of your remote control.
ON DEMAND
Provides direct access to On Demand channel.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the BACK
Return to previous menu screen or TV channel.
illustration below.
STEP3 Replace the battery compartment cover.
M BUTTONS
IPTV company custom-programmable Macros.
Refer to Section K for programming steps.
Replays the previous few seconds of a program.
My DVR
Digital Video Recording.
DELETE
Edit text on the screen.
ON-OFF
Opens or closes the PIP (Picture-In-Picture)
window through the IPTV STB.
VIDEO SOURCE
Selects the video source from available
video Components through the IPTV STB.
SWAP
Swaps the contents of the PIP (Picture-In-Picture) window
and the main viewing screen through the IPTV STB so that
the PIP window displays on the main screen.
3
5
Operations
Programming the Remote Control
DEFAULT STATE: There are two ways you can program your CLIKR
Component Default: Set top box (STB)
* The Pre-Programmed 3-Digit Code Method
Channel Default: STB channel and numbers * The Auto-Search Method
* The Learning Method
through the STB. You have the option of controlling
your STB channel and numbers through the TV or The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit
VCR. Refer to section I for programming steps. code numbers that correspond to a particular Component's manufacturer/brand, so it's the fastest
and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The
Volume Default: Volume and Mute control are
Auto-Search Method scans through all the codes in the remote control, one at a time. The
automatically transferred to the respective
Learning Method allows you to transfer functions from other remotes, one button at a time.
Component mode you select, as follows: STB:
IMPORTANT SETUP NOTE!
Set Top Box / TV: TV / AUX: AUX. Volume and
This pertains to all programming steps. When you are in setup mode, a component LED will light
Mute control for VCR and DVD are automatically
for 30 seconds.If you do not press a button within 30 seconds, the LED light will turn off and exit
transferred to the TV. However, you have the
setup mode and you will need to start over.
Universal Remote Control, Inc. option of controlling STB Volume and Mute
through the TV, VCR or AUX. Refer to section J A. Pre-Programmed 3-Digit Code Method
www.universalremote.com
for programming steps.
OCE-0060G REV 07 (02/26/10)
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX).
STEP2 Press the [COMPONENT] button (TV, Now, repeat the Auto-Search Method for those
VCR, DVD or AUX) to be programmed
Components you could not program earlier
and [OK/SEL] button simultaneously for with the Pre-Programmed Method.If you can't
3 seconds. The Component LED light will
POWER find the right code using the Auto-Search
Allows you to turn your TV, VCR, DVD, AUX turn on for 30 seconds indicating the
Method, try the Learning Method in Section C.
and Set top box On and Off.
unit is ready to be programmed.
AUX, DVD, VCR, TV, STB
C. The Learning Method
Used to select the component you want STEP3 Point the remote control toward the
to operate and signals remote control activity.
Component and enter the 3-digit code
STEP1 Press the [COMPONENT] button
INFO number assigned to your brand.
(TV,VCR,DVD or AUX) to be
Displays information about the program
currently playing or highlighted in the program guide.
*Note : If the 3-digit code number you just programmed and the [ASPECT]
entered is correct, the Component will
EXIT buttons simultaneously for 3 seconds
Exit from current screen.
turn Off. If it did not turn Off, continue
until the Component LED light turns on.
entering code numbers listed for that
PAGE
STEP2 Line up the CLIKR
Accesses pages above or below the brand until the Component turns Off.
information currently displayed.
head-to-head, 1 or 2 inches apart.
CURSOR NAVIGATION PAD STEP4 After you've entered the correct code
STEP3 Press any button on the CLIKR
Navigate to and highlight an item from number and the Component has turned
the on-screen choices.
you want to teach a command to. For
Off, press the [POWER] button to turn the
A, B, C, D example, if you want to teach the
Component back On. Now it is time to
Make direct selections from on-screen menus.
[MUTE] button, press the [MUTE]
test the VOLUME and MUTE buttons for
CHANNEL
button.
the TV (or PLAY and STOP buttons for
Selects the next higher or lower channel.
