Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Packard Bell EasyNote E Series
Summary of Contents for Packard Bell EasyNote E Series
- Page 1 EasyNote E series Disassembly Manual...
-
Page 2: Table Of Contents
Removing the Optical Disk Drive..........................13 Removing the Keyboard ............................14 Removing the Main Board............................15 Removing the LCD Module ..........................20 Removing the LCD Panel.............................21 Removing the Touch Pad.............................24 Removing the Speaker Assembly ........................25 DIP Switch Setting..............................25 Screws..................................26 Notice ...................................27 EasyNote E Series Disassembly Manual Page 2... -
Page 3: Overview
Furthermore, the screws that are removed are shown next to the image of the parts themselves. NEC reserves the right to make changes to the EasyNote E series chassis without notice. Technician Notes Only technicians authorized by NEC Computers International BV should attempt to repair this equipment. -
Page 4: Hazardous Voltage
Inside the power supply are hazardous avviare il sistema senza aver prima messo a voltages that can cause serious personal injury. Always posto il coperchio return a defective power supply to your dealer. EasyNote E Series Disassembly Manual Page 4... -
Page 5: Removing The Battery
Removing the Battery Perform the following steps to remove the battery: 1. Make sure to power off the EasyNote E series. 2. Turn the unit upside down. 3. Unlock the battery and slide it out of its place as the arrow shows in Fig. 1 Fig. -
Page 6: Removing The Hard Disk Drive
1. Remove the screws as shown in Fig. 2 M3.5x2 Black Fig. 2 Removing the Hard disk drive cover 2. Release screw that secure HDD module as shown in Fig. 3 M6x2.5 Black Fig. 3 Screw on HDD module EasyNote E Series Disassembly Manual Page 6... - Page 7 Fig. 4 Disconnecting the hard disk drive 4. Unscrew the four screws on both sides of the hard disk drive as shown in Fig. 5 M4x3 Silver Fig. 5 Unscrewing the hard disk drive bracket screws EasyNote E Series Disassembly Manual Page 7...
-
Page 8: Removing The Memory Module
Fig. 6 Removing the screw retaining the memory module slot cover 2. Unclip memory module as shown in Fig. 7 Fig. 7 Removing the memory module 3. Remove the memory module from its slot and put it aside. EasyNote E Series Disassembly Manual Page 8... -
Page 9: Removing The Wireless Lan
Fig. 8 Removing the screws screw retaining the mini PCI slot cover 2. Disconnect the wireless antenna wires from the wireless module Unclip and remove the wireless LAN module. Fig. 9 Wireless LAN & MCD Modem Module EasyNote E Series Disassembly Manual Page 9... -
Page 10: Removing The Cpu
4. Remove heat sink screws, disconnect fan connector and lift up the heat sink. M10.5x2 Sliver Fig. 11 Removing the screws retaining the heat plate. Exact location of CPU socket can differ from this image. EasyNote E Series Disassembly Manual Page 10... - Page 11 5. Unlock CPU from CPU socket and lift up the CPU carefully. Fig. 12 Unlock CPU for EasyNote E2,E4 and E5. Fig. 13 Unlock CPU for EasyNote E6. EasyNote E Series Disassembly Manual Page 11...
- Page 12 Fig. 14 Unlock CPU for EasyNote E1 and E3. EasyNote E Series Disassembly Manual Page 12...
-
Page 13: Removing The Optical Disk Drive
Note 2: When assemble the ODD, you might put a tine cardboard on the ODD before insert it to base unit. It will easy the ODD installation Note 3: You consider removing Bottom Cover before remove ODD. EasyNote E Series Disassembly Manual Page 13... -
Page 14: Removing The Keyboard
1. Push the keyboard cover from battery compartment as shown in Fig. 16 Fig. 16 Releasing the keyboard cover 2. Lift up the keyboard cover carefully as shown in Fig. 17 Fig. 17 Lifting up Keyboard Cover EasyNote E Series Disassembly Manual Page 14... -
Page 15: Removing The Main Board
Keyboard) then perform the following steps: 1. Use small flat screwdriver to remove hinge cover and release screws near to battery compartment at both side. M4.5x3.5 Black Fig. 19 Removing the top cover screws EasyNote E Series Disassembly Manual Page 15... - Page 16 2. Disconnect all cable connection located near to left speaker as shown in Fig. 20 Fig. 20 LCD Cable and Left speaker connection 3. Disconnect Touch Pad Connection as shown in Fig. 21 Fig. 21 Touch Pad connection EasyNote E Series Disassembly Manual Page 16...
