Operation - 3-Stage Remote - Dimplex EF3003 Service Manual

Timer Mode
You can set the timer to the length of time you want the unit
to operate (1 to 120 minutes).
1. With the unit Off, press the TImER button once. The
timer display will blink "---"
2. Press the uP and DOWN buttons to adjust the timer
display in minutes.
3. Press the TImER button once to set the timer.
!
NOTE: The timer setting can be reset by pressing the
TImER button and using the DOWN button until the timer
display reads "----", press the TImER button once to set the
timer.
4. Press the POWER button to turn the unit on.
5. The fireplace will automatically shut off when the timer
reaches 0 minutes.
Child Proof Function
1. Remove the battery cover on the back of the remote
control.
2. Slide the small blue switch down to activate the child
proof function.
3. Child Proof will appear on the display screen and all
function on the remote control will be locked.
4. To enable normal remote control operation when the
child proof function is activated, press the up and down
buttons in the following sequence:
• uP-DOWN-DOWN-uP-DOWN the remote functions
will now operate normally. The remote control will
return to the child proof function if buttons are not
pressed after two minutes.
5. To disable the child proof function remove the battery
cover on the back of the remote control and slide the
small blue switch up.
Battery Replacement
The remote control uses 3 AAA size batteries (included).
Replace these batteries at least every 6 months or when
the low battery icon appears on the remote control display
screen. When batteries are removed wait at least 1 minute
before replacing with new batteries.
Code selection
If the current remote control is interfering with the operation
of other remote control devices (Tv, vCR, garage doors
etc.) The code can be changed on the remote control.
To change code:
1. Remove the battery cover on the back of the remote
control.
2. Slide the four small switches to any configuration other
than the factory set code.
3. Remove the batteries, wait for one minute.
4. Install the batteries.
5. Install the battery cover onto the remote control.
6. Reinitialize the remote control to match the new code
to the remote control receiver.
4

OPERATION - 3-STAgE REMOTE

(EF3003/SF3003/DF3003 MOD C-E, All DFB6016 Units)
Figure 3
C
B
D
MANUAL CONTROLS (Figure 3)
A. Main On/Off Switch
The fireplace has a Main On/Off switch located on the
control panel of the fireplace. Toggle the switch to turn the
fireplace On and Off.
B. Light Dimmer
Turn the flame brightness control knob to increase or
decrease the brightness of the flame and embers.
C. Flame Action Control
Turn the flame action control knob to adjust the flame
speed to the desired level.
D. 3-Position Switch
Operates the electric fireplace manually. Pressing the
switch up (" " position) once turns on the electric
fireplace and activates Level 1, twice activates Level 2,
three times activates Level 3.
Pressing the switch down ("
fireplace OFF.
Level 1 : The flame effect is turned on and the first red
indicator light illuminates.
Level 2 :
The flame effect remains on, the heater is
activated to the low heat setting, and the first and
second red indicator lights
Level 3 : The flame effect remains on, the heater is
set to the high heat setting, and all three red indicators
illuminate.
Resetting the Temperature Cutoff Switch
Should the heater overheat, an automatic cut out will turn
the heater off and it will not come back on without being
reset. It can be reset by switching the main On/Off Switch
to Off and waiting five (5) minutes before switching the unit
back on.
CAUTION: If you need to continuously reset the heater,
unplug the unit and call Dimplex North America Limited
at 1-888-346-7539.
Remote Control
The fireplace is supplied with a radio frequency remote
control. This remote control has a range of approximately
A
" position) turns the electric
illuminate.
www.dimplex.com