VCR and DVD) to make sure they all work.
STEP4 Press and hold the [MUTE] button on
LAST
If any of the functions do not work as they
Returns to the previously tuned channel.
the other remote until the CLIKR
should, repeat from STEP 3 using the next
INTERACTIVE Component LED light blinks twice.
3-digit code number listed for that brand
View personalized weather, sports, and traffic.
until you find the best Component code.
*Note : The LED will blink 5 times if there
SKIP
was an error in the learning
STEP5 Once you have found the correct 3-digit
Forward ahead in stored or recorded programs.
code, save it by pressing the same process. In so, repeat STEPS 3 and
VCR/DVD/VOD KEYS
4. Continue learning other buttons
[COMPONENT] button one more time.
Perform standard VCR and DVD functions
when in VCR and DVD mode, and Video-On-Demand The Component LED light will blink by repeating STEPS 3 and 4.
functions when in STB mode.
twice to confirm that the code was
NUMBER PAD STEP5 Once you have completed teaching
successfully stored.
Enter numbers to tune to channels.
CLIKR TM
Also, make numeric entries on on-screen menus.
NOTE: You can also use the CH or the program Now, program the rest of your Components
Component, save the learned commands
guide as alternate ways to tune to channels.
by repeating STEPS 1-5.
by pressing the [COMPONENT] and
ASPECT/ENTER
*Note : If the Pre-Programmed Method did not [ASPECT] buttons simultaneously until
Changes the HD screen viewing aspect
ratio through the IPTV STB.
work, or if the Code Tables do not list the Component LED blinks 3 times. Now
PIP CH +/-
your Component brand, use the Auto- test all the buttons to make sure they
Selects the next higher or lower channel
in the PIP (Picture-In-Picture) window
Search Method as explained in Section B. learned correctly.
through the IPTV STB.
MOVE
Moves the PIP (picture-In-Picture) window to
D. Erasing a Single Learned Command
B. Auto-Search Method
another location on the screen through the
IPTV STB.
LIGHT BUTTON STEP1 Press the [COMPONENT] and [ASPECT]
STEP1 Turn on the Component you want to
Press to backlight all keypad buttons. buttons simultaneously for 3 seconds
program (TV, VCR, DVD or AUX).
Press again to turn off (or simply wait 10 seconds
for automatic shut-off). until the Component LED light turns on.
STEP2 Press the [COMPONENT] button (TV,
VCR, DVD or AUX) to be programmed STEP2 Press and hold the button you want to
erase for 3 seconds. The Component LED
and [OK/SEL] button simultaneously for
3 seconds. The Component LED light will blink twice to confirm the erasure.
TM -5 remote:
will turn on for 30 seconds indicating
STEP3 To exit, press and hold both the
the unit is ready to be programmed.
[COMPONENT] and [ASPECT] buttons
STEP3 Point the remote toward the Component simultaneously until the Component LED
blinks 3 times.
and press the [CH ] or [CH ] button one
step at a time or keep it pressed. The
E. Erasing All Learned Commands
remote will emit a series of ON/OFF
commands. Release the [CH ] or [CH ] from One Component
button as soon as the Component turns Off.
STEP1 Press the [COMPONENT] and [ASPECT]
STEP4 Test functions. (Same as for 3-Digit Code
buttons simultaneously for 3 seconds
Programming Method - Section A). If any
until the Component LED light turns on.
of the functions do not work as they
STEP2 Press and hold both the [COMPONENT]
should, repeat from STEP 3 using [CH ]
button you want to erase and the
or [CH ] buttons to find the correct code.
[PAUSE] button for 5 seconds. The
STEP5 Save the code. (Same as for 3-Digit Code
Component LED will blink twice to
Programming Method - Section A).
confirm the erasure.
STEP3 To exit, press and hold both the [COMPONENT] H. Programming the System On/Off Button
and [ASPECT] buttons simultaneously until the
This allows you to program the System On/Off
Component LED blinks 3 times.
button so it can send up to five power On/Off
F. Finding a Component Button's
commands with one button press.
Setup Code Number
STEP1 Press the [STB] button.
If you used either the Auto-Search or Learning
STEP2 Press the [SYSTEM ON/OFF] button
Methods to program a Component, you may not
and the [OK/SEL] button simultaneously
know what the correct code number is. Here is
for 3 seconds. The [STB] button will
a way for you to identify the code number, so
turn on for 30 seconds.
you can record it for future reference.
STEP3 Press the first [COMPONENT] button you
STEP1 Press the [COMPONENT] button (TV,
want to store in the [SYSTEM ON/OFF]
VCR, DVD or AUX) you want to verify
button and then the [POWER] button. Repeat
TM -5 to the other remote, and the [OK/SEL] button simultaneously
this for other Components until you have
for 3 seconds. The Component LED light
stored all the desired power commands into
will turn on for 30 seconds. the [SYSTEM ON/OFF] button.
TM -5 that
STEP2 Press the [INFO] button and count the STEP4 Press the [CH ] button to save the
number of times the Component LED light power commands you stored. The
blinks. This number indicates the first [STB] button will blink twice to confirm
the commands have been saved.
digit of the code, followed by the second
and third, each separated by a one
I. Programming Channel Control
second pause when the LED will turn off.
TM -5
You can program the channel controls (Channel
*Note : 10 blinks represents the number zero.
Up, Channel Down, Last and Numbers) from
Example : One blink, (pause), eight blinks,
one Component to operate in another
(pause) and three blinks, indicates
Component mode. Default channel control
code number 183. settings on the remote control are as follows:
G. AUX Function: Programming a 5 th STB : STB T V : STB
DVD: DVD AUX: AUX
Component
If you wish to store the TV channel control in
You can take advantage of the AUX function to
program a 5 th Component such as a second TV mode, use the following steps.
-5 all desired commands for that
TV, VCR, DVD or Audio Component.
STEP1 Press the [TV] button and the [OK/SEL]
button simultaneously for 3 seconds.
STEP1 Turn on the 5 th Component you want
The [TV] Component LED will turn on
to program (TV, VCR, DVD or Audio).
for 30 seconds.
STEP2 Press the [AUX] button and the
Press the [VOL ] button.
STEP2
[OK/SEL] button simultaneously for 3
seconds.The [AUX] Component LED STEP3 Press the [TV] button again.
will turn on for 30 seconds.
The Component LED will blink twice
to confirm the programming.
STEP3 Press the [COMPONENT] button you
want to setup. Point the remote
To return to original state:
control toward the Component and
If you wish to restore the STB channel control
enter the 3-digit code number
in TV mode, repeat the above steps but press
assigned to your brand.
[STB] in STEP3 .
*Note : If the 3-digit code number you just
entered is the correct number, the J. Programming Volume Control
Component will turn Off. If it did not
Volume and Mute control are factory-programmed
turn Off, continue entering code
to automatically transfer to the respective
numbers listed for that brand until
Component mode you select, as follows:
the Component turns Off.
STB : STB T V : TV
STEP4 Test functions. (Same as for 3-Digit Code
DVD: TV AUX: AUX
Programming Method - Section A). If any
of the functions do not work as they However, you can program the volume controls
(Volume Up, Volume Down and Mute) from one
should, you need to find a new code.
Component to operate in another Component.
STEP5 Once you have found the correct 3-digit
If you wish to store the TV volume control in
code, save it by pressing the [AUX]
STB mode, use the following steps.
button one more time. The Component
LED light will blink twice to confirm the
STEP1 Press the [STB] button and the
code was stored. Now when you
[OK/SEL] button simultaneously for 3
press the AUX button, all the buttons
seconds. The [STB] Component LED
will work with that 5 th Component. will turn on for 30 seconds.
6
STEP2 Press the [VOL ] button.
Set-up Code Tables
STEP3 Press the [TV] button.
STB-IPTV
The Component LED will blink twice to
confirm the programming.
Manufacturer/Brand Set-Up Code Number
To return to original state:
ADB 254 255 315 259
AMINO 249 256 257 260 261
If you wish to restore the STB volume control in
AT&T 251
STB mode, repeat the above steps but press
CISCO 313 251 316
[STB] in STEP3 . COMCAST 313
ENTONE 155 258
K. Programming a 'Macro' button.
MYRIO 254 255
MOTOROLA 253
If your remote model has custom-programmable
NOW TV 314
Macro buttons available, they can be programmed to
PACE 313
act as a 'Macro' or Favorite Channel button in STB
SCIENTIFIC ATLANTA 251
mode. This allows you to program up to five 2-digit
WEGENER 250
channels, four 3-digit channels or three 4-digit
STB-CABLE Converters
channels that can be accessed with one button press.
Manufacturer/Brand Set-Up Code Number
STEP1 Press the [STB] button to select the STB mode.
SCIENTIFIC ATLANTA 001 003 041 042 045 046
STEP2 Press the [MACRO] button and [OK/SEL]
PIONEER 001 103 034 051 063 076 105
button simultaneously for 3 seconds. The
PACE 001 005 002
[STB] button will turn on for 30 seconds.
SAMSUNG 001 030
MOTOROLA 002 111 148
Enter the the 2, 3 or 4-digit code for the
STEP3
DIGEO 153
channel you want programmed first (for
GENERAL INSTRUMENT 005 103 104
example, 007) using the Number Pad, then HAMLIN 049 050 055
HITACHI 103 055
press the [STOP] button. Then enter the code
JERROLD 005 004 103 005 003 008 009 010 069
for the next channel (for example, 050), then
MAGNAVOX 010 012
VCR: STB press the [STOP] button. Repeat this process
MEMOREX 052
for the third channel. The [STB] button will
MOXI 111 252 153
blink once for each channel entered.
NFUSION 192
PANASONIC 044 047
STEP4 Press the [CH ] button to store the
PHILIPS 006 012 013 020 085
channels that were selected. The [STB]
PULSAR 052
button will blink twice to confirm the RCA 047
storage of commands. REGAL 049 050
REGENCY 057
To access the programmed channels, press the SKY 230 204
SONY 108
[MACRO] button once. This will bring up the first
SPRUCER 047
channel. Press once again and it will bring up
TELNET 354
the second channel. Press again and it will
TOCOM 039 040 056
bring up the third channel.
TOSHIBA 052
VIEWSTAR 012 015
L. Low Battery Warning
ZENITH 052 060 093 100
When the batteries are low and need to be
TV
replaced with fresh batteries, the Component LED
Manufacturer/Brand Set-Up Code Number
lights will blink 2 times in sequence whenever a
[POWER] button is pressed to turn on equipment. A MARK 112 143
ABEX 025
ACCURIAN 036
M. Memory Lock System
ADMIRAL 072 251 333
ADVENT 247 388
This remote control is designed to retain
ADVENTURA 002
programmed memory for 10 years even after
AIKO 103
VCR: TV
batteries are removed from the remote control.