- Page 17 5. Carefully lift up, release the top cover, and put it aside. 6. Unscrew screws on MDC Modem module and disconnect it before lift up MDC Modem. M4.5x3.5 Black Fig. 23 Removing the top cover EasyNote E Series Disassembly Manual Page 17...
- Page 18 A = M5x2.5 Sliver B = M6x2 Black C = M2.5x10 silver Fig. 24 Screws on Main Board 8. Lift up Main Board as shown in Fig. 25 Fig. 25 Lifting up Main Board EasyNote E Series Disassembly Manual Page 18...
- Page 19 Note 1: When lifting up Main Board bewares the coil, attach on the Wireless Antenna. Note 2: Make sure Wireless Antenna are properly place in correct location when assemble. EasyNote E Series Disassembly Manual Page 19...
-
Page 20: Removing The Lcd Module
To remove LCD Module first remove Main Board (see Removing Main Board), then perform the following steps: 1. Release screws show in Fig. 26 M6x2.5 Black Fig. 26 Removing screws retaining LCD Module 2. Carefully lift up the LCD Module. EasyNote E Series Disassembly Manual Page 20... -
Page 21: Removing The Lcd Panel
Fig. 27 Removing the rubber covers & screws on the LCD Module 2. Release the LCD Bezel carefully and put it aside as shown in Fig. 28 Fig. 28 Removing the LCD Bezel EasyNote E Series Disassembly Manual Page 21... - Page 22 Fig. 29 Removing the LCD panel screws 4. Remove the screws at both sides of the LCD panel in order to release the LCD hinges as shown in Fig. 30 M3.5x2 Black Fig. 30 Removing the LCD Panel hinges EasyNote E Series Disassembly Manual Page 22...
- Page 23 6. Remove the screws on LCD module holder at both sides of the LCD base cover and put it aside. Fig. 32 Removing Wireless Antenna M6x2.5 Black 7. Remove the screws at both sides of the LCD Hock and put it aside. M3.5x2 Sliver Fig. 33 LCD Hock EasyNote E Series Disassembly Manual Page 23...
-
Page 24: Removing The Touch Pad
1. Unscrew the screws on the Top Cover as shown in Fig. 34 A = M3.5x2 Black B = M3x2 Sliver C = M3.5x2.5 Sliver Fig. 34 Top cover 2. Carefully separate Touch Pad module from Top cover. EasyNote E Series Disassembly Manual Page 24... -
Page 25: Removing The Speaker Assembly
1. Remove the screws holding Speaker Assembly as shown in Fig. 35 M4.5x2 Black Fig. 35 Speaker Assembly 2. Carefully remove the Speaker assembly from Top Cover and place it aside. DIP Switch Setting No DIP switch setting required on EasyNote E series. EasyNote E Series Disassembly Manual Page 25... -
Page 26: Screws
Screws M3.5x2 Black M6x2.5 Black M4x3 Silver M10.5x2 Sliver M4.5x3.5 Black M3x2 Sliver M5x2.5 Sliver M6x2 Black M2.5x10 silver M4.5x2.5 Sliver M3.5x2.5 Sliver M4.5x2 Black M3.5x2 Sliver EasyNote E Series Disassembly Manual Page 26... -
Page 27: Notice
Copyright © 2005 NEC Computers International BV. All rights reserved. NEC is a trademark of NEC Computers International BV. The names of actual companies and products mentioned herein may be trademarks and/or registered trademarks of their respective owners. EasyNote E Series Disassembly Manual Page 27...