Canon PIXMA MG6320 Setup Manual
Hide thumbs
Also See for PIXMA MG6320:
- Online manual (270 pages) ,
- Network setup manual (17 pages) ,
- Getting started manual (4 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Canon PIXMA MG6320
Summary of Contents for Canon PIXMA MG6320
-
Page 1: Setup Guide
PIXMA MG6300 series Setup Guide © CANON INC. 2012... - Page 2 Setup Guide This guide provides information for setting up a network connection for the printer. Network Connection Wireless Connection Preparation for Connection Printer Setup Setup Procedure Selection Push Button Method Standard setup Other setup (Advanced setup) Disable WPA/WPA2 Wired Connection Preparation for Connection Cable Connection Printer Setup...
-
Page 3: Wireless Connection
Network Connection Wireless Connection a Preparation for Connection Before Starting Wireless Connection Setup 1. Make sure that the printer is turned on. If the power is on, the POWER lamp (A) will be lit. Notes on Wireless Connection • Make sure that the computer is connected to the access point (A) (or wireless network router) you want to connect your printer to. -
Page 4: Setup Procedure Selection
2. Flick the screen left or right, then tap the WLAN setup icon. The (blue) Wi-Fi lamp (A) lights up when wireless connection is enabled. c Setup Procedure Selection The printer will automatically search for access points supporting WPS (Wi-Fi Protected Setup). * If the Push Button Method screen is displayed on the printer When you are unsure if your access point or router supports this technology, tap To other connection methods. -
Page 5: Connection Using Wps
Push Button Method d Connection Using WPS 1. Press and hold the WPS button on the access point. For details on pressing the WPS button, refer to the access point manual. 2. Tap Start setup on the printer within 2 minutes. The (blue) Wi-Fi lamp on the printer fl... -
Page 6: Connection Via Standard Setup
Standard setup d Connection via Standard setup 1. Tap Standard setup. 2. Tap your access point. 3. One of the screens below will be displayed on the printer. 4. Tap the screen. 5. Enter the network password (WEP key or passphrase). Character entry is case-sensitive. - Page 7 d Connection Using WPS 1. Tap WPS. 2. Tap Push button method. 3. Tap OK. 4. Press and hold the WPS button on the access point. For details on pressing the WPS button, refer to the access point manual. 5. Tap OK on the printer within 2 minutes. The (blue) Wi-Fi lamp on the printer fl...
- Page 8 Other setup (Advanced setup) d Connection via Advanced setup 1. Tap Other setup. 2. Tap Advanced setup. 3. Tap your access point. 4. Tap the security protocol used by the access point. Disable 5. When the left screen appears, tap OK. The network connection setup is now complete.
- Page 9 5. Tap the WEP key number you want to use. 6. Tap the screen. 7. Enter the WEP key. Character entry is case-sensitive. 8. Tap Apply. 9. Make sure that the WEP key is correct. 10. Tap OK. 11. When the left screen appears, tap OK. The network connection setup is now complete.
- Page 10 WPA/WPA2 5. Tap the screen. 6. Enter the passphrase. Character entry is case-sensitive. 7. Tap Apply. 8. Make sure that the passphrase is correct. 9. Tap OK. 10. When the left screen appears, tap OK. The network connection setup is now complete.
-
Page 11: Wired Connection
Wired Connection a Preparation for Connection Before Starting Wired Connection Setup 1. Make sure that the printer is turned on. If the power is on, the POWER lamp (A) will be lit. Notes on Wired Connection Make sure that the computer and router (A) (or access point) are connected. •... -
Page 12: Printer Setup
c Printer Setup 1. If the HOME button (A) on the printer is lit, touch the HOME button. 2. Flick the screen left or right, then tap Setup. 3. Flick the screen up or down, then tap Device settings. 4. Tap LAN settings. 5. -
Page 13: Character Entry
Character Entry You can enter the characters when the keyboard is displayed on the printer. Follow the procedure below. 1. You can enter the characters when the keyboard is displayed on the printer's LCD. Password entry is case sensitive. : Tap to switch between "lower case letters" and "numbers and symbols." : While letters of the alphabet appear, tap to switch between upper and lower case letters. -
Page 14: Troubleshooting
Troubleshooting Standard setup The Target Access Point is Not Detected • Is the network device (router, etc.) turned on? If the network device is already turned on, turn it off, then turn it back • Check the access point name/network name and network password of your access point or router. •... - Page 15 When using multiple access points: Tap Use multiple AccessPoints. An Unknown Access Point is Displayed Access points in use nearby may also be detected. The Access Point Name is Not Displayed Properly Access point names with double-byte characters are not displayed properly. However, they can be selected. The Access Point Name is Not Displayed Automatically ...
- Page 16 Failed to connect to the access point. Make sure that the WEP key entered for the access point is correct. In addition, when using WEP key number 2, 3 or 4 of the access point, set to use WEP key number 1, or select a WEP key number by entering wireless connection settings of the printer directly.
- Page 17 WPA/WPA2 Failed to connect to the access point. Make sure that the passphrase entered for the access point is correct. If the problem is not resolved, there may be other causes. See also the sections below: • If the DHCP function of the access point is inactive, enable the DHCP function and confi gure wireless connection settings again.
- Page 18 To perform Standard setup again 1. Touch the HOME button (A). 2. Flick the screen left or right, then tap the WLAN setup icon.
- Page 19 Cannot connect. Connections are being attempted from multiple access points simultaneously. The screen appears when connections are being attempted from multiple access points simultaneously. Wait for a while, then confi gure WPS settings again. Press the WPS button on only one access point. Failed to connect.
-
Page 20: Advanced Setup
Advanced setup The Target Access Point is Not Detected • Is the network device (router, etc.) turned on? If the network device is already turned on, turn it off, then turn it back • Check the access point name/network name and network password of your access point or router. •... - Page 21 When using multiple access points: Tap Use multiple AccessPoints. An Unknown Access Point is Displayed Access points in use nearby may also be detected. The Access Point Name is Not Displayed Properly Access point names with double-byte characters are not displayed properly. However, they can be selected. The Access Point Name is Not Displayed Automatically ...
-
Page 22: Wep
Failed to connect to the access point. Make sure that the WEP key entered for the access point is correct. In addition, when using WEP key number 2, 3 or 4 of the access point, set to use WEP key number 1, or select a WEP key number by entering wireless connection settings of the printer directly. -
Page 23: Perform Advanced Setup Again
The device may not be able to connect to the network in the following cases: If the DHCP function of the access point is inactive, enable the DHCP function or specify the IP address (IPv4 only) of the printer and confi gure wireless connection settings again. In addition, make sure that the selected WEP key number and entered WEP key are correct. - Page 24 WPA/WPA2 Failed to connect to the access point. Make sure that the passphrase entered for the access point is correct. If the problem is not resolved, there may be other causes. See also the sections below: • If the DHCP function of the access point is inactive, enable the DHCP function and confi gure wireless connection settings again.
- Page 25 To perform Advanced setup again 1. Touch the HOME button (A). 2. Flick the screen left or right, then tap the WLAN setup icon.