Network Connection; Connection Test; Enable(Easy); Enable(Custom) - Toshiba BDX2000KB Owner's Manual

E5RJ0BD_EN.book Page 36 Tuesday, October 20, 2009 3:53 PM

Network Connection

Set up the network connection settings in order to use the
BD-Live function with a BD-Live disc.

Connection Test

[Setup] A "Custom" A "Others" A
After you made IP address/DNS settings or when a LAN
cable is connected, always perform the connection test to
check if the connection is correctly made.
1
In stop mode, press [SETUP].
2
Use [K / L] to select
3
Use [K / L] to select "Others", then press
[ENTER].
4
Use [K / L] to select "Network Connection",
then press [ENTER].
5
Use [K / L] to select "Connection Test", then
press [ENTER].
Connection test will start automatically and the test result
will appear right after the connection test finishes.
• "Testing... " : The test is in progress.
• "Pass" : Connection test is successfully
completed.
• "Fail" : Connection test failed.
Check the connection settings.
Press [ENTER] to go to the list of network status
confirmation screen.
Others
Connection Test
IP Address
Subnet Mask
Default Gateway
Primary DNS
Secondary DNS
then press 'ENTER'.
6
Press [ENTER] to go back to the previous
screen, or press [SETUP] to exit.
Note
• If the connection test passes, you can enjoy the
BD-Live functions using the Internet without making
any extra settings.
• If the connection test fails, you may need to change
the MAC address settings of your router. You can
check the MAC address of this unit on
"Enable(Custom)" screen.
• "Connection Test" is not available when "Disable" is
selected in "Network Connection".
36
FUNCTION SETUP
"Network "Connection
A
Connection" Test"
, then press [ENTER].
xxx.xxx.xxx.xxx
xxx.xxx.xxx.xxx
xxx.xxx.xxx.xxx
xxx.xxx.xxx.xxx
xxx.xxx.xxx.xxx

Enable(Easy)

[Setup] A "Custom" A "Others" A
Network settings are set to the following settings initially.
(In most cases, you can connect to the Internet without
making any changes to the default settings.)
- IP Address Setting Auto(DHCP)
- DNS Setting Auto(DHCP)
- Proxy Setting Do Not Use
- Connection Speed Auto
- BD-Live Setting Allow
If you want to set the network settings back to the default
settings as above (except "BD-Live Setting"), follow the
procedure below.
1
Follow steps 1 to 4 in "Connection Test" on
page 36.
2
Use [K / L] to select "Enable(Easy)", then press
[ENTER].
• The unit will start the connection test automatically
and the test result will appear right after the test
finishes.
• After the connection test finishes, press [ENTER] to go
to network status confirmation screen.
3
Press [ENTER] to activate the network settings
and set the network connection automatically.
Press [SETUP] to exit.
Note
• The setting of "BD-Live Setting" will not be set back
to the default, even if you follow the procedure.

Enable(Custom)

[Setup] A "Custom" A "Others" A
In following cases, select "Enable(Custom)" to set each
setting as necessary.
- When connection test failed with the setting of
"Enable(Easy)".
- When instructed by your Internet service provider to
make specific settings in accordance with your
network environment.
IP Address Setting / DNS Setting
1
Follow steps 1 to 4 in "Connection Test" on
page 36.
2
Use [K / L] to select "Enable(Custom)", then
press [ENTER].
3
Use [K / L] to select "IP Address Setting", then
press [ENTER] repeatedly to select the desired
setting.
"Auto(DHCP)" : If your router has DHCP server
function, select "Auto(DHCP)".
"Manual" : If your router does not have DHCP
server function, select "Manual".
"Network "Enable
A
Connection" (Easy)"
"Network "Enable
A
Connection" (Custom)"
EN