AKAI 116 146 248 404 405 473 475 323 387 391
ALBATRON 017
N. Record Your Component Set-up Codes
ALERON 028
AMERICA ACTION 043
TV Set-up Code Number:
AMPRO 073
AMSTRAD 052
VCR Set-up Code Number:
ANAM 043 054 056 080 112
AOC 116 363 112 058
DVD Set-up Code Number:
APEX 572
AUX Set-up Code Number: APEX DIGITAL 006
AQUAVISION 573 574
For additional information about your remote
ASTAR 477
control, go to www.universalremote.com
AUDIOVOX 076 454 388
TV TV
Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number
AVENTURA 052 HARLEY DAVIDSON 028
AVION 441 HARVARD 043
AXION 039 HAVERMY 081
BELCOR 116 HELLO KITTY 076
BELL&HOWELL 333 072 HIMITSU 043
BENQ 423 600 HISENSE 419 442
BOXLIGHT 266
HITACHI 011 166 009 010 012 023 075 143 158 072
BRADFORD 043
363 250 587
BROCKWOOD 116
HP 378 316 327 421
BROKSONIC 238
HUMAX 518
BYDESIGN 031 032 HYUNDAI 337 338
CANDLE 116 002 003 363 ILO 472 399
CAPEHART 058 INFINITY 164
CARY AUDIO DESIGN 266
INFOCUS 333 230 547 548 470 532 564 595
CELEBRITY 001
INITIAL 035 282
CENTURION 116
INSIGNIA 350 400 052 164 403 454 457
CETRONIC 043
INTEQ 073
CHANGHONG 247
JANEIL 002
CITIZEN 116 002 003 363 043 258 103 143
JBL 164
CLARION 043
JCB 001
CLASSIC 043
JCPENNEY 024 116 008 009 030 065 258 143 333 363
CLP CLASSIC 333
JENSEN 013
COLORTYME 116
JVC 038 034 001 083 199 210 533 581
CONCERTO 363
KAWASHO 116 001
CONCIERGE 073
KEC 043
CONTEC 043 050 051
KENWOOD 116 001
CORNEA 116
KLEGG 466
CORONADO 143
KLOSS 002 059
CRAIG 043 054
KMC 143
CROSLEY 164
KNOLL SYSTEMS 230
CROWN 043 143
KONKA 457
CURTIS MATHES 116 258 363 143
KREISEN 530
CXC 043
KTV 043 116 143 154
CYBERHOME 015
KURAZAI 072
DAEWOO 363 016 043 044 076 103 114 125 127 143
LG 363 113 116 102 106 112 127 143 569 284
DAYTRON 363 143
LITEON 268
DELL 320 164 363
LODGENET 072
DIGITAL PROJECTION 570
LOEWE 164
DIMENSIA 333
LOGIK 072
DREAMVISION 235
LUXMAN 363
DUKANE 011 025
LXI 166 007 138 052 251 333 164
DUMONT 116 073
MAGNAVOX 164 059 116 003 060 061 363 127 022 333
DURABRAND 096 052
094 226 390 467 431
DWIN 257
MAJESTIC 333 072
DYNASTY 043
MARANTZ 116 164 281 562 584
DYNEX 400
MATSUI 164
EIKI 187
MATSUSHITA 080
ELECTROBAND 001
MAXENT 242
ELECTROGRAPH 466
MEGATRON 116 011
ELECTROHOME 143 024 076 196
MEMOREX 007 072 363
ELEKTRA 072
MGA 116 363 024 028 042
ELEMENT 363 494 526
MIDLAND 333 073
EMERSON 028 048 043 155 005 116 363 047 050 051
MINTEK 362
076 096 143 153 154 052 514
MINUTZ 008
ENVISION 116
MISAKAI 052
EPSON 324 590
MITSUBISHI 124 109 024 028 040 042 146 363 348 450
ESA 323
FISHER 007 057 MONIVISION 017
FUJITSU 246 198 410 MONTGOMERY WARD 333 072
FUNAI 028 043 052 MOTOROLA 081
FUTURETECH 043 MTC 116 363 258
GATEWAY 242 268 MULTITECH 043
NAD 138 025
GE 073 116 008 009 034 056 074 155 333 363
NEC 272 197134 116 040 016 024 056 019 262
GEM 391
GIBRALTER 116 073 236 281 575
GO VIDEO 026 NET TV 242
GOLDSTAR 113 116 102 363 106 112 127 143 NIKEI 043
GRUNPY 028 043 NIKKO 116
HAIER 363 501 NIKO 527
HALL MARK 363 NORCENT 390
HANNSPREE 349 381 NORWOOD MICRO 027