Sign in today to find solutions:

Forgot your password?

Don't have an account? Sign up

 
Next >>
<< Previous
Getting Your Multifunction
Back On Your Network
After A Router Or Network Change
PIXMA MG5320
Macintosh OS
1

Summary of Contents

  • Page 1

    Next >> << Previous Getting Your Multifunction Back On Your Network After A Router Or Network Change PIXMA MG5320 Macintosh OS...

  • Page 2

    Information << Previous Next >> Important If any of the following situations exist • You have replaced your Router or Access Point • You want to use a different wireless network • Router settings have been changed. Please complete the following steps to apply the new configuration settings to your multifunction.

  • Page 3

    Preparing to Connect My Multifunction << Previous Next >> To My Network Network Requirements Before connecting the machine to the network, make sure that configuration of the computer and access point or router is complete, and that the computer is connected to the network. Wireless Connection Before connecting the machine to the network, the computer needs to be connected to the network.

  • Page 4

    Preparing to Connect My Multifunction << Previous Next >> To My Network An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without using an access point, is not supported. A wireless access point or router is required to use your printer on a wireless LAN.

  • Page 5

    Setup CD-ROM during restarting. The installation resumes once your computer has restarted. • If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting to access the network. If such a warning message appears, set the security software to always allow access.

  • Page 6

    << Previous Next >> Installing the PIXMA MG5320 on Your Wireless Network When you reinstall your printer on your network because of a router or network change, you follow the same procedure as for a first time install. A step-by-step walk through of the wireless setup is built in to the installation routine of the software that shipped with your PIXMA.

  • Page 7

    << Previous Next >> Installing the PIXMA MG5320 on Your Wireless Network Continue to follow on-screen instructions. Be sure to select Wireless Connection on the Connection Method Selection screen (1-2). Continue to follow instructions until the Setup Procedure Selection screen (3-1)appears. This is shown on the next page...

  • Page 8

    Connecting to the Wireless Network << Previous Next >> The printer automatically searches for access points that support WPS (Wi-Fi Protected Setup)*. *Unless you are absolutely sure your access point supports WPS and you are familiar with activating this on your access point, press the Stop button on the printer’s operation panel and click on Other Methods on the Setup Procedure Selection screen (screenshot shown below)*.

  • Page 9

    Connecting to the Wireless Network << Previous Next >> For Standard setup only Select Standard setup on the Setup Procedure Selection screen (3-2) Continue to next page before proceeding any further with setup...

  • Page 10

    Connecting to the Wireless Network << Previous Next >> Follow On-screen instructions. When you get to Step 4-2 and later in Step 4-4 ( screens shown below) you will need to know SSID and password information* Step 4-4 Step 4-2 *Unless you are absolutely certain of this information, please continue to the next page for information on locating / verifying this information Continue to follow the on-screen instructions.

  • Page 11

    Connecting to the Wireless Network << Previous Next >> If you don't know your Access Point / Router name or SSID*, or the Passphrase or Network key for your wireless network, you can find this information during Standard setup using the Setup CD-ROM or the downloaded file (Mini Master Setup). *The terms 'SSID' and 'AccessPoint / Router' refer to a name used to identify the specific Access Point or Router.

  • Page 12

    Network setup is complete. Continue to follow any remaining On-screen instructions to install the software. On the Software Installation List screen, select any software to be installed. MP Drivers and Canon IJ Network Tool are required for the printer to be able to print and scan and cannot be de-selected.

  • Page 13

    Installing the Drivers & Software << Previous Next >> Click Add Printer on the Add Printer window.

  • Page 14

    Installing the Drivers & Software << Previous Next >> Select the Canon MG5300 series with Canon IJ Network listed in the Kind column. Click Add.

  • Page 15

    Installing the Drivers & Software << Previous Next >> Click Next on the Add Printer window. Setup is complete. Continue to follow on-screen instructions to finish and exit the setup program.

  • Page 16

    Installing the Drivers & Software << Previous Installing the PIXMA MG5320 on Your Wireless Network If you can’t find your CD-ROM, you may download the MG5300 series Mini Master Setup, which includes the same step-by-step installation as the CD-ROM, by following the instructions below: Click here to access the MG5320 Drivers &...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: