Advertisement
Quick Links
ET-508 /ET-508S
TP-Fiber (Multi-mode / Single-mode)
IEEE802.3 Ethernet Converter
1. Overview
IEEE802.3 10Mbps Ethernet supports various type media for network connection such as
10Base-2, 10Base-T and 10Base-FL. The media converter is used to convert one type
media signal to other type equivalent that allows multiple type segments connect easily and
inexpensively. This converter can be used as a standalone unit or as a slide-in module to the
19" Media Chassis (up to 10 units) for use at a central wiring closet.
2. Model Description
Model
Descripton
ET-508S TP-FL (Fdx/Hdx supported) RJ-45
TP-FL (Hdx)
ET-508
ET-509A TP-BNC
The available Fiber –optic mode
ST, MM
ST type connector, Multi-Mode
ST, SM
ST type connector, Single-Mode
3. Checklist
Before you start installing the Converter, verify that the package contains the following:
The Converter
AC-DC Power Adapter
This User's Manual
T-Connector(for ET-509A only)
Please notify your sales representative immediately if any of the aforementioned items is
missing or damaged.
ET-509A
TP-BNC Converter
Connector Type
10Base-FL ST (SM)
RJ-45
10Base-FL ST (MM)
RJ-45
10Base-2 BNC
1
Advertisement
Related Manuals for Planet ET-508
Summary of Contents for Planet ET-508
-
Page 1: Model Description
ET-509A TP-BNC Converter ET-508 /ET-508S TP-Fiber (Multi-mode / Single-mode) IEEE802.3 Ethernet Converter 1. Overview IEEE802.3 10Mbps Ethernet supports various type media for network connection such as 10Base-2, 10Base-T and 10Base-FL. The media converter is used to convert one type media signal to other type equivalent that allows multiple type segments connect easily and inexpensively. -
Page 2: Panel Layout
4. Panel Layout 10Mbps ET-508/ ET-508S Front and Side Panel 10Mbps ET-509A Front and Side Panel Power Input +5VDC Jack on Rear Panel... -
Page 3: Installing The Converter
5. Installing the Converter For as a standalone unit: Verify adapter conforms your country AC power requirement and insert the power plug Connect the media cable for network connection For as a slide-in unit: The slide-in Media Converter and Converter Rack should be supplied only from the same source, both Media Converter and Rack are built to match each other at dimensions, DC jack, DC receptacle and power safety Turn off the 19"... -
Page 4: Led Description
10Mbps Hdx ET-508S support Full-duplex mode operation that can double the bandwidth, please make sure the TP ends device also support full-duplex and set to it as well. ET-508/ ET-509A support Hlaf-duplex mode only. 7. LED Description ET-508/ ET-508S TP-Fiber Converter... - Page 5 Warning: To prevent from component damage, please check the cable and the your duplex mode fiber device in the other ends before power on 10Base-FL ST/SC Fiber Cable Limitations: Fiber Half/Full-duplex Multi-mode: Fiber Full-duplex Single-mode: 10Km Data Transfer Rate: 10Mbps at half-duplex (20Mbps for full-duplex mode only) LED Indicators : FL Link/Act, Power, TP Link/Act, Col...
- Page 6 9. TP-BNC Technical Specifications Standards : IEEE802.3 10Base-T/10Base-2 TP Port : RJ-45 jack with a slide switch for "DTE" or "MPR" selection BNC Port : BNC connector Cable and Distance : Category 3/5 unshielded or shielded twisted pair (UTP/STP) wire, maximum length 100 meters (328ft) 0.2 inch diameter RG-58A/U, 50 (ohm) coaxial cable, maximum length 185 meters(607ft)