Switch Replacement - On/Off And Heater; Light Dimmer Replacement (Mod 0-C); Light Dimmer Replacement (Mod D); Flicker Motor/Flicker Rod Replacement (Mod 0-A) - Dimplex CDS6599 - Celeste Service Manual

Switch Replacement - On/Off and Heater

WARNINg: If unit was operating prior to servicing allow
at least 10 minutes for light bulbs and heating element to
cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
Tools Required: Phillips head Screwdriver
1. Remove the stove pipe kit (if equipped).
2. Remove the 2 screws at the upper corners of the back
panel. Lift the back end of the top to clear the brackets
and pull back. Lift top carefully, and place to the side of
the stove. Caution should be taken as the top mounting
brackets may scratch the finish.
3. Locate the switch, that requires replacement, mounted
on the rear panel and disconnect the wiring clips and
connections, noting their original locations.
! NOTE: A flat head screwdriver can be used to gently pry
between the end of the connector and the switch to release
the wires.
4. Depress the retainer clips on the rear of the switch and
push the switch out of the rear cover.
5. Properly orient the new switch and reconnect all of the
wiring clips and connections.
6. Reassemble in the reverse order as above.

Light Dimmer Replacement (MOD 0-C)

WARNINg: If unit was operating prior to servicing allow
at least 10 minutes for light bulbs and heating element to
cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
Tools Required: Phillips head Screwdriver
Flat Head Screwdriver
1. Remove the stove pipe kit (if equipped).
2. Remove the 2 screws at the upper corners of the back
panel. Lift the back end of the top to clear the brackets
and pull back. Lift top carefully, and place to the side of
the stove. Caution should be taken as the top mounting
brackets may scratch the finish.
3. Remove the upper light bulb, the light socket retaining
screw and the wiring from the wiring clip mounted to the
underside of the top.
4. Locate the light dimmer, mounted on the rear panel, and
pull off the control knob.
5. Remove the light dimmer retaining nut.
6. Pull the light dimmer out from the back of the rear panel.
7. Locate the wiring connections for the light dimmer and
disconnect the wiring connections, noting their original
locations.
! NOTE: In some models you will be required to remove
the light cover mounting screws to complete the replacement.
Remove the light cover, being careful not to damage any of
the wiring or light bulbs.
8. Properly orient the new dimmer and reconnect all of the
wiring clips and connections.
9. Reassemble in the reverse order as above.

Light Dimmer Replacement (MOD D)

WARNINg: If unit was operating prior to servicing allow
at least 10 minutes for light bulbs and heating element to
cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
Tools Required: Phillips head Screwdriver
1. Remove the stove pipe kit (if equipped).
2. Remove the 2 screws at the upper corners of the back
panel. Lift the back end of the top to clear the brackets
and pull back. Lift top carefully, and place to the side of
the stove. Caution should be taken as the top mounting
brackets may scratch the finish.
3. Remove the upper light bulb, the light socket retaining
screw and the wiring from the wiring clip mounted to the
underside of the top.
4. Locate the light dimmer, mounted on the rear panel, and
pull off the dimmer control knob.
5. Remove the light dimmer retaining nut.
6. Pull the light dimmer out from the back of the rear panel.
7. Gently place stove on its back on a flat surface.
8. Remove the heater cover retaining screws located on the
bottom of the stove and lower heater and light assembly
out onto the floor.
9. Remove all of the mounting screws on the heater cover
and separate the cover from the heater and light assem-
bly.
10. Locate the wiring connections for the light dimmer and
disconnect the wiring connection, noting its original loca-
tion.
11. Properly orient the new dimmer and reconnect all of the
wiring clips and connections.
12. Reassemble in the reverse order as above.
Flicker Motor/Flicker Rod Replacement
(Mod 0-A)
WARNINg: If unit was operating prior to servicing allow
at least 10 minutes for light bulbs and heating element to
cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
Tools Required: Phillips head Screwdriver
1. Remove the stove pipe kit (if equipped).
2. Gently place stove front side up on a flat surface.
3. Remove the heater cover retaining screws located on the
bottom of the stove.
4. Lift stove back on its feet and remove the 2 screws at the
upper corners of the back panel. Lift the back end of the
7