ANUAL Tiller/Cultivator Operator's Manual MODEL TC-210 Serial Number 05001001 - 05999999 WARNING DANGER Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual, which must be read and understood for proper and safe operation. X7504082500 X750004170 10/02...
NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job-dependability. Read and understand this manual. You will find it easy to use and full of helpful operating tips and SAFETY messages.
Make sure the decals are legible and that you understand and follow the instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information.
Schedule heavy work for early morning or late afternoon hours when temperatures are cooler. Hearing Protection -- ECHO recommends wearing hearing protection whenever unit is used.
ILLER ULTIVATOR PERATOR ANUAL EXTENDED OPERATION EXTREME CONDITIONS Vibration and Cold -- To reduce the risk of RSI/CTS, do the It is believed that a condition called Raynaud’s Phenomenon, which following: affects the fingers of certain individuals may be brought about by exposure to vibration and cold.
• BEFORE OPERATION, refer to your Operator’s Manual for proper operating techniques. • If you require a replacement manual, contact ECHO, Inc. , 400 Oakwood Road, Lake Zurich, IL 60047. • Always empty the fuel tank before carrying unit in a car or truck. To avoid damage to engine parts always lay unit on its muffler side.
The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions some assembly is required. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts.
Page 8
1. STOP SWITCH - Toggle Switch mounted on upper right handle. Move switch forward to "Start" position to run, back to "Stop" position to stop unit. 2. THROTTLE TRIGGER - Spring loaded to return to idle when released. When accelerating, pull trigger gradually for best operating technique.
Spark Plug -------------------------------------------------- NGK BPM-8Y Gap 0.65 mm (0.026 in.) Fuel ---------------------------------------------------------- Mixed (Gasoline and Two-stroke Oil) Fuel/Oil Ratio ----------------------------------------------- 50:1 ECHO High Performance, two-stroke air cooled engine oil Gasoline ----------------------------------------------------- 89 Octane unleaded. DO NOT use fuel containing methyl alcohol, more than 10% ethyl alcohol or 15% MTBE.
SSEMBLY Tools Required: (2) 7/16 in. Wrenches 1. Support powerhead assembly upright on tines. Place top handle assembly to rear. NOTE Make sure inside curves at handle ends are facing each other. 2. Loosely assemble lower handles using short 1/4 in. x 3 in. long hex head shoulder bolt (A), eye plates (B), lockwasher (C), and locknut (D) in front handle end mounting hole as shown.
ISO-L-EGD and J.A.S.O. FC • Wipe any spilled fuel from the unit. certified oil, such as Echo Premium 50:1 Two-stroke Oil, will void the • Move at least 3 m (10 ft.) from refueling two-stroke engine warranty.
DANGER The tines should not move at idle. If tines move, readjust carburetor according to "Carburetor Adjustment" instructions in this manual or see your ECHO Dealer, otherwise serious personal injury may result. 1. Stop Switch Move Stop Switch (A) to "START" position.
Move stop switch to "STOP" position (A). WARNING DANGER If engine does not stop when stop switch is moved to STOP position, close choke - COLD START position - to stall engine. Have your ECHO dealer repair stop switch before using tiller/ cultivator again.
• Big Weeds/Tough Roots: Rock TC-210 back and forth over tough spot until the tines slice through the roots or weeds. • Digging Holes: Hold TC-210 in place, and allow tines to dig down into the soil. Allow tines to dig approximately 6 – 8 inches deep, then lift unit up and out.
ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOUR- SELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed, see your ECHO dealer for repairs.
AIR FILTER Level 1. Tools required: 25-50mm (1-2 in.) medium bristle paint brush. Parts required: 90008 REPOWER AIR & FUEL FILTER KIT. 1. Close choke (Cold Start Position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumu- lated dirt from the air cleaner area.
The cylinder exhaust port must be inspected and cleaned of excess carbon every 3 months or 90 hours of operation in order to maintain this engine within the emissions durability period. ECHO strongly recommends that you return your unit to your ECHO dealer for this important maintenance service. EXHAUST SYSTEM Spark Arrestor Screen Level 2.
PERATOR ANUAL CARBURETOR ADJUSTMENT Level 2. Tools required: Screwdriver, Tachometer (ECHO P/N 99051130017). Parts required: None. NOTE Every unit is run at the factory and the carburetor is set in compli- ance with emission regulations. In addition, the carburetor is equipped with HI (A) and LO (B) needle adjustment limiters that prevent settings outside acceptable limits.
LUBRICATION Level 1. Tools Required: Crosshead Screw Driver, Clean Rag Parts Required: ECHO LUBE 8 oz. (P/N 91015) or Lithium Base ® Grease. Gear Housing 1. Remove tines (See Tine Removal/Cleaning - Installation below). 2. Clean dirt from area around gear cover (A) and remove four (4) crosshead screws (B).
ILLER ULTIVATOR PERATOR ANUAL ROUBLESHOOTING t l i f l f f t ' n t n I t l i f t l i f t l i f t l i f t r i WARNING DANGER Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by grounding spark plug against cylinder, otherwise serious personal injury may result.
TORAGE Long Term Storage (over 30 days) WARNING DANGER During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result.
• Sending a check or money order for $2.00 per Parts Catalog or $1.50 per Operator's Manual made payable to ECHO, INCORPORATED. State on a sheet of paper the model number and serial number of the ECHO unit you have, part number of the manual (if known), your name and address and mail to address below.